Hydroelastic responses and drift forces of a very-long floating structure equipped with a pin-connected oscillating-water-column breakwater system

The hydroelastic responses of a very-long floating structure (VLFS) in waves connected to a floating oscillating-water-column (OWC) breakwater system by a pin are analyzed by making use of the modal expansion method in two dimensions. The Bernoulli–Euler beam equation for the VLFS is coupled with the equations of motions of the breakwater taking account of the geometric and dynamic boundary conditions at the pin. The Legendre polynomials are employed as admissible functions representing the assumed modes of the VLFS with pinned-free-boundary conditions. It has been shown numerically that the deflections, bending moments and shear forces of the VLFS in waves can be reduced significantly by a pin-connected OWC breakwater. The time-mean horizontal drift forces of the VLFS equipped with the breakwater calculated by the near-field method are also presented.     

Nonlinear Finite Element Analysis of Ocean Cables

This study has focused on developing numerical procedures for the dynamic nonlinear analysis of cable structures subjected to wave forces and ground motions in the ocean. A geometrically nonlinear finite element procedure using the isoparamnetrie curved cable element based on the Lagrangian folmulation is briefly summarized. A simple and accurate method to determine the initial equilibrium state of cable systems associated with self-weights, buoyancy and the motion of end points is presented using the load incremental method combined with penalty method. Also the Newmark method is used for dynamic nonlinear analysis of ocean cables. Numerical examples are presented to validate the present numerical method.     

Numerical and Experimental Investigation of Hydrodynamic Interactions of Two VLFS Modules Deployed in Tandem

This paper numerically and experimentally investigates the hydrodynamic interaction between two semi-submersible type VLFS modules in the frequency domain. Model tests were conducted to investigate the relationship between interactions and wave headings. Numerical studies were performed by solving the radiation-diffraction problem and were validated against the experimental results. Motion Response Amplitude Operators (RAOs) were obtained from numerical and experimental studies. The dependency of the hydrodynamic interaction effect on wave headings is clarified. The influence of different wave periods on the motion responses of two-module VLFS and wave elevations in the gap is studied. The results indicate that the hydrodynamic interactions of the two modules are directly related to the wave headings and the periods of the incident wave. The shielding effect plays an important role in short wave, and the influence decreases with the increase of the incident wavelength. The numerical results based on the diffraction-radiation code can give a relatively good estimation to the responses in short wave while for long wave, it would over-predict the response.     

Hydroelastic analysis of pontoon-type circular VLFS with an attached submerged plate

This paper is concerned with the hydroelastic analysis of a pontoon-type, circular, very large floating structure (VLFS) with a horizontal submerged annular plate attached around its perimeter. The coupled fluid–structure interaction problem may be solved by using the modal expansion method in the frequency domain. It involves, firstly, the decomposition of the deflection of a circular Mindlin plate with free edges into vibration modes that are obtained analytically. Then the hydrodynamic diffraction and radiation forces are evaluated by using the eigenfunction expansion matching method which can also be done in an exact manner. The hydroelastic equation of motion is solved by the Rayleigh–Ritz method for the modal amplitudes, and then the modal responses are summed up to obtain the total response. The effectiveness of the attached submerged annular plate in reducing the motion of VLFS has been confirmed by the analysis.     

Extracting energy while reducing hydroelastic responses of VLFS using a modular raft wec-type attachment

This paper presents the use of a modular raft Wave Energy Converter (WEC)-type attachment at the fore edge of a rectangular Very Large Floating Structure (VLFS) for extracting wave energy while reducing hydroelastic responses of the VLFS under wave action. The proposed modular attachment comprises multiple independent auxiliary pontoons (i.e. modules) that are connected to the fore edge of the VLFS with hinges and linear Power Take-Off (PTO) systems. For the hydroelastic analysis, the auxiliary pontoons and the VLFS are modelled by using the Mindlin plate theory while the linear wave theory is used for modelling the fluid motion. The analysis is performed in the frequency domain using the hybrid Finite Element-Boundary Element (FE-BE) method. Parametric studies are carried out to investigate the effects of pontoon length, PTO damping coefficient, gap between auxiliary pontoons, and incident wave angle on the power capture factor as well as reductions in the hydroelastic responses of the VLFS with the modular attachment. It is found that in oblique waves, the modular attachment comprising multiple narrow pontoons outperforms the corresponding rigid attachment that consists of a single wide pontoon with respect to the power capture factor and the reduction in the deflection of the VLFS. In addition, it is possible to have a considerable gap between pontoons without significantly compromising the effectiveness of the modular attachment.     

Oblique Wave-Induced Responses of A VLFS Edged with A Pair of Inclined Perforated Plates

This paper is concerned with the hydroelastic responses of a mat-like, rectangular very large floating structure (VLFS) edged with a pair of horizontal/inclined perforated anti-motion plates in the context of the direct coupling method. The updated Lagrangian formulae are applied to establish the equilibrium equations of the VLFS and the total potential formula is employed for fluids in the numerical model including the viscous effect of the perforated plates through the Darcy''s law. The hybrid finite element-boundary element (FE-BE) method is implemented to determine the response reduction of VLFS with attached perforated plates under various oblique incident waves. Also, the numerical solutions are validated against a series of experimental tests. The effectiveness of the attached perforated plates in reducing the deflections of the VLFS can be significantly improved by selecting the proper design parameters such as the porous parameter, submergence depth, plate width and inclination angle for the given sea conditions.     

Hull/mooring/riser coupled dynamic analysis and sensitivity study of a tanker-based FPSO

A computer program is developed for hull/mooring/riser coupled dynamic analysis of a tanker-based turret-moored FPSO (Floating Production Storage and Offloading) in waves, winds, and currents. In this computer program, the floating body is modeled as a rigid body with six degrees of freedom. The first- and second-order wave forces, added mass, and radiation damping at various yaw angles are calculated from the second-order diffraction/radiation panel program WAMIT. The wind and current forces for various yaw angles of FPSO are modeled following the empirical method suggested by OCIMF (Oil Company International Marine Forum).

The mooring/riser dynamics are modeled using a rod theory and finite element method (FEM), with the governing equations described in a generalized coordinate system. The dynamics of hull, mooring lines, and risers are solved simultaneously at each time step in a combined matrix for the specified connection condition. For illustration, semi-taut chain-steel wire-chain mooring lines and steel catenary risers are employed and their effects on global FPSO hull motions are investigated. To better understand the physics related to the motion characteristics of a turret-moored FPSO, the role of various hydrodynamic contributions is analyzed and assessed including the effects of hull and mooring/riser viscous damping, second-order difference-frequency wave-force quadratic transfer functions, and yaw-angle dependent wave forces and hydrodynamic coefficients. To see the effects of hull and mooring/riser coupling and mooring/riser damping more clearly, the case with no drag forces on those slender members is also investigated. The numerical results are compared with MARIN's wave basin experiments.     

Structural Analysis of Platforms with the Effect of Joint Flexibility

- A modified space beam element is presented in this paper to consider the local joint flexibility of T, Y tubular joints subjected to axial forces and in- plane bending moments for analysis of platforms. Two numerical examples are shown to verify the efficiency and validity of the method presented here.     

Performance characteristics of a conceptual ring-shaped spar-type VLFS with double-layered perforated-wall breakwater

A ring-shaped spar-type Very Large Floating Structure (VLFS) is proposed as an intermediate base for supporting deepwater resource exploitation far away from the coast line. The proposed VLFS is composed of eight rigidly connected deep-draft spar-type modules and an inside harbor. A double-layered perforated-wall breakwater is vertically attached to the VLFS and pierces through the water surface to attenuate the wave energy in the inside harbor. The hydrodynamic performance characteristics of the ring-shaped VLFS was experimentally evaluated in the present study, focusing on the motion responses, wave elevations, and wave run-ups. The natural periods of the motions in vertical plane were determined to be larger than 40 s, which is much larger than common wave periods. This enhanced the motion performance in vertical plane and afforded favorable habitation and operation condition on the VLFS. A large surge damping was induced by the vertical breakwater, which tended to significantly affect the surge and pitch motions, but had a negligible effect on the heave motion. The component frequencies of the wave elevations in the inside harbor and the wave run-ups were identical with those of the incident waves. The wave attenuation was frequency-dependent and effective for the common wave frequencies, with a smaller loss coefficient observed in higher sea state. The wave attenuation and wave run-ups tended to improve in the absence of the leeward walls.     

多模块超大型浮体中连接器刚度对其运动响应的影响

多模块超大型浮体一般由连接器连接,实现海上浮动机场等功能。实际操作中,为约束超大型浮体模块之间的相对运动,连接器通常将承受非常巨大的载荷,给连接器的制造带来巨大的困难。通过对不同环境力情况下不同刚度连接器的研究,分析了连接器刚度对超大型浮体模块之间相对运动与连接器自身承受载荷的影响。研究发现,随着柔性连接器刚度的增加,连接器对超大浮体模块之间相对运动的约束逐渐增强,同时连接器也将承受更大的载荷;此外,较大的连接器刚度,并不利于抵抗模块之间的冲击载荷;最后,连接器刚度的改变会影响其固有振动频率,因此需要尽可能避开共振区域,否则系统容易出现较大的振动,导致模块间相对运动过大,连接器过载。研究结果确定了连接器刚度最佳匹配原则,以指导连接器的工程设计。     

Effect of slowly varying drift forces on the motion characteristics of truss spar platforms

Spar platform has been regarded as a competitive floating structure for deep and ultra deep water oil and gas production. In this paper, an efficient methodology has been developed to determine the slow motion responses of slender floating offshore structures due to wave forces. Based on this methodology, a MATLAB program named ‘TRSPAR’ was developed to predict the dynamic responses in time domain and it was used in this study to obtain the numerical results of a typical truss spar platform connected to sea bed using nine taut mooring lines. The difference frequency forces were calculated using the principles of the extension of Morison equation for an inclined cylinder and the wave kinematics were predicted using hyperbolic extrapolation. Mooring lines were modelled as nonlinear springs and their stiffness was obtained by conducting the static offset simulation. Because of the lack of detailed calculations in literature, most of the equations used were derived and presented in this paper. The effects of the different sources of the second order difference frequency forces were compared for inertia and drag forces in terms of response spectra. To validate the TRSPAR code, its results were compared to results of a typical truss spar model test.     

Mooring forces and motion responses of pontoon-type floating breakwaters

The experimental and theoretical investigations on the behaviour of pontoon-type floating breakwaters are presented. A two-dimensional finite element model is adopted to study the behaviour of pontoon-type floating breakwaters in beam waves. The stiffness coefficients of the slack mooring lines are idealized as the linear stiffness coefficients, which can be derived from the basic catenary equations of the cable. The theoretical model is supported by an experimental programme conducted in a wave flume. The motion responses and mooring forces are measured for three different mooring configurations, and the results are reported and discussed in detail in this paper. The wave attenuation characteristics are presented for the configurations studied.     

Non-linear restoring forces of an offshore platform

The method of calculation of non-linear restoring forces presented in this paper is simple, concise and feasible to apply easily in the calculation of restoring forces of platforms in order to simulate motion responses of offshore platforms in the time-domain. In this method, hydrostatic restoring forces and moments are related to the translational and/or rotational displacements. Calculations of non-linear yaw, roll and pitch restoring moments are based on the catenary type of moorings. Although the method presented here is a simple one, it is capable of the calculation of restoring forces for use in the time-domain motion simulations of offshore platforms, with an acceptable degree of accuracy when the numerical simulation results were compared with the experimental measurements.     

Study on coupling effects of ship motion and sloshing

This study considers the coupling effects of ship motion and sloshing. The linear ship motion is solved using an impulse-response-function (IRF) method, while the nonlinear sloshing flow is simulated using a finite-difference method. The IRF method requires the frequency-domain solution prior to conversion to time domain, but the computational effort is much less than that of direct time-domain approaches. The developed scheme is verified by comparing the motion RAOs between the frequency-domain solution and the solution obtained by the IRF method. Furthermore, a soft-spring concept and linear roll damping are implemented to predict more realistic motions of surge, sway, yaw, and roll. For the simulation of sloshing flow in liquid tanks, a physics-based numerical approach adopted by Kim [2001. Numerical simulation of sloshing flows with impact load. Applied Ocean Research 23, 53–62] and Kim et al. [2004. Numerical study on slosh-induced impact pressures on three-dimensional prismatic tanks. Applied Ocean Research 26, 213–226] is applied. In particular, the present method focuses on the simulation of the global motion of sloshing flow, ignoring some local phenomena. The sloshing-induced forces and moments are added to wave-excitation forces and moments, and then the corresponding body motion is obtained. The developed schemes are applied for two problems: the sway motion of a box-type barge with rectangular tanks and the roll motion of a modified S175 hull with rectangular anti-rolling tank. Motion RAOs are compared with existing results, showing fair agreement. It is found that the nonlinearity of sloshing flow is very important in coupling analysis. Due to the nonlinearity of sloshing flow, ship motion shows a strong sensitivity to wave slope.     

A parametric study of wave loads on trimaran ships traveling in waves

In this paper, we present a spectral analysis based on wave loads to select suitable side-hull arrangements for a trimaran ship traveling in waves. Neglecting the steady flow effect, the three-dimensional source-distribution method, using a pulsating source potential incorporating the panel method, is adopted to solve the corresponding hydrodynamic coefficients. The significant values for wave loads, including shear forces, bending moments, and torsion moments at different locations on the main hull and connected deck with respect to different staggers and clearances, are derived by the spectral analysis. Several ship speeds and wave headings are also considered for comparison. This study offers more information for selecting the side-hull arrangement from the viewpoint of wave loads on trimaran ships, which may be regarded as helpful references for seakeeping design of these types of ships.     

Comparison of Linear Level I Green-Naghdi Theory with Linear Wave Theory for Prediction of Hydroelastic Responses of VLFS

Very Large Floating Structures (VLFS) have drawn considerable attention recently due to their potential significance in the exploitation of ocean resources and in the utilization of ocean space. Efficient and accurate estimation of their hydroelastic responses to waves is very important for the design. Recently, an efficient numerical algorithm was developed by Ertekin and Kim (1999). However, in their analysis, the linear Level I Green-Naghdi (GN) theory is employed to describe fluid dynamics instead of the conventional linear wave (LW) theory of finite water depth. They claimed that this linear level I GN theory provided betler predictions of the hydroelastic responses of VLFS than the linear wave theory. In this paper, a detailed derivation is given in the conventional linear wave theory framework with the same quantity as used in the linear level I GN theory framework. This allows a critical comparison between the linear wave theory and the linear level I GN theory. it is found that the linear level     

Hydroelastic Response Analysis of Mat-Like VLFS over A Plane Slope in Head Seas

1 .IntroductionIntheexploitationofoceanresourcesandintheutilizationofoceanspaces,verylargefloatingstructures (VLFS)suchasMega FloatinJapan (Isobe ,1 999)andMobileOffshoreBase (MOB)inUSA (Remmers ,1 999)playasignificantrole .However,owingtotheirlargesizesandrelativelylowbendingrigidities ,theirhydroelasticresponsesinwavesareofthemostconcern .ManystudieshavebeencarriedoutforthepredictionofthehydroelasticresponsesofVLFS′s (Kashiwagi,2 0 0 0 ;Cui,2 0 0 2 ) .However,inalmostallofthesestu…     

Time Domain Simulation of Transient Responses of Very Large Floating Structures Under Unsteady External Loads

A time domain finite element method （FEM） for the analysis of transient elastic response of a very large floating structure （VLFS） subjected to arbitrary time-dependent external loads is presented. This method is developed directly in time domain and the hydrodynamic problem is formulated based on linear, inviscid and slightly compressible fluid theory and the structural response is analyzed on the thin plate assumption. The time domain finite element procedure herein is validated by comparing numerical results with available experimental data. Finally, the transient elastic response of a pontoon-type VLFS under the landing of an airplane is computed by the proposed time domain FEM. The time histories of the applied force and the position and velocity of an airplane during landing are modeled with data from a Boeing 747-400 jumbo jet.     

Motion and Dynamic Responses of A Semisubmersible in Freak Waves

The present research aims at clarifying the effects of freak wave on the motion and dynamic responses of a semisubmersible. To reveal the effects of mooring stiffness, two mooring systems were employed in the model tests and time-domain simulations. The 6-DOF motion responses and mooring tensions have been measured and the 3-DOF motions of fairleads were calculated as well. From the time series, trajectories and statistics information, the interactions between the freak wave and the semisubmersible have been demonstrated and the effects of mooring stiffness have been identified. The shortage of numerical simulations based on 3D potential flow theory is presented. Results show that the freak wave is likely to cause large horizontal motions for soft mooring system and to result in extremely large mooring tensions for tight mooring system. Therefore, the freak wave is a real threat for the marine structure, which needs to be carefully considered at design stage.     

波浪作用下中上层浮鱼礁动力响应数值模型建立方法

人工浮鱼礁型式多样,适应水深范围广,优化锚泊方式可规模化建设浮鱼礁群,是海洋中上层生境构建的重要手段。中上层浮鱼礁投放于近海,属于海岸工程范畴,抗浪性能是其结构设计的关键。根据有限单元法和集中质量点法,详细阐述和推导了中上层浮鱼礁各构成组件连接位置处点或单元的相互耦合受力和运动处理方法,以及浮鱼礁出水条件的判别方法和水质点速度、加速度的修正方法。建立的波浪作用下三维浮鱼礁动力响应数值模型与其在波浪水槽中的物理模型试验对比,验证了数值模型的正确性。最后建立了一种新型锚泊方式的浮鱼礁动力响应数值模型,分析了浮鱼礁摆动角度、锚绳拉力、网衣系缚点总拉力的历时变化。研究结果可为中上层浮鱼礁优化结构形状和搭配浮体、配重提供判断依据。