掺硼金刚石薄膜的电化学性能

利用循环伏安法,通过对比掺硼金刚石薄膜电极和铂／金刚石电极分别作为工作电极时的循环伏安曲线,分析了两种电极表现出的电化学性能差别,并利用能级理论进行了机理探讨。结果表明掺硼金刚石薄膜电极具有宽的电化学窗口（宽度约为3V）、良好的化学稳定性和极低的背景电流（接近0）,是一种较有潜力的电化学电极材料。     

Direct electrochemical oxidation of disulfides at anodically pretreated boron-doped diamond electrodes

Anodically oxidized diamond electrodes have been used to oxidize disulfides, thiols, and methionine in aqueous acidic media and tested for amperometric detection of these compounds after chromatographic separation. Cyclic voltammetric signals for 1 mM glutathione disulfide (GSSG) were observed at 1.39 and 1.84 V vs SCE, the values being less positive than those of its as-deposited counterpart as well as glassy carbon electrode. The voltammetric and chronocoulometric results have indicated the high stability of the electrode with negligible adsorption. A positive shift in the peak potential with increasing pH indicated the attractive electrostatic interaction between the anodically oxidized diamond surface and the positively charged GSSG in acidic media that promoted its analytical performance. The results of the electrolysis experiments of disulfides and thiols showed that the oxidation reaction mechanism of glutathione (GSH) and GSSG involves oxygen transfer. Following separation by liquid chromatography (LC), the determination of both GSH and GSSG in rat whole blood was achieved at a constant potential (1.50 V vs Ag/AgCl), and the limits of detection for GSH and GSSG were found to be 1.4 nM (0.028 pmol) and 1.9 nM (0.037 pmol) with a linear calibration range up to 0.25 mM. These detection limits were much lower than those reported for the amperometry using Bi-PbO2 electrodes and LC-mass spectrometry, and the LC method using diamond electrodes were comparable with enzymatic assay in real sample analysis. The high response stability and reproducibility together with the possibility of regeneration of the electrode surface by on-line anodic treatment at 3 V for 30 min further support the applicability of anodically pretreated diamond for amperometric detection of disulfides.     

Active sites for outer-sphere, inner-sphere, and complex multistage electrochemical reactions at polycrystalline boron-doped diamond electrodes (pBDD) revealed with scanning electrochemical cell microscopy (SECCM)

The local rate of heterogeneous electron transfer (HET) at polycrystalline boron-doped diamond (pBDD) electrodes has been visualized at high spatial resolution for various aqueous electrochemical reactions, using scanning electrochemical cell microscopy (SECCM), which is a technique that uses a mobile pipet-based electrochemical cell as an imaging probe. As exemplar systems, three important classes of electrode reactions have been investigated: outer-sphere (one-electron oxidation of ferrocenylmethyltrimethylammonium (FcTMA(+))), inner-sphere (one-electron oxidation of Fe(2+)), and complex processes with coupled electron transfer and chemical reactions (oxidation of serotonin). In all cases, the pattern of reactivity is similar: the entire pBDD surface is electroactive, but there are variations in activity between different crystal facets which correlate directly with differences in the local dopant level, as visualized qualitatively by field-emission scanning electron microscopy (FE-SEM). No evidence was found for enhanced activity at grain boundaries for any of the reactions. The case of serotonin oxidation is particularly interesting, as this process is known to lead to deterioration of the electrodes, because of blocking by reaction products, and therefore cannot be studied with conventional scanning electrochemical probe microscopy (SEPM) techniques. Yet, we have found this system nonproblematic to study, because the meniscus of the scanning pipet is only in contact with the surface investigated for a brief time and any blocking product is left behind as the pipet moves to a new location. Thus, SECCM opens up the possibility of investigating and visualizing much more complex heterogeneous electrode reactions than possible presently with other SEPM techniques.     

Thiol-yne reaction on boron-doped diamond electrodes: application for the electrochemical detection of DNA-DNA hybridization events

Boron-doped diamond (BDD) interfaces were chemically functionalized through the catalyst free thiol-yne reaction. Different thiolated precursors (e.g., perfluorodecanethiol, 6-(ferrocenyl)-hexanethiol, DNA) were successfully "clicked" to alkynyl-terminated BDD by irradiating the interface at 365 nm for 30 min. Thiolated oligonucleotide strands were immobilized using the optimized reaction conditions, and the surface concentration was tuned to obtain a surface coverage of 3.1 × 10(12) molecules cm(-2). Electrochemical impedance spectroscopy (EIS) was employed to follow the kinetics of hybridization and dehybridization events. The sensitivity of the oligonucleotide modified BDD interface was assayed, and a detection limit of 1 nM was obtained.     

壳聚糖修饰掺硼金刚石薄膜电极测定铜离子

通过热丝化学气相沉积(HFCVD)的方法,以钽(Ta)为衬底,三氧化二硼(Be2O3)为硼源,制备掺硼金刚石(BDD)薄膜.并采用共价键合法进一步制得壳聚糖修饰BDD薄膜电极.以此修饰电极为工作电极,在0.1mol/L,pH=4的磷酸氢二钠缓冲液中对Cu2+进行检测.实验表明,Cu2+在4.0×10-7～1.0×10-...     

Electrochemical degradation of chlorobenzene on boron-doped diamond and platinum electrodes

In this paper the electrochemical degradation of chlorobenzene (CB) was investigated on boron-doped diamond (BDD) and platinum (Pt) anodes, and the degradation kinetics on these two electrodes was compared. Compared with the total mineralization with a total organic carbon (TOC) removal of 85.2% in 6 h on Pt electrode, the TOC removal reached 94.3% on BDD electrode under the same operate condition. Accordingly, the mineralization current efficiency (MCE) during the mineralization on BDD electrode was higher than that on the Pt electrode. Besides TOC, the conversion of CB, the productions and decay of intermediates were also monitored. Kinetic study indicated that the decay of CB on BDD and Pt electrodes were both pseudo-first-order reactions, and the reaction rate constant (k_s) on BDD electrode was higher than that on Pt electrode. The different reaction mechanisms on the two electrodes were investigated by the variation of intermediates concentrations. Two different reaction pathways for the degradation of CB on BDD electrode and Pt electrode involving all these intermediates were proposed.     

Electrochemical oxidation of oxalic acid at highly boron-doped diamond electrodes

Electrochemical oxidation of oxalic acid has been investigated at bare, highly boron-doped diamond electrodes. Cyclic voltammetry and flow injection analysis with amperometric detection were used to study the electrochemical reaction. Hydrogen-terminated diamonds exhibited well-defined peaks of oxalic acid oxidation in a wide pH range. A good linear response was observed for a concentration range from 50 nM to 10 microM, with an estimated detection limit of approximately 0.5 nM (S/N = 3). In contrast, oxygen-terminated diamonds showed no response for oxalic acid oxidation inside the potential window, indicating that surface termination contributed highly to the control of the oxidation reaction. An investigation with glassy carbon electrodes was conducted to confirm the surface termination effect on oxalic acid oxidation. Although a hydrogen-terminated glassy carbon electrode showed an enhancement of signal-to-background ratio in comparison with untreated glassy carbon, less stability of the current responses was observed than that at hydrogen-terminated diamond.     

Surface nanostructuring of boron-doped diamond films and their electrochemical performance

Uniform and vertically aligned nanocone and nanopillar arrays were successfully constructed on heavily boron-doped nanocrysatlline diamond films by carrying out bias-assisted reactive ion etching in hydrogen/argon plasmas. The electrochemical properties of the nanostructured boron-doped diamond films were investigated by cyclic voltammetry using 1 mM [Fe(CN)6](3-/4-) as redox couple. Compared to the planar boron-doped nanocrystalline diamond film electrode, the surface nanostructuring of boron-doped diamond film electrodes demonstrate enhanced sensitivity due to their enlarged electro-active surface areas. The results indicated that boron-doped diamond nanocones and nanopillars are promising electrode materials which benefit to improve the efficiency, sensitivity and reproducibility of biomedical and chemical sensors.     

Examination of the spatially heterogeneous electroactivity of boron-doped diamond microarray electrodes

Spatial variations in the electrical and electrochemical activity of microarray electrodes, fabricated entirely from diamond, have been investigated. The arrays contain approximately 50-mum-diameter boron-doped diamond (BDD) disks spaced 250 mum apart (center to center) in insulating intrinsic diamond supports, such that the BDD regions are coplanar with the intrinsic diamond. Atomic force microscopy (AFM) imaging of the surface reveals a roughness of no more than +/-10 nm over the array. Each BDD microdisk within the array contains polycrystalline BDD with a variety of different grains exposed. Using conducting-AFM, the conductivity of the different grains was found to vary within a BDD microdisk. Electrochemical imaging of the electroactivity of the microdisk electrodes using scanning electrochemical microscopy operating in substrate generation-tip collection mode revealed that, under apparently diffusion-limited steady-state conditions, there was a small variation in the response between electrodes. However, the majority of electrodes in the array appeared to show predominantly metallic behavior. For the electrodes that showed a lower activity, all grains within the microdisk supported electron transfer, albeit at different rates, as evidenced by studies on the electrodeposition of metallic silver, at potentials far negative of the flat band potential of oxygen-terminated polycrystalline diamond. The possibility of using these array electrodes for steady-state diffusion-limited measurements in electroanalytical applications is far-reaching. However, caution should be exercised in the kinetic analysis of voltammetric measurements, since wide variations in the electroactivity of individual grains are apparent when the potential is below the diffusion-limited value.     

Diamond-modified AFM probes: from diamond nanowires to atomic force microscopy-integrated boron-doped diamond electrodes

In atomic force microscopy (AFM), sharp and wear-resistant tips are a critical issue. Regarding scanning electrochemical microscopy (SECM), electrodes are required to be mechanically and chemically stable. Diamond is the perfect candidate for both AFM probes as well as for electrode materials if doped, due to diamond's unrivaled mechanical, chemical, and electrochemical properties. In this study, standard AFM tips were overgrown with typically 300 nm thick nanocrystalline diamond (NCD) layers and modified to obtain ultra sharp diamond nanowire-based AFM probes and probes that were used for combined AFM-SECM measurements based on integrated boron-doped conductive diamond electrodes. Analysis of the resonance properties of the diamond overgrown AFM cantilevers showed increasing resonance frequencies with increasing diamond coating thicknesses (i.e., from 160 to 260 kHz). The measured data were compared to performed simulations and show excellent correlation. A strong enhancement of the quality factor upon overgrowth was also observed (120 to 710). AFM tips with integrated diamond nanowires are shown to have apex radii as small as 5 nm and where fabricated by selectively etching diamond in a plasma etching process using self-organized metal nanomasks. These scanning tips showed superior imaging performance as compared to standard Si-tips or commercially available diamond-coated tips. The high imaging resolution and low tip wear are demonstrated using tapping and contact mode AFM measurements by imaging ultra hard substrates and DNA. Furthermore, AFM probes were coated with conductive boron-doped and insulating diamond layers to achieve bifunctional AFM-SECM probes. For this, focused ion beam (FIB) technology was used to expose the boron-doped diamond as a recessed electrode near the apex of the scanning tip. Such a modified probe was used to perform proof-of-concept AFM-SECM measurements. The results show that high-quality diamond probes can be fabricated, which are suitable for probing, manipulating, sculpting, and sensing at single digit nanoscale.     

Electrochemical oxidation of histamine and serotonin at highly boron-doped diamond electrodes

The electrochemistry of histamine and serotonin in neutral aqueous media (pH 7.2) was investigated using polycrystalline, boron-doped diamond thin-film electrodes. Cyclic voltammetry, hydrodynamic voltammetry, and flow injection analysis (FIA) with amperometric detection were used to study the oxidation reactions. Comparison experiments were carried out using polished glassy carbon (GC) electrodes. At diamond electrodes, highly reproducible and well-defined cyclic voltammograms were obtained for histamine with a peak potential at 1.40 V vs SCE. The voltammetric signal-to-background ratios obtained at diamond were 1 order of magnitude higher than those obtained for GC electrodes at and above 100 microM analyte concentrations. A linear dynamic range of 3-4 orders of magnitude and a detection limit of 1 microM were observed in the voltammetric measurements. Well-defined sweep rate-dependent voltammograms were also obtained for 5-hydroxytryptamine (5-HT). The characteristics of the voltammogram indicated lack of adsorption of its oxidation products on the surface. No fouling or deactivation of the electrode was observed within the experimental time of several hours. A detection limit of 0.5 microM (signal-to-noise ratio 13.8) for histamine was obtained by use of the FIA technique with a diamond electrode. A remarkably low detection limit (10 nM) was obtained for 5-HT on diamond by the same method. Diamond electrodes exhibited a linear dynamic range from 10 nM to 100 microM for 5-HT determination and a range of 0.5-100 microM for histamine determination. The FIA response was very reproducible from film to film, and the response variability was below 7% at the actual detection limits.     

Electrochemical performance of diamond thin-film electrodes from different commercial sources

The electrochemical properties of two commercial (Condias, Sumitomo) boron-doped diamond thin-film electrodes were compared with those of two types of boron-doped diamond thin film deposited in our laboratory (microcrystalline, nanocrystalline). Scanning electron microscopy and Raman spectroscopy were used to characterize the electrode morphology and microstructure, respectively. Cyclic voltammetry was used to study the electrochemical response, with five different redox systems serving as probes (Fe(CN)(6)(3)(-)(/4)(-), Ru(NH(3))(6)(3+/)(2+), IrCl(6)(2)(-)(/3)(-), 4-methylcatechol, Fe(3+/2+)). The response for the different systems was quite reproducibile from electrode type to type and from film to film for electrodes of the same type. For all five redox systems, the forward reaction peak current varied linearly with the scan rate(1/2) (nu), indicative of electrode reaction kinetics controlled by mass transport (semi-infinite linear diffusion) of the reactant. Apparent heterogeneous electron-transfer rate constants, k degrees (app), for all five redox systems were determined from deltaE(p)-nu experimental data, according to the method described by Nicholson (Nicholson, R. S. Anal. Chem. 1965, 37, 1351.). The rate constants were also verified through digital simulation (DigiSim 3.03) of the voltammetric i-E curves at different scan rates. Good fits between the experimental and simulated voltammograms were found for scan rates up to 50 V/s. k degrees (app) values of 0.05-0.5 cm/s were observed for Fe(CN)(6)(3)(-)(/4)(-), Ru(NH(3))(6)(3+/2+), and IrCl(6)(2)(-)(/3)(-) without any extensive electrode pretreatment (e.g., polishing). Lower k degrees (app) values of 10(-)(4)-10(-)(6) cm/s were found for 4-methylcatechol and Fe(3+/2+). The voltammetric responses for Fe(CN)(6)(3)(-)(/4)(-) and Ru(NH(3))(6)(3+/2+) were also examined at all four electrode types at two different solution pH (1.90, 7.35). Since the hydrogen-terminated diamond surfaces contain few, if any, ionizable carbon-oxygen functionalities (e.g., carboxylic acid, pK(a) approximately 4.5), the deltaE(p), i(p)(ox), and i(p)(red) values for the two systems were, for the most part, unaffected by the solution pH. This is in contrast to the typical behavior of oxygenated, sp(2) carbon electrodes, such as glassy carbon.     

Junction like behavior in polycrystalline diamond films

We have successfully fabricated polycrystalline diamond rectifying junction devices on n-type (1 0 0) silicon substrates by Hot Filament Chemical Vapor Deposition (HFCVD) using methane/hydrogen process gas and trimethyl borate and trimethyl phosphite dissolved in acetone as p- and n-type dopants, respectively. Impedance spectroscopy and current-voltage analysis indicates that the conduction is vertical down the grains and facets and not due to surface effects. Electrical characteristics were analyzed with In and Ti/Au top metal contacts with Al as the substrate contact. Current-voltage characteristics as a function of temperature showed barrier potentials of 1.1 eV and 0.77 eV for the In and Ti/Au contacts, respectively. Barrier heights of 4.8 eV (In) and 4.4 eV (Ti/Au) were obtained from capacitance-voltage measurements.     

Electrochemical detection of arsenic(III) using iridium-implanted boron-doped diamond electrodes

Iridium-modified, boron-doped diamond electrodes fabricated by an ion implantation method have been developed for electrochemical detection of arsenite (As(III)). Ir+ ions were implanted with an energy of 800 keV and a dose of 10(15) ion cm(-2). An annealing treatment at 850 degrees C for 45 min in H2 plasma (80 Torr) was required to rearrange metastable diamond produced by an implantation process. Characterization was investigated by SEM, AFM, Raman, and X-ray photoelectron spectroscopy. Cyclic voltammetry and flow injection analysis with amperometric detection were used to study the electrochemical reaction. The electrodes exhibited high catalytic activity toward As(III) oxidation with the detection limit (S/N = 3), sensitivity, and linearity of 20 nM (1.5 ppb), 93 nA microM(-1) cm(-2), and 0.999, respectively. The precision for 10 replicate determinations of 50 microM As(III) was 4.56% relative standard deviation. The advantageous properties of the electrodes were its inherent stability with a very low background current. The electrode was applicable for analysis of spiked arsenic in tap water containing a significant amount of various ion elements. The results indicate that the metal-implanted method could be promising for controlling the electrochemical properties of diamond electrodes.     

Electrochemical treatment of soil-washing effluent with boron-doped diamond electrodes: A review

In recent years, electrochemical technologies have been widely used to remove contaminants at lab-scale and semi-pilot scale. Boron-doped diamond (BDD) electrodes have been considered as efficient materials for the abatement of persistent organic pollutants owing to their outstanding properties, such as rapid rates of electron-transfer for soluble redox systems, wide electrochemical potential window for water discharge reactions in aqueous and non-aqueous electrolytes, and high stability. Similar to other applications of electrochemical technology, wastes display medium to high ionic conductivity. Therefore, one of the applications highlighted for the electrolysis with these new electrodes is the treatment of soil-washing fluids, because in the polluted streams, washing of polluted soils provides a suitable conductivity to the effluent. In this context, this review summarizes the application of conductive diamond anodes for the electrochemical treatment of soil-washing effluents contaminated with different persistent organic pollutant such as pesticides, hydrocarbons, dyes, and organochlorine compounds, in single anodic oxidation processes and in other more complex processes such as electro-Fenton, photoelectrolysis, or sonoelectrolysis. Finally, the challenges and future research directions of electrochemical technology are discussed and outlined at pilot and prototype scale.     

Effect of oxygen terminated surface of boron-doped diamond thin-film electrode on seawater salinity sensing

Tremendous demands for highly sensitive and stable seawater salinometers have motivated intensive research on advanced electrode materials.Boron-doped diamond(BDD)is attractive in terms of its high mechanical stability and chemical inertness,but is usually hindered by its low double-layer capacitance(Cdl)for seawater salinity detection.Here,inspired by the principle of oxygen-terminated BDD electrode endowing higher Cdl than hydrogen-terminated surface,we introduce the oxygen terminated surface by oxygen plasma or reactive ion etch(RIE),and the fabricated oxygen terminated BDD electrodes demon-strate high sensitivity and long-term stability in seawater salinity detection comparing with the hydrogen terminated BDD electrodes.Significantly,the as-fabricated O-BDD-RIE electrodes not only show remark-able enhanced response even better than the commercial platinum black electrodes but also display long-time stability which is weekly verified by continuous monitor for 90 days.The outstanding per-formance of the oxygen terminated BDD electrodes can be ascribed to the enhancement of C-0 surface functional group on Cdl.In addition,a comprehensive analysis of effective electroactive surface area(EASA)and Cdl proves that the surface oxygen is the major factor for the improved Cdl.In summary,the excellent oxygen terminated BDD electrodes promise potential application in seawater salinity detection.     

Microchip capillary electrophoresis coupled with a boron-doped diamond electrode-based electrochemical detector

The attractive behavior and advantages of a diamond electrode detector for a micromachined capillary electrophoresis (CE) system are discussed. A chemically vapor-deposited boron-doped diamond (BDD) film band (0.3 x 6.0 mm) electrode is used for end-column amperomettic detection. The favorable performance of the diamond electrode microchip detector is indicated from comparison to a commonly used thick-film carbon detector. The diamond electrode offers enhanced sensitivity, lower noise levels, and sharper peaks for several groups of important anaytes (nitroaromatic explosives, organophosphate nerve agents, phenols). The favorable signal-to-background characteristics of the BDD-based CE detector are coupled with a greatly improved resistance to surface fouling and greater isolation from high separation voltages. The enhanced stability is indicated from a RSD of 0.8% for 60 repetitive measurements of 5 ppm 2,4,6-trinitrotoluene (vs RSD of 10.8% at the thick-film carbon electrode). A highly linear response is obtained for the explosives 1,3-dinitrobenzene and 2,4-dinitrotoluene over the 200-1,400 ppb range, with detection limits of 70 and 110 ppb, respectively. Factors influencing the performance of the BDD detector are assessed and optimized. The attractive properties of BDD make it very promising material for electrochemical detection in CE microchip systems and other micromachined flow analyzers.     

Fabrication of boron-doped diamond ultramicroelectrodes for use in scanning electrochemical microscopy experiments

Boron-doped diamond (BDD) ultramicroelectrode (UME) tips were fabricated by the growth of BDD films by chemical vapor deposition onto sharpened tungsten wires. Both nanocrystalline and microcrystalline forms of diamond coatings were examined. The diamond-coated wires were selectively insulated with nail varnish, electrophoretic paint, or fast-setting epoxy to form UME tips of critical dimensions of 1-25 microm. The geometry of the exposed electrode area was disk or hemispherical in most cases. Cyclic voltammetry and chronoamperometry were used to assess exposed electrode area and integrity of the insulation. BDD UMEs were used to obtain SECM approach curves to an insulating and a conducting substrate, which were fitted to the theory appropriate for the observed tip geometry. The tips were used to obtain SECM images of immobilized respiring E. coli, illustrating the suitability of BDD UMEs for electrochemical imaging in biological media.     

自支撑硼掺杂金刚石膜残余应力和微观应力的XRD分析

利用XRD(包括sin2ψ法)研究了电子辅助热灯丝化学气相沉积法(EA-HFCVD)生长的自支撑硼掺杂多晶金刚石薄膜的残余应力和微观应力.结果表明,薄膜的残余应力为压应力,随着薄膜制备过程中硼流量的增加,应力值有减小的趋势.薄膜的微观应力随着硼流量的增加,由拉应力转变为压应力然后又转变为拉应力.残余应力和微观应力的变化归因于一定量的硼掺杂导致的多晶膜中晶粒尺寸、晶面取向及孪晶变化的共同作用.     

掺硼金刚石膜电极在液晶盒残留液晶清洗中的应用研究

目前液晶盒残留液晶的清洗一般采用非ODS有机溶剂的溶解或表面活性剂的乳化分散作用来去除，效果并不十分理想。应用掺硼金刚石膜电极这一现今热点研究的功能材料，提出了将金刚石膜电极电化学高级氧化技术的氧化分解作用与水基清洗剂的传质、渗透、分散作用相结合的清洗技术，并通过实验确定了K3PO4添加浓度为0．4mol，L和清洗温度为70℃的最佳关键清洗参数，能在充分发挥高级氧化作用的同时，保证水基清洗剂最佳的传质、渗透和分散作用，有效实现了液晶盒残留液晶的高效清洗。