共查询到17条相似文献,搜索用时 171 毫秒
1.
2.
3.
4.
采用基于固有应变法的弹性有限元分析预测大型复杂结构的焊接变形的前提是必须已知焊缝附近的固有变形。结构的焊接残余应力与焊接变形取决于其接头的固有变形大小及分布,因此开发精确计算接头固有变形的方法,并依此建立一个完善的固有变形数据库对于大型复杂结构焊接变形的预测有重要意义。文中提出了几种计算固有变形的方法包括公式法、热弹塑性有限元法、实测法,并分别采用这几种方法对典型T型接头的横向固有收缩与纵向固有收缩进行计算,三种方法得到的结果比较一致。在此基础上,进一步以典型船体结构为研究对象,采用依照这三种方法建立的固有变形数据库对其焊接变形进行预测,并与实测数据进行比较,验证了该数据库的有效性。 相似文献
5.
《船舶力学》2015,(9)
采用基于固有应变法的弹性有限元分析预测大型复杂结构的焊接变形的前提是必须已知焊缝附近的固有变形。结构的焊接残余应力与焊接变形取决于其接头的固有变形大小及分布,因此开发精确计算接头固有变形的方法,并依此建立一个完善的固有变形数据库对于大型复杂结构焊接变形的预测有重要意义。文中提出了几种计算固有变形的方法包括公式法、热弹塑性有限元法、实测法,并分别采用这几种方法对典型T型接头的横向固有收缩与纵向固有收缩进行计算,三种方法得到的结果比较一致。在此基础上,进一步以典型船体结构为研究对象,采用依照这三种方法建立的固有变形数据库对其焊接变形进行预测,并与实测数据进行比较,验证了该数据库的有效性。 相似文献
6.
7.
8.
大型尾部分段装焊固有应变有限元计算精度控制技术 总被引:1,自引:1,他引:0
船舶建造精度控制是对造船全过程的尺寸精度分析与控制,随着船体结构加工精度的不断提高,装配工艺装备、工艺程序的不断优化,船体装配与焊接精度控制的重点是对焊接过程中所产生的变形开展有效监测与防控。固有应变有限元计算是通过避开复杂的焊接过程,采用简单的弹性静载分析,简化计算过程,辅之于专用焊接变形预测软件,对焊接过程中的固有应变进行预测,给出相应的焊接变形补偿量,从而达到精度控制的目标要求,并在575000DWT散货船尾部分段生产实践中加以了应用。 相似文献
9.
船体分段焊接变形仿真 总被引:1,自引:0,他引:1
船体分段在焊接过程中产生的焊接变形会使船体结构强度降低,然而精确预测和控制焊接变形是个难题.文章提供了准确预测焊接变形的固有应变等效载荷法.这种方法运用有限元法结合固有应变理论以及实验结果对焊接变形进行分析:引入简化的弹-塑性分析杆-弹簧模型,通过分析得到固有应变受焊接区域约束度及最高温度分布情况的影响;将固有应变转化为等效载荷,应用弹性有限元分析求得整个结构的焊接变形.计算结果与LEECH计算及实验结果吻合较好. 相似文献
10.
11.
12.
预测船体复杂结构的焊接变形对制造工艺设计和精度控制具有重要的工程价值.基于固有应变理论,利用船体结构焊接变形预测专用软件Weld-sta对多用途船双层底结构焊接变形进行了预测,发现船长方向收缩最大变形量为13.2mm,船宽方向最大变形量14.5 mm.通过数值模拟结果与实验实测值的对比,可以得到软件计算的精度超过80%,验证了固有应变理论及软件用于焊接变形预测的可靠性,并在此基础上针对船体总段船台合拢的焊接变形进行了预测,发现焊接总收缩变形量为50.339 mm,与实际加工经验基本吻合.根据此结论可以针对各船体总段预留合理的焊接变形收缩量,验证了固有应变为基础的弹性板单元有限元预测法在船体总段合拢焊接中应用的可行性. 相似文献
13.
In a Thermal-Elastic-Plastic (TEP) FE analysis to investigate welding induced buckling of large thin plate welded structure such as ship panel, it will be extremely difficult to converge computation and obtain the results when the material and geometrical non-linear behaviors are both considered. In this study, an efficient FE computation which is an elastic FE analysis based on inherent deformation method, is proposed to predict welding induced buckling with employing large deformation theory, and an application in ship panel production is carried out. The proposed FE computation is implemented with two steps:(1) The typical weld joint (fillet weld) existing in considered ship panel structure is conducted with sequential welding using actual welding condition, and welding angular distortion after completely cooling down is measured. A TEP FE analysis with solid elements model is carried out to predict the welding angular distortion, which is validated by comparing with experimental results. Then, inherent deformations in this examined fillet welded joint are evaluated as a loading for the subsequent elastic FE analysis. Also, the simultaneous welding to assemble this fillet welded joint is numerically considered and its inherent deformations are evaluated.(2) To predict the welding induced buckling in the production of ship panel structure, a shell element model of considered ship panel is then employed for elastic FE analysis, in which inherent deformation evaluated beforehand is applied and large deformation is considered. The computed results obviously show welding induced buckling in the considered ship panel structure after welding. With its instability and difficulty for straightening, welding induced buckling prefers to be avoided whenever it is possible. 相似文献
14.
15.
Elastic FE simulation with inherent deformation and interface element is an ideal and practical computational approach for predicting welding distortion in production of thin plate structures. In this study, recent researches on inherent deformation theory and welding induced buckling investigation of ship panel were sequentially introduced. Taking bead-on-plate welding as research objective (plate with 2.28 mm in thickness), integration approach with inherent strain was proposed to accurately and conveniently evaluate magnitude of inherent deformation. Also, average temperature to clarify the mechanism of influential effect of plate width on magnitude of inherent deformation was presented and examined. With the mechanism investigation of welding induced buckling by elastic FE analysis using inherent deformation, an application for predicting and mitigating the welding induced buckling in fabrication of ship panel with thin plates by employing different welding procedure patterns was carried out. Examined intermittent zigzag welding procedure is effective to reduce the magnitude of in-plane inherent shrinkages and control the possible welding induced buckling. 相似文献
16.
预测船体分段焊接变形方法概述 总被引:5,自引:1,他引:4
船体分段在焊接过程中产生的焊接变形会使船体结构强度降低,精确预测和控制焊接变形是现代造船工艺的要求.焊接变形分析方法包括实验法、解析法、数值分析法、等效载荷法等,常用的是后两种方法.数值分析法采用热弹-塑性有限元模型精确模拟焊接现象,但计算工作量大;等效载荷法计算焊接区域的固有应变,并将其转化为等效载荷,进而应用弹性有限元分析求得整个结构的焊接变形. 相似文献
17.
水密横舱壁作为20000TEU集装箱船的关键结构,对尺寸精度的要求十分严苛,尤其是焊接变形严重影响其建造精度。针对这一问题,采用基于固有变形理论的弹性有限元分析,来预测水密横舱壁结构的面外焊接变形。同时,比较了计算固有变形的两种方法的准确度,并且总结了热输入与固有变形各分量的经验公式,还提出了减小面外焊接变形的措施。结果表明,通过与实测数据对比验证了弹性有限元分析可快速、准确地预测水密横舱壁结构的面外焊接变形;对于对接接头,变形反演法比应变积分法得到的横向固有弯曲更准确;热输入与固有变形各分量呈线性递增关系;将整个水密横舱壁结构由原来的3段分成5段,并采用对称焊接顺序,面外焊接变形最小,同时会降低对船厂吊装能力的要求。 相似文献