SiO_2粒子对PMMA/SAN共混体系相分离行为的影响

采用小角激光光散射(SALLS)并结合动态流变学方法,考察了气相法二氧化硅(SiO2)粒子的加入对聚甲基丙烯酸甲酯/苯乙烯-丙烯腈无规共聚物(PMMA/SAN)共混体系相行为的影响,得到了添加SiO2粒子前后的相图,发现SiO2粒子对基体相行为的影响与基体的组成有关.对PMMA/SAN(60/40)体系,加入SiO2粒子后相分离温度上升,但并未改变相分离机理,仍为亚稳单相分解过程(spinodal decomposition,SD);而对于PMMA/SAN(30/70)体系,加入SiO2粒子后却降低了体系的相分离温度.该现象可能是SiO2粒子和基体组分界面间组成与PMMA/SAN共混物基体组成的差异造成的.     

Effect of Nanoclay on the Phase Separation Behavior of Poly（methyl methacrylate）/Poly（vinyl acetate） Binary Polymer Blends

The effect of nanoclay on the phase-separation behavior of poly（methyl methacrylate）/poly（vinyl acetate）（PMMA/PVAc） blends has been mainly investigated by small-angle laser light scattering. It is found that the effect of clay on the thermodynamics and kinetics of phase-separation for PMMA/PVAc blends seems inconsistent. The kinetics phaseseparation rate decreases, while the thermodynamics parameters, cloud points Tc and delay time tD of isothermal phaseseparation also decrease, and the variation amplitude depends on the matrix composition. The affinity of clay to PMMA results in the composition difference between the border layer and the polymer matrix and further causes the concentration fluctuation at the early stage of phase separation to reduce Tc and tD. On the other hand, the decrease of phase-separation rate is caused by the mechanical barrier effect of clay on the macromolecular diffusion of blend matrix. Hence, such seemingly counterintuitive results on the thermodynamics and kinetics of phase-separation are attributed to different dominant factors.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride) (PVDF)/poly(methylmethacrylate) (PMMA)/poly(styrene-<Emphasis Type="Italic">co</Emphasis>-acrylonitrile) (SAN) ternary blends

Compatibilization of the partially miscible poly(vinylidene fluoride) (PVDF)/poly(styrene-co-acrylonitrile) (SAN) pair by a third homopolymer, i.e., poly(methyl methacrylate) (PMMA), was investigated in relation to cross section morphology, crystallization behaviors and hydrophilicity of the polyblends. Scanning electron microscopy showed a more regular and homogeneous morphology when more than 15 wt.% PMMA was incorporated. The samples presented only α phase regardless of PMMA content in the blend. As the PMMA content increased in the blends, the interactions between each component were enhanced, and the crystallization of PVDF was limited, leading to a decreasing of the crystallinity and the crystallite thickness. Besides, the hydrophilicity of PVDF was further improved by PMMA addition. The sample containing 15 wt.% PMMA showed a more hydrophilic property due to the more polar part of surface tension induced by PMMA addition. Observed from the cross section of the blends, the miscibility of partially miscible PVDF/SAN blends were efficiently improved by PMMA incorporation.     

Effects of organoclays on morphology and thermal and rheological properties of polystyrene and poly(methyl methacrylate) blends

Morphology, thermal and rheological properties of polymer‐organoclay composites prepared by melt‐blending of polystyrene (PS), poly(methyl methacrylate) (PMMA), and PS/PMMA blends with Cloisite® organoclays were examined by transmission electron microscopy, small‐angle X‐ray scattering, secondary ion mass spectroscopy, differential scanning calorimetry, and rheological techniques. Organoclay particles were finely dispersed and predominantly delaminated in PMMA‐clay composites, whereas organoclays formed micrometer‐sized aggregates in PS‐clay composites. In PS/PMMA blends, the majority of clay particles was concentrated in the PMMA phase and in the interfacial region between PS and PMMA. Although incompatible PS/PMMA blends remained phase‐separated after being melt‐blended with organoclays, the addition of organoclays resulted in a drastic reduction in the average microdomain sizes (from 1–1.5 μm to ca. 300–500 nm), indicating that organoclays partially compatibilized the immiscible PS/PMMA blends. The effect of surfactant (di‐methyl di‐octadecyl‐ammonia chloride), used in the preparation of organoclays, on the PS/PMMA miscibility was also investigated. The free surfactant was more compatible with PMMA than with PS; the surfactant was concentrated in PMMA and in the interfacial region of the blends. The microdomain size reduction resulting from the addition of organoclays was definitely more significant than that caused by adding the same amount of free surfactant without clay. The effect of organoclays on the rheological properties was insignificant in all tested systems, suggesting weak interactions between the clay particles and the polymer matrix. In the PS system, PMMA, and organoclay the extent of clay exfoliation and the resultant properties are controlled by the compatibility between the polymer matrix and the surfactant rather than by interactions between the polymer and the clay surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 44–54, 2003     

聚甲基丙烯酸甲酯/苯乙烯-丙烯腈无规共聚物薄膜表面原位原子力显微镜相图

采用原位原子力显微镜在线跟踪方法,研究了聚甲基丙烯酸甲酯/苯乙烯 丙烯腈无规共聚物共混体系表面相分离行为,得到了具有下临界共溶温度（临界温度约为175 ℃）原位相图。 与文献报道的用离位方法所得结果的主要差别是原位的临界相分离温度稍有提高,以及离位结果中存在的组成对称性。 这些差别主要来源于离位和原位实验方法上的差别,薄膜厚度减小导致的相容性,热力学历史的变化以及基底效应的加剧。     

Shear flow effect on phase behavior and morphology in polymer blends

The effect of simple shear flow on the phase behavior and morphology was investigated for both polystyrene/poly(vinyl methyl ether) (PS/PVME) and poly(methyl methacrylate)/poly(styrene‐co‐acrylonitrile) (PMMA /SAN‐29.5) blends, which have LCST (lower critical solution temperature)‐type phase diagram. The measurements were carried out using a special shear apparatus of two parallel glass plates type. The PS/PVME blends showed shear‐induced demixing and shear‐induced mixing at low and high shear rate values, respectively. In addition, the rotation speed and the sample thickness were found to have a pronounced effect on the phase behavior under shear flow. On the‐other hand, PMMA/SAN blend showed only shear‐induced mixing and the magnitudes of the elevation of the cloud points were found to be composition and molecular weight dependent. The morphology of the PMMA/SAN=75/25 blend indicated that shear‐induced mixing occurred at a critical shear rate value, below which the two phases were highly oriented and elongated in the flow direction.     

Noncovalent functionalization of multiwalled carbon nanotubes using graft copolymer with naphthalene and its application as a reinforcing filler for poly(styrene‐co‐acrylonitrile)

A new compatibilizer, poly(vinyl benzyloxy ethyl naphthalene)‐graft‐poly(methyl methacrylate), for poly(styrene‐co‐acrylonirile) (SAN)/multi‐walled carbon nanotubes (MWCNTs) composites was synthesized. It has been identified that naphthalene unit in backbone of compatibilizer interacts with MWCNTs via π? π interaction and that the PMMA graft of the compatibilizer is miscible with the SAN matrix. When a small amount of compatibilizer was added to SAN/MWCNT composites, MWCNTs were more homogeneously dispersed in SAN matrix than the case without compatibilizer, indicating that the compatibilizer improves the compatibility between SAN and MWCNTs. As a consequence, mechanical and electrical properties of the composites with compatibilizer were largely improved as compared with those of composites without compatibilizer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4184–4191, 2010     

Competition of phase dissolution and crystallization in poly(ε-caprolactone)/poly(styrene-co-acrylonitrile) blend

Blend of poly(ε-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN) containing 27.5 wt% of acrylonitrile was studied. The PCL/SAN blend having LCST (lower critical solution temperature) phase boundary above the melting point T_m of PCL offered an excellent opportunity to investigate the competition of liquid-solid phase transition (crystallization) and liquid-liquid phase transition (phase dissolution). A blend with the critical composition (80/20 PCL/SAN) underwent a temperature-jump above LCST to proceed spinodal decomposition, yielding a regularly phase-separated structure (SD structure). Then, it was quenched to the temperatures below T_m at which both the crystallization and the phase dissolution could occur. By transmission electron microscopy it was found that during isothermal annealing after quenching to high temperatures close to T_m (e.g. 51 °C), the SD structure gradually disappeared, and then the crystallization started from a single-phase mixture to yield normal crystalline structure similar to that of a neat crystalline polymer. At lower temperatures (e.g. 40 °C), crystallization quickly occurred and the SD structure was preserved, implying that the crystallization prevailed over the dissolution yielding a bi-continuous structure consisting of amorphous (SAN-rich) and crystalline (PCL-rich) regions. At intermediate temperatures (e.g. 45 °C), the phase dissolution competed with the crystallization, resulting in a bi-continuous structure with longer periodic distance and a broad boundary having a gradient in composition of amorphous region between PCL crystal lamellae. Light-scattering analysis quantitatively revealed a competition of the crystallization and the phase dissolution in terms of the crystallization rate (from H_v scattering) and the apparent diffusion coefficient for dissolution (from V_v scattering).     

Investigation of polymer miscibility by spectroscopic methods. III. Labeling of poly(vinyl chloride), poly(methyl methacrylate) and poly(styrene-co-acrylonitrile) with fluorescent chromophores for nonradiative energy transfer studies

Poly(vinyl chloride) (PVC) is generally recognized as miscible with s.poly(methyl methacrylate) (s.PMMA), poly(?-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) copolymer (SAN) containing 27 wt % AN. Nonradiative energy transfer (NRET) is a very sensitive technique in the investigation of the polymer miscibility. To compare by NRET the actual degree of miscibility of the PVC/s.PMMA, PVC/PCL, and PVC/SAN polymer pairs, each polymer is to be labeled with a fluorescent chromophore to an extent of 1 or 2 mol %. This paper reports efficient pathways to attach anthracene (acceptor) or naphthalene (donor) onto preformed PVC, s.PMMA, and SAN samples. All the attempts for grafting carbazole (donor) moieties have failed, as well as any labeling of PCL whatever the nature of the chromophore.     

Thermal degradation studies in poly(vinyl chloride)/poly(methyl methacrylate) blends

The miscibility, morphology, and thermal properties of poly(vinyl chloride) (PVC) blends with different concentrations of poly(methyl methacylate) (PMMA) have been studied. The interaction between the phases was studied by FTIR and by measuring the glass transition temperature (T_g) of the blends using differential scanning calorimetry. Distribution of the phases at different compositions was studied through scanning electron microscopy. The FTIR and SEM results show little interaction and gross phase separation. The thermogravimetric studies on these blends were carried out under inert atmosphere from ambient to 800 °C at different heating rates varying from 2.5 to 20 °C/min. The thermal decomposition temperatures of the first and second stage of degradation in PVC in the presence of PMMA were higher than the pure. The stabilization effect on PVC was found most significant with 10 wt% PMMA content in the PVC matrix. These results agree with the isothermal degradation studies using dehydrochlorination and UV-vis spectroscopic results carried out on these blends. Using multiple heating rate kinetics the activation energies of the degradation process in PVC and its blends have been reported.     

Mechanical behavior of polymer microlayers

The mechanical behavior of polycarbonate (PC) coextruded as microlayers with a brittle polymer, either poly(styrene-co-acrylonitrile) (SAN) or poly(methyl methacrylate) (PMMA), was examined. Adhesion between layers was measured with the T-peel method. The much higher interfacial toughness of PC/PMMA microlayers compared to PC/SAN was attributed to partial miscibility. Comparison of the microdeformation behavior of 32-layer PC/SAN and PC/PMMA microlayers revealed that very good adhesion between PC and PMMA constrained yielding of the PC. This was seen in the tensile stress-strain curves as a broader stress drop at the yield point and a lower fracture strain. Decreasing the layer thickness by increasing the number of layers enhanced the ductility of both PC/SAN and PC/PMMA microlayers. A PC/PMMA microlayer with 4096 layers and a composition of 80% PC achieved the ballistic performance of polycarbonate.     

Selective solvent annealing induced phase separation and dewetting in PMMA/SAN blend ultrathin films

Phase behaviors induced by solvent annealing in poly(methyl methacrylate) (PMMA) and poly(styrene‐ran‐acrylonitrile) (SAN) blend ultrathin films have been investigated by atomic force microscopy and grazing incidence small‐angle X‐ray scattering. Our results indicate that both the phase separation within the blend and the dewetting of the film induced by composition fluctuation take place upon the selective solvent annealing, producing complex structures containing upper droplets (of one phase) and mimic‐films (of the other rich‐phase). The use of acetic acid (the selective solvent for PMMA) generates PMMA mimic‐film and SAN droplets, while the introduction of DMF (exhibiting better solubility for SAN) vapor results in the formation of SAN mimic‐film and PMMA droplets. Essentially, the interaction at polymer/substrate interface, resultant wettability of selected component, solubility of PMMA and SAN in adopted solvent dominate not only the phase separation and the dewetting of the whole film but also the synergism of them. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1243–1251     

Ternary blends of phenoxy/SAN/poly(-ε-caprolactone)

The compatibilizing effect of poly(ε-caprolactone) (PCL) on the blends of two immiscible polymers, poly(hydroxy ether of bisphenol A) (phenoxy) and poly(styrene-co-acrylonitrile) (SAN) has been investigated. The phase behavior of the ternary blends was affected by the AN content in the SAN copolymers and a maximum miscible region was observed at 19.5 wt % of AN. The effect of AN content on the phase behavior of the ternary blends was interpreted in terms of the relative magnitude of the segmental interaction energy densities, which were obtained by combining a melting point depression and an extended binary interaction model. When a small amount of PCL was added to the phenoxy/SAN blends, the phase morphology showed a finer phase dispersion, indicating that the interfacial tension between the phenoxy and SAN is considerably reduced. However, the improvement in tensile properties was limited despite the morphological change with the PCL content. From the results of the DSC measurements, SEM, and tensile testing, it was understood that the PCL acted as a compatibilizer for the immiscible phenoxy/SAN blends. © 1994 John Wiley & Sons, Inc.     

Methyl methacrylate oligomerically-modified clay and its poly(methyl methacrylate) nanocomposites

A methyl methacrylate oligomerically-modified clay was used to prepare poly(methyl methacrylate) clay nanocomposites by melt blending and the effect of the clay loading level on the modified clay and corresponding nanocomposite was studied. These nanocomposites were characterized by X-ray diffraction, transmission electron microscopy, thermogravimetric analysis and cone calorimetry. The results show a mixed intercalated/delaminated morphology with good nanodispersion. The compatibility between the methylacrylate-subsituted clay and poly(methyl methacrylate) (PMMA) are greatly improved compared to other oligomerically-modified clays.     

STUDY ON PHASE-SEPARATION OF PMMA/SAN BLENDS INDUCED BY GLASS BEADS THROUGH DYNAMIC RHEOLOGICAL MEASUREMENTS

Based on the premise that the addition of glass beads （GB） could hardly influence the linear viscoelasticity in low frequency （ω） region for homogeneous polymer systems, the dynamic rheological behaviors of unfilled and filled poly（methyl methyacrylate） （PMMA）/poly（styrene-co-acrylonitrile） （SAN） blends were studied in order to explore the effect of GB on the phase-separation of binary polymer matrix. Results show that GB has an induced effect on the phase-separation, which embodies that the phase-separation temperature （Ts） of PMMA/SAN blend filled with GB is lower than that of the unfilled system. The higher content of GB, the higher is the ＂secondary plateau＂ of ω in the terminal region of storage modulus （G＇） versus ω plot. The ＂secondary plateau＂ appearing in the terminal region is attributed to the phase-separation of PMMA/SAN blends and it becomes more fiat for filled polymer blends under the same conditions. However, it is suggested that this kind of ＂induced effect＂ is related to the GB content; the higher content of GB particles might enhance the interaction between the particles and polymer matrix. Moreover, it is found that the addition of GB also has an influence more or less on the morphology and domain size of polymer matrix. It is believed that the plot of dynamic viscosity （η＇） versus the loss viscosity （η＂） is sensitive to examine the effect induced by GB on the phase-separation of binary polymer matrix.     

High Resolution Tip Enhanced Raman Mapping on Polymer Thin Films

Advanced tip enhanced Raman mapping (TERM) was applied to high resolution chemical identification on nanoscale. Thin poly(methyl methacrylate)/poly(styrene acrylonitrile) (SAN28/PMMA) blend films were measured at different stages of phase separation. New insights into the phase evolution behavior of the thin films were obtained, when the TERM images were compared. An unexpected morphology transition was observed after a few minutes annealing at 250 °C. No surface enrichment of PMMA was observed, differing from the previous reports on a similar well-studied system of SAN33/PMMA. The glass transition temperature, the surface and interfacial tension were found to be the main factors responsible for the phase evolution behavior of SAN28/PMMA films.     

Transition from miscibility to immiscibility in blends of poly(methyl methacrylate) and styrene-acrylonitrile copolymers with varying copolymer composition: a DSC study

The glass transition and the structural relaxation processes have been studied in blends of poly(methyl methacrylate) (PMMA) and styrene-acrylonitrile (SAN) copolymers with different acrylonitrile (AN) contents. The 50/50 wt.% blend of PMMA with the SAN copolymer containing 30 wt.% of AN is immiscible, while blends with copolymers containing between 13 and 26 wt.% of AN are miscible. Thus the upper limit of miscibility is between 26 and 30 wt.% of AN. The temperature dependence of the relaxation times of the conformational rearrangements of polymer chains around the glass transition have been determined in the blends and pure components by modelling DSC thermograms obtained after different thermal histories in each sample. The slope in the Arrhenius diagram logτ vs 1/T around the glass transition temperature is significantly smaller in the blend which is closer to the upper limit of miscibility than in the other miscible blends in which SAN copolymer contains less AN. The change of slope can be ascribed to a distribution in the glass transition temperatures of the different rearranging regions, reflecting the appearance of a microheterogeneity in the blend that cannot be detected as a double glass transition in the blend.     

Upper critical solution temperature type phase behavior of poly(styrene‐co‐acrylonitrile) blends with poly(styrene‐co‐n‐phenyl maleimide) and their interaction energies

To enhance the heat resistance of poly(styrene‐co‐acrylonitrile‐co‐butadiene), ABS, miscibility of poly(styrene‐co‐acrylonitrile), SAN, with poly(styrene‐co‐n‐phenyl maleimide), SNPMI, having a higher glass transition temperature than SAN was explored. SAN/SNPMI blends casted from solvent were immiscible regardless of copolymer compositions. However, SNPMI copolymer forms homogeneous mixtures with SAN copolymer within specific ranges of copolymer composition upon heating caused by upper critical solution temperature, UCST, type phase behavior. Since immiscibility of solvent casting samples can be driven by solvent effects even though SAN/SNPMI blends are miscible, UCST‐type phase behavior was confirmed by exploring phase reversibility. When copolymer composition of SNPMI was fixed, the phase homogenization temperature of SAN/SNPMI blends was increased as AN content in SAN copolymer increased. To understand the observed phase behavior of SAN/SNPMI blend, interaction energies of blends were calculated from the UCST‐type phase boundaries by using the lattice‐fluid theory combined with a binary interaction model. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1131–1139, 2008     

Effects of poly(methyl methacrylate)-block-poly(vinyl acetate) copolymer on the spinodal decomposition of corresponding homopolymer blends

Effects of adding a small amount of poly(methyl methacrylate)-block-poly(vinyl acetate) (PMMA-b-PVAc) to poly(methyl methacrylate)/poly(vinyl acetate) (PMMA/PVAc) blends with a lower critical solution temperature (LCST) phase diagram on the kinetics of late-stage spinodal decomposition (SD) were investigated by time-resolved light scattering at 160°C. It is found that the coarsening process of the structure was slowed down or accelerated upon addition of PMMA-b-PVAc depending on the composition of the block copolymer and the blend. The effect of the block copolymer on the domain size were interpreted as compatibilizing and incompatibilizing effects of the block copolymer on PMMA/PVAc blends based on the evaluation of changes in the stability limits of PMMA/PVAc with the addition of block copolymer using random phase approximation (RPA).     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.