金属氧化物包覆LiMn_2O_4的红外光谱及光电子能谱研究

本文采用溶液化学的方法,在锂离子电池正极材料LiMn2O4上包覆一层金属氢氧化物前驱体,再通过热处理得到稳定的金属氧化物包覆层。傅立叶红外光谱(FIIR)的研究表明,当包覆LiMn2O4中外来金属原子的实际百分比小于1.11%时,不能探测到包覆层红外信号。X射线光电子能谱(XPS)的研究表明,表面包覆层中Al或Mg的存在不仅削弱Mn-O键的作用,而且给体系引入过多的正电荷,导致Mn(2p)结合能的降低。包覆层中的Al2O3和MgO均在加热过程中向LiMn2O4体相中扩散;而包覆层中的SnO2在焙烧后并未进入LiMn2O4晶格内,而是附着于其表面。     

Pu(100)表面吸附CO2的密度泛函研究

采用广义梯度密度泛函理论的改进Perdew-Burke-Ernzerh方法结合周期性层晶模型,研究了CO₂分子在Pu（100）面上的吸附和解离.吸附能和几何构型的计算表明,CO₂以穴位C4O4构型吸附最为有利,吸附能为1.48 eV.布居分析和态密度分析表明,CO₂与Pu表面相互作用的本质主要是CO₂分子的杂化轨道2π_μ与Pu5f,Pu6d,Pu7s轨道通过强电子转移和弱重叠杂化的方式相互作用而生成了新的化学键.计算的CO₂→CO+O解离能垒为0.66 eV,解离吸附能为2.65 eV, 表明在一定热激活条件下CO₂分子倾向于发生解离性吸附.O₂,H₂,CO和CO₂在Pu （100）面吸附的比较分析表明,较低温度下的吸附强度顺序依次为O₂,CO,CO₂,H₂;较高温度下的吸附强度顺序依次为O₂,CO₂,CO,H₂. 关键词： 密度泛函理论 Pu （100） 2')" href="#">CO₂ 吸附和解离     

CO在Pu(100)表面吸附的研究

采用密度泛函理论(DFT)研究了CO分子在Pu (100)面上的吸附. 计算结果表明：CO在Pu (100)表面的C端吸附比O端吸附更为有利，属于强化学吸附. CO吸附态的稳定性为穴位倾斜>穴位垂直>桥位>顶位. CO分子与表面Pu原子的相互作用主要源于CO分子的杂化轨道和Pu原子的杂化轨道的贡献. 穴位倾斜吸附的CO分子的离解能垒较小(0.280eV)，表明在较低温度下，CO分子在Pu (100)表面会发生离解吸附，离解的C，O原子将占据能量最低的穴位.     

CO在Pu(100)表面吸附的研究

采用密度泛函理论(DFT)研究了CO分子在Pu (100)面上的吸附. 计算结果表明：CO在Pu (100)表面的C端吸附比O端吸附更为有利,属于强化学吸附. CO吸附态的稳定性为穴位倾斜>穴位垂直>桥位>顶位. CO分子与表面Pu原子的相互作用主要源于CO分子的杂化轨道和Pu原子的杂化轨道的贡献. 穴位倾斜吸附的CO分子的离解能垒较小(0.280eV),表明在较低温度下,CO分子在Pu (100)表面会发生离解吸附,离解的C,O原子将占据能量最低的穴位. 关键词： 密度泛函理论 Pu (100) CO 分子和离解吸附     

Ionic liquid-based electrolyte with dual-functional LiDFOB additive toward high-performance LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> batteries

Manganese oxide-based cathodes are one of the most promising lithium-ion battery (LIB) cathode materials due to their cost-effectiveness, high discharge voltage plateau (above 4.0 V vs. Li/Li⁺), superior rate capability, and environmental benignity. However, these batteries using conventional LiPF₆-based electrolytes suffer from Mn dissolution and poor cyclic capability at elevated temperature. In this paper, the ionic liquid (IL)-based electrolytes, consisting of 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfon)imidate (PYR_1,4-TFSI), propylene carbonate (PC), lithium bis(trifluoromethanesulfon)imide (LiTFSI), and lithium oxalyldifluoroborate (LiDFOB) additive, were explored for improving the high temperature performance of the LiMn₂O₄ batteries. It was demonstrated that LiTFSI-ILs/PC electrolyte associated with LiDFOB addition possessed less Mn dissolution and Al corrosion at the elevated temperature in LiMn₂O₄/Li batteries. Cyclic voltammetry and electrochemical impedance spectroscopy implied that this kind of electrolyte also contributed to the formation of a highly stable solid electrolyte interface (SEI), which was in accordance with the polarization measurement and the Li deposition morphology of the symmetric lithium metal cell, thus beneficial for improving the cycling performance of the LiMn₂O₄ batteries at the elevated temperature. Cyclic voltammetry and electrochemical impedance spectroscopy implied that the cells using this kind of electrolyte exhibited better interfacial stability, which was further verified by the polarization measurement and the Li deposition morphology of the symmetric lithium metal cell, thus beneficial for improving the cycling performance of the LiMn₂O₄ batteries at the elevated temperature. These unique characteristics would endow this kind of electrolyte a very promising candidate for the manganese oxide-based batteries.     

LCAO studies of hydrogen chemisorption on nickel: II. Cluster models for adsorption sites

The adsorption of single hydrogen atoms, investigated by means of cluster calculations, has been compared with the adsorption of hydrogen monolayers on periodic crystals (paper I). From the similarity of the adsorption energy curves we conclude that the (direct and indirect) interactions between adsorbed hydrogen atoms are relatively small up to monolayer coverage. For adsorption on different sites of ideal low index surfaces the stability decreases in the order Atop > Bridge > Centred. For Atop adsorption it increases with a decreasing number of nearest neighbours to the nickel atom in the NiH “surface molecule”, thus leading to especially strong adsorption sites at the edges of a stepped surface and to low stability in the notches. In general, we find that the Ni_nH “surface molecule” with n = 1, 2, 3 or 4 determines the equilibrium positions for H adsorption; the inclusion of one shell of neighbours to the nickel atoms is sufficient to explain the differences in adsorption energy. The Extended Hückel method is not well suited to study dissociative chemisorption of H₂, although some qualitative trends are correct.     

N2O在Yn(n=2-7)团簇表面的自然解离

运用第一性原理，研究了N2O在Yn (n=2-7) 团簇表面吸附机理。结果表明：N2O吸附于 Yn (n=2-7)团簇表面时，不需要克服任何能垒而自然解离。吸附导致了主团簇Y原子平均键长增大,体系表现出了巨大的吸附能 (约为8-10eV)。吸附对体系化学活性的影响具有一定的尺寸依赖性。在所有团簇中，Y6N2O吸附能最大，化学性质最稳定。     

N_2O在Y_n(n=2-7)团簇表面的自然解离

运用第一性原理,研究了N2O在Yn(n=2-7)团簇表面吸附机理.结果表明:N_2O吸附于Yn(n=2-7)团簇表面时,不需要克服任何能垒而自然解离.吸附导致了主团簇Y原子平均键长增大,体系表现出了巨大的吸附能(约为8-10 e V).吸附对体系化学活性的影响具有一定的尺寸依赖性.在所有团簇中,Y_6N_2O吸附能最大,化学性质最稳定.     

TiO2分子在GaN(0001)表面吸附的理论研究

采用基于密度泛函理论的平面波超软赝势法,计算了TiO₂分子在GaN(0001)表面的吸附成键过程、吸附能量和吸附位置. 计算结果表明不同初始位置的TiO₂分子吸附后,Ti在fcc或hcp位置,两个O原子分别与表面两个Ga原子成键,Ga-O化学键表现出共价键特征,化学结合能达到7.932-7.943eV,O-O连线与GaN[1120]方向平行,与实验观测(100)[001] TiO₂//(0001)[1120]GaN一致. 通过动力学过程计算分析,TiO₂分子吸附过程经历了物理吸附、化学吸附与稳定态形成的过程,稳定吸附结构和优化结果一致. 关键词： GaN(0001)表面 2分子')" href="#">TiO₂分子 密度泛函理论 吸附     

锂薄膜的第一性原理计算:量子尺寸效应和原子氢的吸附

采用第一性原理方法计算Li（110）、（100）和（111）三个表面方向3至30层自由薄膜的表面能和氢原子的吸附能.随着层厚变化出现量子振荡现象,即量子尺寸效应.重点计算Li（110）表面吸附氢原子吸附高度、吸附氢原子前后费米能级处的态密度和功函数.这些量都随着层厚变化出现明显的量子振荡,且与表面能或吸附能的振荡有明显的相关性.计算发现Li（110）薄膜表面的功函数由于吸附氢原子而降低了约0.9 eV,吸附的氢原子拉低了最外层Li原子和真空层的静电势,导致吸附氢原子后功函数下降.     

Design of ionic liquid-based hybrid electrolytes with additive for lithium insertion in graphite effectively and their effects on interfacial properties

To address the challenge of the IL-based electrolyte cannot be effectively intercalated in graphite anode, and especially the urgent needs for the compatibility between high performance and high security, the IL-based hybrid electrolyte systems with ethylene carbonate/propylene carbonate (EC/PC) as a co-solvent and vinylene carbonate (VC) as an additive were designed. The high dielectric constant of EC/PC significantly increased the ionic conductivity and lithium ion migration of the electrolyte system. Meanwhile, the presence of VC can form SEI preventing EC and PYR₁₄⁺ reductive decomposition on the electrode interface, and at the same moment, the SEI promotes effective Li cation insertion into the graphene interlayer. The Li/C half-cells showed high reversible capacity, cycling efficiency, and good cycle stability with the IL-based hybrid electrolyte. It is worth to highlight the better performance, in terms of the excellent thermal stability and high safety. Thus, the IL-based hybrid electrolyte combined with good electrochemical performance holds substantial promise for lithium-ion battery, and should have broad application prospects in the high energy density, especially high-security requirements, of the new lithium-ion battery.     

Role of oxygen functional groups for structure and dynamics of interfacial water on low rank coal surface: a molecular dynamics simulation

Molecular dynamics simulations were employed to study the effects of oxygen functional groups for structure and dynamics properties of interfacial water molecules on the subbituminous coal surface. Because of complex composition and structure, the graphite surface modified by hydroxyl, carboxyl and carbonyl groups was used to represent the surface model of subbituminous coal according to XPS results, and the composing proportion for hydroxyl, carbonyl and carboxyl is 25:3:5. The hydration energy with ?386.28 kJ/mol means that the adsorption process between water and coal surface is spontaneous. Density profiles for oxygen atoms and hydrogen atoms indicate that the coal surface properties affect the structural and dynamic characteristics of the interfacial water molecules. The interfacial water exhibits much more ordering than bulk water. The results of radial distribution functions, mean square displacement and local self-diffusion coefficient for water molecule related to three oxygen moieties confirmed that the water molecules prefer to absorb with carboxylic groups, and adsorption of water molecules at the hydroxyl and carbonyl is similar.     

Behavior of zirconium in the ZrOW(100) system at high temperature, studied by ISS, AES and work-function measurements

The behavior of zirconium atoms at the W(100) surface associated with oxygen adsorption at different sample temperatures has been studied by Auger electron spectroscopy (AES), ion scattering spectroscopy (ISS), and the relative change of the work function (Δф) measured by the onset of the secondary electron energy distribution. The results have revealed: (i) adsorption of zirconium onto the W(100) surface followed by the elevation of the sample temperature up to 1710 K in an oxygen partial pressure of 2.7 × 10⁻⁴ induces complete diffusion of zirconium atoms into the W(100) substrate; (ii) further exposure of oxygen induces co-existence of oxygen and tungsten on the surface at 1710 K, resulting in a work function of 4.37 eV; (iii) keeping the sample temperature at 1710 K, simple evacuation of the system has resulted in surface segregation of zirconium atoms to the surface to form a zirconium atomic layer on the top-most surface, reducing the work function to 2.7 eV. The results have revealed that this specific behavior of zirconium atoms at high temperature assures, with very good reproducibility, the highly stable performance and long service life of Zr---O/W(100)-emitters in practical use, even in a low vacuum of 10⁻⁶ Pa.     

Trimethoxymethylsilane as a solid-electrolyte interphases improver for graphite anode

To improve the cycling performance of graphite anode materials, we propose a functional electrolyte additive, trimethoxymethylsilane (TMSi), which contains a silyl ether functional group as part of its molecular structure. First principal calculation studies, in addition to ex situ analyses, demonstrated that electrochemical reduction of ethylene carbonate (EC) gives an anionic reduced EC product. Subsequent chemical reaction with TMSi then generates solid-electrolyte interphase (SEI) layers of Si–O and Si–C functionalized carbonate on the surface of the graphite anode, which prolongs and stabilizes the cycling performance of the cells. As a result, the cell cycled with TMSi-controlled electrolyte exhibits a cycling retention of 89.5%, whereas the cell cycled with standard electrolyte suffers from poor cycling retention (84.3%) after 100 cycles.     

Influence of Pb adatom on adsorption of oxygen molecules on Pb(111) surface: a first-principles study

Using first-principles calculations, we systematically study the influence of Pb adatom on the adsorption and the dissociation of oxygen molecules on Pb(111) surface, to explore the effect of a point defect on the oxidation of the Pb(111) surface. We find that when an oxygen molecule is adsorbed near an adatom on the Pb surface, the molecule will be dissociated without any obvious barriers, and the dissociated O atoms bond with both the adatom and the surface Pb atoms. The adsorption energy in this situation is much larger than that on a clean Pb surface. Besides, for an adsorbed oxygen molecule on a clean Pb surface, a diffusing Pb adatom can also change its adsorption state and enlarge the adsorption energy for O, but it does not make the oxygen molecule dissociated. And in this situation, there is a molecule-like PbO2 cluster formed on the Pb surface.     

Initial stage of the adsorption of fluorofullerene molecules on Si surface

Spatially resolved images of an individual C₆₀F₁₈ fluorofullerene molecule on Si(100) − 2 × 1 surface have been obtained using scanning tunneling microscopy. Scanning tunneling microscopy results and ab initio calculations show that the fluorofullerene molecules interact with the Si(100) − 2 × 1 surface with F atoms pointing down towards the surface. The adsorption energy of a C₆₀F₁₈ molecule on Si(100) − 2 × 1 surface is ∼12.1 eV, which is much higher than the adsorption energy of the same molecule on Si(111) − 7 × 7 surface (6.65 eV). C₆₀F₁₈ molecules are located in the troughs in-between the dimer rows occupying the four-dimer site on Si(100) − 2 × 1 surface.     

Ionic conduction and phase separation studies in P(VdF-HFP))-LiClO4-dedoped polyaniline nanofiber composite polymer electrolytes — II: Effect of incorporation of PC and DEC

In the present work, ionic transport and interfacial stability of dedoped (insulating) polyaniline (PAni) nanofibers dispersed P(VdF-HFP) based nanocomposite gel polymer electrolytes have been investigated. Samples of P(VdF-HFP)-(PC+DEC)-LiClO₄-x wt. % dedoped PAni nanofibers (x = 0, 2, 4, 6, 8, 10) are prepared by conventional solution casting technique. By analysis of SEM, XRD and impedance spectroscopy results it has been demonstrated that the incorporation of up to 6 wt. % of dedoped PAni nanofibers to P(VdF-HFP)-(PC+DEC)-LiClO₄ polymer electrolyte system significantly enhances the ionic conductivity and interfacial stability of the electrolyte system. Above that concentration phase separation of PAni nanofibers is observed leading to decrease in ionic conductivity. The aggregated phase decreases the porosity, which results in lower ionic conductivity as confirmed by SEM. Experiments on the interfacial stability reveals that the stability of polymer electrolytes containing nanofibers is better than that of nanofiber free polymer electrolytes.     

Corrosion related properties of iron(100) surface in liquid lead and bismuth environments:A first-principles study

The corrosion of steels in liquid metal lead （Pb） and bismuth （Bi） is a critical challenge in the development of accel-erator driven systems （ADS）. Using a first-principles method with a slab model, we theoretically investigate the interaction between the Pb （Bi） atom and the iron （Fe） （100） surface to assess the fundamental corrosion properties. Our investigation demonstrates that both Pb and Bi atoms favorably adsorb on the （100） surface. Such an adsorption decreases the energy required for the dissociation of an Fe atom from the surface, enhancing the dissolution tendency significantly. The seg- regation of six common alloying elements （Cr, A1, Mn, Ni, Nb, and Si） to the surface and their impacts on the corrosion properties are also considered. The present results reveal that Si seems to have a relatively good performance to stabilize the surface and alleviate the dissolving trend caused by Pb and Bi.     

WO_3(001)表面活性氧物种的理论研究

采用第一性原理结合周期性平板模型的方法,对O_2在完整和缺陷WO_3(001)表面的吸附行为进行了研究.结果表明:WO_3(001)完整表面上吸附态的O_2不易成为表面氧化反应的活性氧物种,当吸附质与表面作用时,将优先与表面晶格氧(O_t)成键,进而形成表面缺陷态,体系呈现金属性,电导率增大.比较O_2在缺陷表面上各吸附构型的吸附能发现,O_2的吸附倾向于发生在缺陷位置(W_v)上,且表现为氧气分子中的两个氧原子均与缺陷位W_v作用,形成新的活性氧物种(O_2~-);吸附后表面被氧化,电导率降低.     

金属原子修饰石墨烯体系催化性能的理论研究

采用基于密度泛函理论的第一性原理方法研究了单个CO和O2气体分子在金属原子修饰石墨烯表面的吸附和反应过程.结果表明:空位缺陷结构的石墨烯能够提高金属原子的稳定性,金属原子掺杂的石墨烯体系能够调控气体分子的吸附特性.通入混合的CO和O2作为反应气体,石墨烯表面容易被吸附性更强的O2分子占据,进而防止催化剂的CO中毒.此外,对比分析两种催化机理(Langmuir-Hinshelwood和Eley-Rideal)对CO氧化反应的影响.与其它金属原子相比,Al原子掺杂的石墨烯体系具有极低的反应势垒(0.4 e V),更有助于CO氧化反应的迅速进行.