聚合物波导型表面等离子体共振传感器的特性研究

基于表面等离子体共振理论,将SU-8作为波导芯层材料,以聚甲基丙烯酸甲酯(PMMA)为下包层材料,设计了一款聚合物波导型SPR传感器。理论计算了波导芯层折射率、被测物折射率、不同金属薄膜及其厚度等因素对表面等离子体共振曲线的影响。分析结果表明,在可测试范围内,被测物折射率越大,灵敏度越高;波导芯层折射率减小,共振峰向长波方向移动,被测物检测范围整体向折射率小的方向偏移,波导芯层折射率增大则相反。     

基于Au/ITO纳米复合材料的自参照SPR传感器

利用Au/ITO纳米复合材料设计了一种自参照表面等离子体共振传感器.该传感器产生的光谱有两个共振峰,即共振峰1和共振峰2.共振峰1随着待测介质折射率和入射角的变化产生漂移,而共振峰2仅随入射角的变化产生漂移,两个共振峰相互参照,降低了入射角偏移对测量结果的影响,提高了测量的准确性.在纳米复合材料的4种不同体积分数下,仿真分析了入射角、待测介质折射率和薄膜厚度变化对两个共振波长的影响.在入射角θ为80°,且金的体积分数f为0.65,薄膜厚度d为40nm和45nm,或金的体积分数f为0.85,薄膜厚度d为45nm和50nm时,共振峰2不随待测介质折射率的变化而变化,只有共振峰1随待测介质折射率的变化而变化,达到自参照传感器的理想状态.     

金纳米球壳对的局域表面等离激元共振特性分析

应用有限元方法, 研究金纳米球壳对的几何结构参数及物理参量对其表面等离激元共振的散射及消光光谱的影响, 并根据等离激元杂化理论进行了理论分析. 结果表明, 随着金壳厚度的增加, 金纳米球壳对的散射及消光共振峰先发生蓝移而后红移, 而随着金纳米球壳间隙的减小, 或者随着金纳米球壳的内核尺寸或内核介质折射率的增大, 散射及消光共振峰均发生红移; 随着金壳厚度或内核尺寸减小, 或者随着内核介质折射率增大, 金纳米球壳对的散射与消光共振强度减弱, 而随着金壳间隙的减小, 金纳米球壳对的散射共振强度先增强后减弱, 而消光共振强度逐渐增强, 数值模拟与理论分析一致.     

金属纳米颗粒光学性质的离散偶极近似计算

采用离散偶极子近似(DDA)方法,研究了单体银纳米粒子和银纳米粒子阵列的光谱特性。研究结果发现,单体银纳米粒子的表面等离子体共振消光峰的位置随着周围介质折射率和粒子尺寸的增大逐渐红移,并且消光光谱的峰宽也越来越大。当银纳米粒子正方阵列的周期接近单体的共振波长时,阵列的消光光谱中会出现尖锐的共振峰,改变粒子尺寸的大小可以发现消光光谱中共振峰的峰值和位置有大幅度地改变,通过改变阵列在平行和垂直于入射光偏振方向上的周期,可以调节二维长方阵列共振峰的峰宽和峰位。该研究为纳米粒子在光学显微镜、生物传感元件、数据存储等领域中的应用提供有效地理论参考。     

金属复合纳米粒子的局域表面等离子体特性研究

提出了一种在银层上面覆盖一层金的四棱台复合纳米结构。采用离散偶极子近似(DDA)方法,针对光激发复合金属纳米粒子的局域表面等离子体共振(LSPR)进行研究,讨论了四棱台纳米粒子金银复合结构在不同尺寸、不同混合比等条件下的消光特性及折射率灵敏度。计算结果显示,在银层厚度为50 nm的四棱台纳米粒子上覆盖金层,其折射率灵敏度不变。同时,四棱台银纳米粒子厚度的增加会使其消光峰值波长蓝移。金材料比例的增加会使金银复合纳米结构的消光峰值波长红移。当金银复合结构的纳米粒子的厚度大于自由电子的平均自由程时,其局域表面等离子体激发强度不发生变化。     

基于侧边抛磨光纤表面等离子体共振的折射率和温度传感研究

用轮式侧边抛磨法制作侧边抛磨光纤,通过磁控溅射法溅射金膜制成侧边抛磨光纤表面等离子体共振(SPR)传感器,并通过理论和实验对传感器的折射率灵敏度以及温度特性做了深入研究。结果表明表面等离子体共振波长随待测样品折射率的增大向长波长方向漂移,平均折射率灵敏度为4.1×103 nm/RIU(RIU为单位折射率),高于已报道的结果;共振波长随待测样品温度的升高向短波长方向漂移,平均温度灵敏度为0.36nm/℃,故该光纤SPR传感器具有更强抗温度漂移能力和更高的高折射率灵敏度,其在生物化学传感领域有重要的应用。     

基于U型结构的单模光纤SPR折射率传感器

设计了一种基于U型结构的单模光纤表面等离子体共振折射率传感器,采用在移除部分包层并弯曲成U型固定后的单模光纤表面镀金纳米层和TiO2调制层的方式,实现表面等离子体共振的激发.利用有限元仿真软件COMSOL Multiphysics,研究了不同弯曲半径和TiO2调制层厚度对传感性能的影响.通过对四种弯曲半径(R=0.3cm,0.5cm,0.8cm,1cm)的分析,结果表明随着弯曲半径增大,表面等离子体共振信号强度增大且峰值波长有微小的蓝移.在弯曲半径为0.5cm的条件下,研究了TiO2调制层厚度从0变化到40nm对传感器性能的影响,结果表明随着TiO2调制层厚度增大,表面等离子体共振峰峰值波长红移且对外界折射率变化的灵敏度显著增大.在弯曲半径为0.5cm,TiO2调制层厚度为40nm的条件下,传感器在低折射率区(nd=1.333)灵敏度达到了5 959nm/RIU,高折射率区(nd=1.383)灵敏度达到了11 092nm/RIU.与没有调制层的结果相比,灵敏度提高了一倍左右.     

双对称性破缺Au-TiO_2-Ag三层纳米杯的LSPR特性研究

设计了一种双对称性破缺Au-TiO_2-Ag三层纳米杯结构,采用有限元方法分析了其局域表面等离子体共振(Localized Surface Plasmon Resonance,LSPR)特性,并采用等离激元杂化理论对LSPR现象进行理论分析。分别仿真了入射光偏振态、核壳结构参数和外界介质折射率对Au-TiO_2-Ag三层纳米杯消光光谱的影响。研究结果表明,当入射光偏振方向垂直于对称轴方向时,可将反对称横向耦合模式ω-⊥〉1的共振峰波长调谐至近红外区域1100nm附近,同时该模式共振波长随外界介质折射率的增大产生红移,这一特性可在生物传感领域得到广泛的应用。     

金-二氧化钛（Au-TiO_2）复合薄膜的制备及局域表面等离子体共振（LSPR）效应

利用溶胶凝胶法在玻璃衬底上制备了金-二氧化钛（Au-TiO2）复合纳米薄膜,研究了热处理温度对复合薄膜表面纳米颗粒沉积的影响。利用原子力显微镜对样品进行了形貌表征,结果显示：复合薄膜是由纳米微晶组成的致密膜,温度越高越有利于Au粒子的形成。在550℃的热处理温度下,薄膜表面沉积的纳米微晶的粒径约为100nm。利用紫外-可见分光光度计测量了反射谱线,结果表明：由于局域表面等离子体共振（LSPR）的产生,在不同的热处理温度下,第一个反射峰（短波长处）不发生变化,第二个反射峰（长波长处）发生漂移（红移）。     

基于锚形谐振腔的等离子体波导特性研究

基于表面等离子体激元在金属-介质-金属结构中优良的传输特性,设计了一种由直波导和锚形谐振腔组成的波导滤波器。仿真分析了波导滤波器传输特性和电场分布随结构参数和谐振腔内介质折射率变化规律。结果表明,该锚形谐振腔最佳结构时滤波器半峰全宽低至8 nm,品质因数高达121.9。利用共振波长与结构参数变化规律,设计了光通信波长窗口的窄带带阻滤波器。根据SPPs对谐振腔介质折射率敏感的特性,发现透射谱线随折射率变大而发生红移。本文提出的基于锚形谐振腔的等离子体MIM波导滤波器为设计特定波长的窄带带阻滤波器提供了新思路,也为基于谱线红移特性设计的介质折射率传感器提供了技术支持。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.