Crystal polymorphism in electrospun composite nanofibers of poly(vinylidene fluoride) with nanoclay

We investigated for the first time the morphology and crystal polymorphism of electrospun composite nanofibers of poly(vinylidene fluoride) (PVDF) with two nanoclays: Lucentite™ STN and SWN. Both nanoclays are based on the hectorite structure, but STN has organic modifier in between the layers of hectorite while SWN does not. PVDF/nanoclay was dissolved in N,N-dimethylformamide/acetone and electrospun into composite nanofiber mats with fiber diameters ranging from 50-800 nm. Scanning electron microscopy shows that addition of STN and SWN can greatly decrease the number of beads and make the diameter of the nanofibers more uniform due to the increase of electrospinning solution conductivity brought by the nanoclay. Infrared spectroscopy and X-ray diffraction confirm that both STN and SWN can induce more extended PVDF chain conformers, found in beta and gamma phase, while reducing the alpha phase conformers in electrospun PVDF/Nanoclay composite nanofibers. With the attached organic modifier, even a small amount of STN can totally eliminate the non-polar alpha crystal conformers while SWN cannot. The ionic organic modifier makes STN much more effective than SWN in causing crystallization of the polar beta and gamma phases of PVDF. An ion-dipole interaction mechanism, suggested by Ramasundaram, et al. is utilized to explain the crystal polymorphism behavior in electrospun PVDF/nanoclay composite nanofibers.     

Miscibility and morphology of poly(vinylidene fluoride)/poly[(vinylidene fluoride)‐ran‐trifluorethylene] blends

This study presents an investigation of the effect of the different crystalline phases of each blend component on miscibility when blending poly(vinylidene fluoride) (PVDF) and its copolymer poly[(vinylidene fluoride)‐ran‐trifluorethylene] [P(VDF–TrFE)] containing 72 mol % of VDF. It was found that, when both components crystallized in their ferroelectric phase, the PVDF showed a strong effect on the crystallinity and phase‐transition temperature of the copolymer, indicating partial miscibility in the crystalline state. On the other hand, immiscibility was observed when both components, after melting, were crystallized in their paraelectric phase. In this case, however, a decrease in crystallization temperatures suggested a strong interaction between monomers in the liquid state. Blend morphologies indicated that, in spite of the lack of miscibility in the crystalline state, there is at least miscibility between PVDF and P(VDF–TrFE) in the liquid state, and that a very intimate mixture of the two phases on the lamellar level can be maintained upon crystallization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1362–1369, 2002     

Viscoelastic and pressure–volume–temperature properties of poly(vinylidene fluoride) and poly(vinylidene fluoride)–hexafluoropropylene copolymers

The relationship between the pressure, volume, and temperature (PVT) of poly(vinylidene fluoride) homopolymers (PVDF) and poly(vinylidene fluoride)–hexafluoropropylene (PVDF–HFP) copolymers was determined in the pressure range of 200–1200 bar and in the temperature range of 40°C–230°C. The specific volume was measured for two homopolymers having a molecular weight (M_w) of 160,000–400,000 Da and three copolymers containing between 3 and 11 wt % HFP with a molecular weight range of 320,000–480,000 Da. Differential scanning calorimetry (DSC) was used to simulate the cooling process of the PVT experiments and to determine the crystallization temperature at atmospheric pressure. The obtained results were compared to the transitions observed during the PVT measurements, which were found to be pressure dependent. The results showed that the specific volume of PVDF varies between 0.57 and 0.69 cm³/g at atmospheric pressure, while at high pressure (1200 bar) it varies between 0.55 and 0.64 cm³/g. For the copolymers, the addition of HFP lowered its melting point, while the specific volume did not show a significant change. The TAIT state equation describing the dependence of specific volume on the zero‐pressure volume (V₀,T), pressure, and temperature has been used to predict the specific volume of PVDF and PVDF–HFP copolymers. The experimental data was fitted with the state equation by varying the parameters in the equation. The use of the universal constant, C (0.0894), and as a variable did not affect the predictions significantly. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 230–241, 2001     

Spatio-temporal growth of broken spiral and concentric ringed spherulites in blends of poly(vinylidene fluoride) and ethylene-vinylacetate copolymers

Melting and crystallization behavior in mixtures of poly(vinylidene fluoride) (PVDF) and several ethylene-vinyl acetate copolymers (EVAc) with various ethylene contents have been investigated by means of differential scanning calorimetry, atomic force microscope, and optical microscopy. PVDF/EVAc-80 exhibits the melting point depression of PVDF crystals, suggestive of a miscible character of the pair. Crystallization behavior and morphology development in blends of PVDF/EVAc-80 have been investigated with an emphasis on the spherulitic growth demonstrating the spiral and concentric ringed (or target) patterns. Of particular interest is the break-up of the spiral or concentric ringed patterns at very shallow supercoolings, which may be attributed to instabilities driven by the exclusion of amorphous PVDF and EVAc chains into the emerging inter- and intra-spiral (or target) lamellar regions.     

Counterion dependent crystallization kinetics in blends of a perfluorosulfonate ionomer with poly(vinylidene fluoride)

Blends of poly(vinylidene fluoride) (PVDF) with a perfluorosulfonate ionomer, Nafion^®, have been prepared and examined in terms of the crystallization kinetics of the PVDF component. In blends of PVDF with Na⁺-form Nafion^®, the rates of bulk crystallization, as observed by DSC, and the spherulitic growth rates of the PVDF component, as observed using optical microscopy, were found to be very similar to that of pure PVDF. This behavior was attributed to the course phase separation of Na⁺-form Nafion^® from PVDF and melt incompatibility of the physically cross-linked ionomer with the crystallizable component. In this segregated state, the PVDF component of the blend is allowed to crystallize in pure phases that are isolated under the influence of Nafion^®. In contrast, when the ionomer was exchanged with more weakly interacting quaternary alkylammonium counterions, a decrease in both the rate of bulk crystallization and spherulitic growth was observed. Furthermore, the crystallization kinetics of PVDF in these blends was found to be dependent on the counterion size; as the size of counterions associated with the Nafion^® component increased, the rate of crystallization decreased. This behavior was attributed to a weakening of the electrostatic interactions in the ionomer phase and thus an increase in the extent of phase mixing with the larger ions.     

Morphology, polymorphism behavior and molecular orientation of electrospun poly(vinylidene fluoride) fibers

The morphology, polymorphism behavior and molecular orientation of electrospun poly(vinylidene fluoride) (PVDF) fibers have been investigated. We found that electrospinning of PVDF from its N,N-dimethylformamide/acetone solutions led to the formation of β-phase. In contrast, only α- and γ-phase was detected in the spin-coated samples from the same solutions. In the aligned electrospun PVDF fibers obtained using a rotating disk collector, the β-phase crystallites had a preferred orientation along the fiber axis. The degree of orientation did not, however, vary significantly with the speed of the rotation disk collector, and the β-phase was also not significantly enhanced with the increase in the rotation speed or the decrease in the size of spinnerets. These facts indicated that the orientation was likely to be caused by Columbic force rather than the mechanical and shear forces exerted by the rotating disk collector and spinnerets. The Columbic force may induce local conformational change to straighter TTTT conformation, and hence promote the β-phase. The addition of 3 wt.% of tetrabutylammonium chloride (TBAC) into the polymer solutions effectively improved the morphology of the electrospun fibers, and led to almost pure β-phase in the fibers. With spin coating, PVDF-TBAC did not, however, show any strong β-phase diffraction peak. The synergistic β-enhancement effect of TBAC and electrospinning is possibly due to the fact that while TBAC could induce more trans conformers, electrospinning promotes parallel packing, and hence inter-chain registration.     

Preparation of antifouling ultrafiltration membranes from copolymers of polysulfone and zwitterionic poly(arylene ether sulfone)s

The past few decades have witnessed rapid gains in our demands of antifouling membranes such as water purification membranes and hemodialysis membranes. A variety of methodologies have been proposed for improving the antifouling performance and the hemocompatibility of the membranes. In this study, a series of copolymers (PSF-PESSB) containing polysulfone (PSF) and poly(arylene ether sulfone) bearing pendant zwitterionic sulfobetaine groups (PESSB) were prepared via one-pot polycondensation. Subsequently, the ultrafiltration (UF) membranes were prepared from different zwitterion-containing copolymers. The prepared membranes showed high thermal stability and mechanical properties. Besides, it also displayed attractive antifouling performance and blood compatibility. Compared with the original PSF membrane, the amount of protein absorption on the modified membrane was reduced; the flux recovery ratio and the resistance to blood cells were significantly improved. The results of this work suggest that PSF-PESSB membranes are expected to be applied in blood purification. The introduction of zwitterion-containing polymers to membranes paves ways for developing advanced hemodialysis technologies for crucial process.     

Weak interaction,marginal miscibility,and ring‐band spherulites in blends of poly(vinylidene fluoride) with polyesters

Fourier transform infrared (FTIR) spectroscopy, optical microscopy (OM), and differential scanning calorimetry (DSC) techniques were used to probe phase behavior and interactions in blends of poly(vinylidene fluoride) (PVDF) and polyesters [poly(trimethylene adipate) (PTA) and poly(pentamethylene adipate) (PPA)] of relatively low crystallizability. DSC thermal analysis and OM characterization proved that PVDF was miscible with PTA and PPA with a low lower critical solution temperature. Small negative values of the interaction parameters (χ₁₂ = ?0.13 for a PVDF/PPA blend) were obtained with the melting‐point depression method. FTIR spectroscopy results revealed that interactions between ? CF₂ of PVDF and the ? C?O group of the polyester were weak, in agreement with the thermal analysis results. An increase in the coarseness and/or ring‐band spacing further provided supportive evidence that miscibility did exist between the polyester and PVDF constituents in the blends. Pattern changes in ring‐band spherulites of the miscible blends further substantiated the favorable, though weak, interactions between the PVDF and polyester constituents. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(vinylidene fluoride) hollow‐fiber membranes containing silver/graphene oxide dope with excellent filtration performance

In this study, an antifouling poly(vinylidene fluoride) (PVDF) hollow‐fiber membrane was fabricated by blending with silver‐loaded graphene oxide via phase inversion through a dry‐jet, wet‐spinning technique. The presence of graphene oxide endowed the blended membrane with a high antifouling ability for organic fouling. The permeation fluxes of the blended membrane was 3.3 and 2.9 times higher than those of a pristine PVDF membrane for filtering feed water containing protein and normal organic matter, respectively. On the other hand, the presence of silver improved the antibiofouling capability of the blended membrane. For the treatment of Escherichia coli suspension, the permeation flux of the blended membranes was 8.2 times as high as that of the pristine PVDF membrane. Additionally, the presented blended membrane improved the hydrophilicity and mechanical strength compared to those of the pristine PVDF membrane, with the water contact angle decreasing from 86.1 to 62.5° and the tensile strength increasing from 1.94 to 2.13 MPa. This study opens an avenue for the fabrication of membranes with high permeabilities and antifouling abilities through the blending of graphene‐based materials for water treatment. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44713.     

Compatibilization of immiscible nylon 6/poly(vinylidene fluoride) blends using graphene oxides

A new strategy to compatibilize immiscible blends is proposed, using graphene oxide (GO) nanosheets taking advantage of their unique amphiphilic structures. When 0.5 or 1 wt% GOs were incorporated in immiscible nylon 6/poly(vinylidene fluoride) (PVDF) (90/10 wt%) blends, the dimension of PVDF dispersed particles was markedly reduced and became more uniform, revealing a well‐defined compatibilization effect of GOs on the immiscible blends. Correspondingly, the ductility of the compatibilized blends increased several times compared with uncompatibilized immiscible blends. In order to explore the underlying compatibilization mechanism, Fourier transform infrared and Raman spectra were applied to suggest that the edge polar groups of GOs can form hydrogen bonds with nylon 6 while the basal plane of GOs can interact with electron‐withdrawing fluorine on PVDF chains leading to the so‐called charge‐transfer C–F bonding. In this case, GOs exhibit favorable interactions with both nylon 6 and PVDF phase, therefore stabilizing the interface during GO migrations from PVDF/GO masterbatch to nylon 6 phase, which can minimize the interfacial tension and finally lead to compatibilization effects. Obviously, this work may open a broad prospect for GOs to be widely applied as a new compatibilizer in industrial fields. © 2012 Society of Chemical Industry     

Insight into fouling behavior of poly(vinylidene fluoride) (PVDF) hollow fiber membranes caused by dextran with different pore size distributions

Membrane fouling is the key problem that occurs in membrane process for water treatment. However, how membrane microstructure influences the fouling behavior is still not clear. In this study, fouling behavior caused by dextran was deeply and systematically investigated by employing four poly(vinylidene fluoride)(PVDF)membranes with different pore sizes, ranging from 24 to 94 nm. The extent of fouling by dextran was accurately characterized by pore reduction, flux decline, and the change of critical flux. The result shows that membrane with the smallest pore size of 24 nm experienced the smallest fouling rate and the lowest fouling extent. As the membrane pore size increased, the critical flux ranges were 105-114, 63-73, 38-44 and 34-43 L·m~(-2)·h~(-1),respectively. The critical flux and fouling resistances indicated that the fouling propensity increases with the increase of membrane pore size. Two pilot membrane modules with mean pore size of 25 nm and 60 nm were applied in membrane filtration of surface water treatment. The results showed that serious irreversible membrane fouling occurred on the membrane with pore size of 60 nm at the permeate flux of40.5 L·m~(-2)·h~(-1).On the other hand, membrane with pore size of 25 nm exhibited much better anti-fouling performance when permeate flux was set to 40.5,48 and 60 L·m~(-2)·h~(-1).     

Antifouling microfiltration membranes prepared from poly(vinylidene fluoride)‐graft‐Poly(N‐ vinyl pyrrolidone) powders synthesized via pre‐irradiation induced graft polymerization

Poly(vinylidene fluoride) (PVDF) powders were grafted with N‐vinyl pyrrolidone using the pre‐irradiation induced graft polymerization technique. The effects of reaction time, absorbed dose, and monomer concentration on the degree of grafting were investigated, and the grafted PVDF powders were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The grafted PVDF powders were also cast into microfiltration (MF) membranes via the phase‐inversion method. The contact angle and water uptake were measured. The membrane morphology was studied by scanning electron microscopy, and the water filtration properties of the membranes were tested. The antifouling properties were determined through measurements of the recovery percentage of pure water flux after the MF membranes were fouled with bovine serum albumin solution. The results confirmed that the existence of poly(N‐vinyl pyrrolidone) (PVP) graft chains improved the hydrophilicity and antifouling properties of the MF membranes cast from PVDF‐g‐PVP powders. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Compatibility of poly(vinylidene fluoride) (PVDF)/polyamide 12 (PA12) blends

Poly(vinylidene fluoride) (PVDF)/polyamide 12 (PA12) blends showed new peaks in XRD profile with increasing PA12 and the crystallinity of PA12 significantly decreased with the addition of PVDF. PVDF showed three relaxation regions at about −40, 40, and 100°C, respectively, and glass transition temperature (T_g ) of PA12 increased in blends (10.8→30.14°C) and α‐relaxation of PVDF decreased from 100.26 to 86.46°C. Complex viscosities (η*) vs. composition curve showed a great positive deviation in PVDF‐rich and a small negative deviation in PA12‐rich blends. The N—H and C=O stretching band of PA12 shifted slightly toward higher wavelength, and from curve‐fitted data the area of hydrogen‐bonded C=O stretching bands of PA12 decreased with the addition of PVDF, especially in the 30/70 blend, implying the existence of interactions between the β‐hydrogen atom of PVDF and amide carbonyl group of PA12 in the blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1374–1380, 2000     

Irradiation‐induced grafting of poly(vinylidene fluoride)‐graft‐poly(styrene sulfonic acid) for the preparation of planar and tube‐shaped air‐drying membranes

A novel air‐drying membrane was developed and investigated as an alternative for planar and tube‐shaped drying membranes composed of Nafion^®. The new membrane is based on poly(vinylidene fluoride) (PVDF) polymer types grafted with polystyrene sulfonic acid. Modification of the PVDF membrane by chemical grafting was initiated via γ‐irradiation of pre‐made film and tube‐shaped samples. The grafting was conducted while the pre‐irradiated PVDF samples were immersed in styrene monomer solution. Three unique characterization methods were introduced to evaluate the ion exchange and barrier functions of the membrane. This investigation focuses on optimizing the degree of grafting yield, and subsequently the control of the membrane's overall functional performances, through (1) monitoring the PVDF's degree of crystallinity and (2) monitoring the styrene monomer solution temperature, respectively. Different levels of crystallinity were achieved by melt blending the PVDF‐copolymer with PVDF‐homopolymer, in various mixing ratios. Another variable examined in this investigation was the introduction of an ionic complex on the sulfonic acid end groups, and its effect on the membrane functional performance was studied. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Porous poly(vinylidene fluoride) membrane with highly hydrophobic surface

The preparation of very hydrophobic poly(vinylidene fluoride) (PVDF) membranes was explored by using two methods. The first one was the modified phase inversion method using a water/N,N‐dimethylacetamide (DMAc) mixture instead of pure water as a soft precipitation bath. The second method was a precipitation‐bath free method, that is, the PVDF/DMAc casting solution underwent gelation in the open air instead of being immersed into a precipitation bath. The morphology of the surface and cross section of the membranes was investigated by using scanning electron microscopy (SEM). It was found that the membranes exhibited certain micro‐ and nanoscale hierarchical roughness on the surface, which brought about an enhanced hydrophobicity of the membrane. The contact angle (CA) of the samples obtained by the second method was as high as 150° with water. The conventional phase inversion method preparing PVDF porous membrane using pure water as precipitation bath usually results in an asymmetric membrane with a dense skin layer having a CA close to that of a smooth PVDF surface. The modified approach avoided the formation of a skin‐layer and resulted in a porous and highly hydrophobic surface of PVDF. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1358–1363, 2005     

Effect of surface modifying macromolecules on the properties of poly(vinylidene fluoride) membranes

Poly(vinylidene fluoride) (PVDF) membranes were surface-modified using fluorotelemer intermediate Zonyl BA-L as a fluorinated surface modifying macromolecules (SMM) additives in the concentration range from 0 to 2 wt.%. Prepared membranes were characterized by contact angle measurement, electron spectroscopy for chemical analysis (ESCA), scanning electron microscopy (SEM), and pervaporation test. The experimental results showed that SMM migrated to the surface and effectively increased the surface hydrophobicity of the PVDF membranes. The pure water permeation flux evaluated by pervaporation decreased with an increase in the content of SMM.     

Recognition properties of poly(vinylidene fluoride) hollow‐fiber membranes modified by levofloxacin‐imprinted polymers

Through the use of thermal polymerization, poly(vinylidene fluoride) (PVDF) hollow‐fiber membranes modified by a thin layer of molecularly imprinted polymers (MIPs) were developed for the selective separation of levofloxacin. To demonstrate the changes induced by thermal polymerization, PVDF hollow‐fiber membranes with different modification degrees by repeated polymerization were weighed. The total weight of the imprinted membranes increased by 14 μg/cm² after a five‐cycle polymerization. An increase in the membrane weight indicated the deposition of an MIP layer on the external surface of PVDF hollow‐fiber membranes during each polymerization cycle, which was also characterized by scanning electron microscopy. MIP membranes with different degrees of surface modification provided highly selective binding of levofloxacin. Both hollow‐fiber MIP membranes and nonimprinted membranes showed enhanced adsorption of levofloxacin and ofloxacin gradually with an increase in the modification degrees of PVDF hollow‐fiber membranes to a maximum value followed by a decrease. These results indicate that thermal polymerization indeed produces an MIP layer on the external surface of PVDF hollow‐fiber membranes and that it is feasible to control the permeability by repeated polymerization cycles. Different solvent systems in the permeation experiments were used to understand the hydrophobic interaction as one of the results of the binding specificity of MIP membranes. Selective separation was obtained by multisite binding to the template via ionic, hydrogen‐bond, and hydrophobic interactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Formation of multilayer poly(acrylic acid)/poly(vinylidene fluoride) composite membranes for pervaporation

Dual‐ and multilayer composite membranes, consisting of poly(acrylic acid) (PAA) and poly(vinylidene fluoride) (PVDF), were synthesized by the plasma‐induced polymerization technique. The dual‐layer membrane had a dense PAA layer grafted onto a microporous PVDF substrate, whereas in the multilayer membranes, the grafted PAA and the PVDF layers were arranged in an alternating sequence (e.g., PAA/PVDF/PAA and PAA/PVDF/PAA/PVDF/PAA). These membranes were used in a pervaporation process to separate ethanol–water solutions. For the dual‐layer membranes, the results indicated that the separation factor increased and the permeation flux decreased with increasing amounts of grafted PAA. For the case of grafting yield < 0.6 mg/cm², the composite membrane demonstrated poor separation. As the grafting yield reached 0.85 mg/cm², a sharp increase of the separation factor was observed. For the multilayer membranes, the pervaporation performances were very good, with high separation factors (on the order of 100) and reasonable permeation fluxes over a wide ethanol concentration range. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2266–2274, 2004     

pH‐ and temperature‐sensitive microfiltration membranes from blends of poly(vinylidene fluoride)‐graft‐poly(4‐vinylpyridine) and poly(N‐isopropylacrylamide)

The copolymer poly(vinylidene fluoride)‐graft‐poly(4‐vinylpyridine) (PVDF‐g‐P4VP) was prepared through the graft copolymerization of poly(vinylidene fluoride) with 4‐vinylpyridine. Through the blending of the PVDF‐g‐P4VP copolymer with poly(N‐isopropylacrylamide) (PNIPAm) in an N‐methyl‐2‐pyrrolidone solution, PVDF‐g‐P4VP/PNIPAm membranes were fabricated by phase inversion in aqueous media. Elemental analyses indicated that the blend concentration of PNIPAm in the blend membranes increased with an increase in the blend ratio used in the casting solution. Scanning electron microscopy revealed that the membrane surface tended to corrugate at a low PNIPAm concentration and transformed into a smooth morphology at a high PNIPAm concentration. The surface morphology and pore size distribution of the microfiltration membranes could be regulated by the blend concentration of the casting solution, temperature, pH, and ionic strength of the coagulation bath. X‐ray photoelectron spectroscopy revealed a significant enrichment of PNIPAm on the membrane surface. The flux of aqueous solutions through the blend membranes exhibited a pH‐ and temperature‐dependent behavior. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4089–4097, 2006     

Effect of hot‐press on electrospun poly(vinylidene fluoride) membranes

Poly(vinylidene fluoride) (PVDF) was electrospun into ultrafine fibrous membranes from its solutions in a mixture of N,N‐dimethylformamide and acetone (9:1, v/v). The electrospun membranes were subsequently treated by continuous hot‐press at elevated temperatures up to 155°C. Changes of morphology, crystallinity, porosity, liquid absorption, and mechanical properties of the membranes after hot‐press were investigated. Results of scanning electron microscopy showed that there were no significant changes in fibrous membrane morphology when the hot‐press temperature varied from room temperature to 130°C, but larger pores were formed because of fibers melting and bonding under higher temperatures. Analyses of X‐ray diffraction and differential scanning calorimeter exhibited that the crystalline form of PVDF could transfer from β‐type to α‐type during hot‐press at temperatures higher than 65°C. Tensile tests suggested that the mechanical properties of the electrospun PVDF membranes were remarkably enhanced from 25 to 130°C, whereas the porosity and the liquid absorption decreased. The hot‐press at 130°C was optimal for the electrospun PVDF membranes. The continuous hot‐press post‐treatment could be a feasible method to produce electrospun membranes, not limited to PVDF, with suitable mechanical properties as well as good porosity and liquid absorption for their applications in high‐quality filtrations or battery separators. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers