多孔NiTi合金的化学氧化处理表面改性研究

在H2O2+HCl溶液中对多孔NiTi合金进行了化学氧化处理表面改性。利用EPMA、SEM、原子吸收光谱对合金表面氧化膜的组成、形貌及化学氧化处理前后的Ni离子释出进行了研究。结果表明,经过H2O2+HCl溶液化学氧化表面处理后合金表面Ni含量显著降低,在生理盐水中的Ni释放速率明显下降;H2O2+HCl溶液浓度和氧化时间均对合金表面氧化膜的生长有较大影响。     

NiTi合金生物医用材料表面改性的研究进展

NiTi合金由于其形状记忆效应、超弹性和低模量等优良性能在生物医学领域得到广泛应用。然而,在生理环境中镍离子释放会诱发毒性和炎性反应,因此需要对其进行表面改性。从表面氧化、表面涂层和表面接枝大分子等方面综述了近年来国内外NiTi合金表面改性的研究进展,评述了各种表面改性技术的优势和缺陷,指明了NiTi合金表面改性的未来发展趋势。     

NiTi合金生物医用材料表面改性的研究进展

NiTi合金由于其形状记忆效应、超弹性和低模量等优良性能在生物医学领域得到广泛应用。然而，在生理环境中镍离子释放会诱发毒性和炎性反应，因此需要对其进行表面改性。从表面氧化、表面涂层和表面接枝大分子等方面综述了近年来国内外NiTi合金表面改性的研究进展，评述了各种表面改性技术的优势和缺陷，指明了NiTi合金表面改性的未来...     

医用多孔NiTi合金表面微弧氧化改性研究

为解决多孔Ni Ti合金耐蚀性降低和Ni离子释放量增大而引起的使用安全性问题.本文采用微弧氧化技术对医用多孔Ni Ti合金进行表面改性处理,研究结果表明,微弧氧化处理并未改变多孔Ni Ti合金原有的孔隙结构和孔隙率,只在其外表面和孔隙内表面均形成了典型的微弧氧化多孔涂层.该涂层主要由氧化铝相组成,并含有少量的Ti和Ni元素,且外表面涂层的Ti和Ni含量要略低于孔隙内表面涂层.微弧氧化涂层提高了多孔Ni Ti合金的表面接触角,将原有的亲水表面转变成了疏水表面.经微弧处理后,多孔Ni Ti合金的耐蚀性较基体提高了1个数量级以上,Ni离子释放量也较基体降低了1个数量级以上.     

不同等离子源形成的DLC涂层对NiTi合金腐蚀行为的影响

采用等离子浸没离子注入和沉积(PIIID)法分别以C2H2和石墨为等离子源在NiTi合金表面形成DLC涂层来提高该合金的耐腐蚀性.利用Raman光谱和扫描电镜分析膜层结构.利用电化学测试和原子吸收光谱测试涂层前后基体的耐腐蚀性和Ni离子析出.结果表明:采用等离子浸没离子注入和沉积法以乙炔和石墨为等离子源在NiTi合金表面形成均匀致密、结合力良好的DLC涂层.两种涂层都明显地提高了NiTi合金的耐腐蚀性能和有效地抑制了Ni离子的溶出.     

NiTi合金生物医用材料表面改性的研究进展

NiTi形状记忆合金作为重要的生物医用材料已经获得了广泛的应用,但Ni离子在人体环境中的释放引起了人们的忧虑.系统介绍了近年来表面改性提高NiTi合金生物相容性的主要方法、技术特点和优势.在众多的研究方法中,热氧化和自组装方法因具有工艺简单、成本低等优点而最具工业应用前景.有关NiTi合金表面涂层与细胞和血液的相互作用机理的研究亟待加强,微观方面应重视基因水平的评价,宏观方面应加强活体植入的研究.研究机构应与产业界密切配合,进一步推动相关涂层的产业化进程.     

NiTi形状记忆合金表面改性的研究进展

近等原子比的NiTi合金以其优异的特性在临床医学得到广泛应用,但是由于Ni离子溶出引致的潜在生物毒性以及无生物活性,抑制了NiTi合金在生物医用领域的进一步发展。为了改善上述缺陷,对NiTi合金进行表面处理成为当前国内外NiTi合金研究的热点。从不同的改性工艺出发,全面阐述了近年来国内外对致密态和多孔态NiTi合金进行表面改性的研究进展,对各种方法可能出现的问题进行了分析,指出现有的各种表面改性方法不能有效实现对多孔NiTi合金内部孔隙进行改性,并针对这一症结提出了采用原位氮化法对多孔NiTi合金进行改性的可行性。     

不锈钢表面阴极等离子体液相沉积氧化铝层

使用阴极等离子体液相沉积技术在不锈钢表面生成了厚度达40μm的氧化铝膜层,研究了电流密度对膜层的组成和结构影响,以及膜层的生长规律和形成过程.膜层由α-Al2O3和γ-Al2O3组成,随着电流密度的增大,α-Al2O3的含量逐渐增大,电流密度为8 A/dm2时达到86%.膜层的表面粗糙、多孔,随着电流密度的增大,表面颗粒状明显增多,微孔数减少;基体中的Fe没有进入膜层,从膜层内向外Al和O的含量逐渐下降.     

钛表面阴极微弧电沉积制备氧化铝涂层

采用阴极微弧电沉积在钛表面生成了厚度达100μm的氧化铝涂层,研究了不同电压下涂层的结构和组成,分析了涂层的生长规律和形成过程.结果表明：阴极微弧电沉积过程包括火花前、微弧和局部弧光三个阶段,期间伴随有Al（NO3）3的离解、Al（OH）3的沉积与高温烧结等反应,微弧区产生的高温高压是形成Al2O3涂层的关键.涂层主要由γ-Al2O3和α-Al2O3组成,随电压升高,α-Al2O3的含量逐渐增加,在400V时其含量达76%.     

NiTi合金低压等离子渗氮研究

采用低压等离子渗氮工艺对NiTi合金进行了渗氮处理.氮化处理后NiTi合金表面硬度升高.XRD测试结果表明在合金表面形成了一层TiN涂层,在TiN涂层下为Ni3Ti相.电化学腐蚀测试表明经氮化处理后合金的耐腐蚀能力大为提高.     

纳米Al2O3及PTFE的加入对镀层性能的影响

在化学镀Ni-P合金镀液中添加纳米Al2O3及PTFE制得Ni-P/PTFE-Al2O3复合镀层.研究了纳米Al2O3及PTFE的添加量对镀层硬度、磨损及减摩性能的影响.结果表明:纳米Al2O3及PTFE的加入能提高Ni-P合金镀层的硬度、耐磨及减摩性.     

Characteristics and in vitro biological assessment of (Ti, O, N)/Ti composite coating formed on NiTi shape memory alloy

In this investigation, plasma immersion ion implantation and deposition (PIIID) was used to fabricate a (Ti, O, N)/Ti coating on NiTi shape memory alloy (SMA) to improve its long-term biocompatibility and wear resistance. The surface morphology, composition and roughness of uncoated and coated NiTi SMA samples were examined. Energy dispersive X-ray elemental mapping of cross-sections of (Ti, O, N)/Ti coated NiTi SMA revealed that Ni was depleted from the surface of coated samples. No Ni was detected by X-ray photoelectron spectroscopy on the surface of coated samples. Furthermore, three-point bending tests showed that the composite coating could undergo large deformation without cracking or delamination. After 1 day cell culture, SaOS-2 cells on coated samples spread better than those on uncoated NiTi SMA samples. The proliferation of SaOS-2 cells on coated samples was significantly higher at day 3 and day 7 of cell culture.     

Oxidation Behavior of Pd-Modified Aluminide Coating at High Temperature

(Ni,Pd)Al coating, prepared by low pressure pack cementation on the Ni-base superalloy M38 where Pd-20 wt pct Ni alloy was predeposited, consists of a single β-(Ni,Pd)Al phase. The initial isothermal oxidation behavior of (Ni,Pd)Al coating was investigated by TGA, XRD, SEM/EDS at 800～1100℃. Results show that oxidation kinetics accord preferably with parabolic law at 800, 900 and 1100℃, but not at 1000℃.θ-Al2O3 was observed at 800～1100℃. It is found that Pd plays an important role in accelerating the diffusion of Ti from the substrate to the coating surface in the aluminide coating.     

Structure and properties of TiC/Ti coatings fabricated on NiTi by plasma immersion ion implantation and deposition

A titanium carbide (TiC) nanostructured coating and Ti intermediate layer are fabricated on NiTi by plasma immersion ion implantation and deposition (PIII&D) to improve the surface properties. The chemical composition and structure are determined by X-ray diffraction, Auger electron spectroscopy, scanning electron microscopy, and atomic force microscopy. Nano-indentation is used to evaluate the mechanical properties of the thin film and the biological characteristics are assessed by electrochemical measurement and soaking tests in simulated body fluids. Based on the potentiodynamic polarization and Ni release data after the polarization test, the Ti/TiC nanostructure coating has better corrosion resistance compared to the NiTi substrate and there is significantly less Ni ion release from the NiTi substrate into the simulated body fluids than the uncoated NiTi alloy.     

Fabrication and biocompatibility of polyethyleneimine/heparin self-assembly coating on NiTi alloy

NiTi alloy has been used widely as biomaterials. But because of toxic effects possibly caused by excess Ni ions released during the corrosion process in the physiological environment, it is still a controversial material. Fabricating medicine-loaded coating, which is expected to decrease the release of Ni ions and improve the biocompatibility of the materials, is a potential way to solve the problem. In this paper, NiTi alloy is coated by polyethyleneimine/heparin films via layer-by-layer (LBL) self-assembly method. UV-Vis, FT-IR, atomic force microscopy (AFM) and contact angle measurements are used to characterize the microstructure of coatings and select the best fabrication conditions. Potentiodynamic polarization researches in sodium chloride and dynamic clotting time experiment are utilized to study its corrosion resistance capability and biocompatibility of coatings, respectively. The results indicate that PEI/heparin multilayer coating can improve the biocompatibility of NiTi alloy surface.     

2024铝合金微弧氧化涂层的耐磨性能

为了提高2024铝合金的耐磨性,对其进行微弧氧化。利用扫描电镜(SEM)和X射线衍射仪(XRD)分析了涂层的微观组织结构和物相组成;采用高速往复摩擦磨损试验机对2024铝合金微弧氧化涂层在不同载荷下的磨损性能进行了研究,并采用白光三维形貌仪进行磨损形貌分析及磨损体积计算。结果表明:2024铝合金微弧氧化涂层是一种微孔结构,涂层相主要成分为α-Al_2O_3、γ-Al_2O_3,且Al_2O_3具有高硬度、耐磨损的优良特性,有利于提高铝合金的耐磨损性能;微弧氧化涂层的摩擦系数随着载荷的增加而减小,而磨损量随载荷的增加而增加,磨损机理为磨粒磨损。     

Ca/P层对NiTi形状记忆合金生物相容性的影响

用化学法在ＮｉＴｉ形状记忆合金表面修饰了一层Ｃａ／Ｐ层。Ｘ射线分析表明,Ｃａ／Ｐ层的主要成分是Ｃａ５（ＰＯ４）３（ＯＨ）,还有少量的α－Ｃａ２Ｐ２Ｏ７和β－Ｃａ３（ＰＯ４）２。原子吸收光谱的测量表明,Ｃａ／Ｐ层抑制镍离子在人体模拟溶液中的溶出。植入试验的结果表明,Ｃａ／Ｐ层改善了ＮｉＴｉ形状记忆合金的生物相容性。     

激光熔覆法制备Al2O3-TiO2涂层的显微组织与性能研究

采用预置粉末式激光熔覆法在钛合金(Ti-6Al-4V)表面开展了Al_2O_3-13%(质量分数)TiO_2涂层的研究。利用光学显微镜(OM)、扫描电子显微镜(SEM)、X射线衍射分析仪(XRD)和显微硬度计研究了激光熔覆熔池的特征和涂层的显微结构,分析了涂层的成分分布、相组成和显微硬度分布情况。预置粉末激光熔覆制备的Al_2O_3-13%(质量分数)TiO_2涂层界面结合良好,涂层组织均匀,没有明显的裂纹和气孔。激光熔覆涂层表现出明显流线型特征,熔覆层截面分为热影响区、扩散结合区和涂层区。涂层由Ti、AlTi_3、α-Al_2O_3和γ-Al_2O_3等相组成。涂层的显微硬度达到1000~1300HV_(0.3),比基体硬度360~390HV_(0.3)高2倍。