用聚(L-蛋氨酸)/纳米金修饰玻碳电极同时灵敏检测多巴胺和尿酸简

A novel electrochemical sensor was fabricated by electrodeposition of gold nanoparticles on a poly(L-methionine) (PMT)-modified glassy carbon electrode (GCE) to form a nano-Au/PMT composite-modified GCE (nano-Au/PMT/GCE). Scanning electron microscopy and electrochemical techniques were used to characterize the composite electrode. The modified electrode exhibited considerable electrocatalytic activity towards the oxidation of dopamine (DA) and uric acid (UA) in phosphate buffer solution (pH = 7.00). Differential pulse voltammetry revealed that the electrocatalytic oxidation currents of DA and UA were linearly related to concentration over the range of 5.0×10^-8 to 10^-6 mol/L for DA and 7.0×10^-8 to 10^-6 mol/L for UA. The detection limits were 3.7×10^-8 mol/L for DA and 4.5×10^-8 mol/L for UA at a signal-to-noise ratio of 3. According to our experimental results, nano-Au/PMT/GCE can be used as a sensitive and selective sensor for simultaneous determination of DA and UA.     

Poly(2-amino-5-(4-pyridinyl)-1, 3, 4-thiadiazole) film modified electrode for the simultaneous determinations of dopamine, uric acid and nitrite

Poly(2-amino-5-(4-pyridinyl)-1,3,4-thiadiazole) (PAPT) modified glassy carbon electrode (GCE) was fabricated and used for the simultaneous determinations of dopamine (DA), uric acid (UA) and nitrite (NO₂ ^?) in 0.1 mol?L^?1 phosphate buffer solution (PBS, pH 5.0) by using cyclic voltammetry and differential pulse voltammetry (DPV) techniques. The results showed that the PAPT modified GCE (PAPT/GCE) not only exhibited electrocatalytic activities towards the oxidation of DA, UA and NO₂ ^? but also could resolve the overlapped voltammetric signals of DA, UA and NO₂ ^? at bare GCE into three strong and well-defined oxidation peaks with enhanced current responses. The peak potential separations are 130 mV for DA–UA and 380 mV for UA–NO₂ ^? using DPV, which are large enough for the simultaneous determinations of DA, UA and NO₂ ^?. Under the optimal conditions, the anodic peak currents were correspondent linearly to the concentrations of DA, UA and NO₂ ^? in the ranges of 0.95–380 μmol?L^?1, 2.0–1,000 μmol?L^?1 and 2.0–1,200 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. The correlation coefficients were 0.9989, 0.9970 and 0.9968, and the detection limits were 0.2, 0.35 and 0.6 μmol?L^?1 for DA, UA and NO₂ ^?, respectively. In 0.1 mol?L^?1 PBS pH 5.0, the PAPT film exhibited good electrochemical activity, showing a surface-controlled electrode process with the apparent heterogeneous electron transfer rate constant (k _s) of 25.9 s^?1 and the charge–transfer coefficient (α) of 0.49, and thus displayed the features of an electrocatalyst. Due to its high sensitivity, good selectivity and stability, the modified electrode had been successfully applied to the determination of analytes in serum and urine samples.     

A Promising Electrochemical Platform for Dopamine and Uric Acid Detection Based on a Polyaniline/Iron Oxide-Tin Oxide/Reduced Graphene Oxide Ternary Composite

A ternary polyaniline/Fe₂O₃-SnO₂/reduced graphene oxide (PFSG) nanocomposite was prepared using a simple two-step hydrothermal treatment. The composite was applied as a glassy carbon electrode modifier (GCE) to enhance dopamine (DA) and uric acid (UA) detection. The ternary PFSG composite was compared with its binary precursor Fe₂O₃-SnO₂/reduced graphene oxide (FSG). The influence of the modified GCE electrodes on their performance as a sensing platform was determined. GCE/PFSG showed better sensing parameters than GCE/FSG due to the introduction of polyaniline (PANI), increasing the electrocatalytic properties of the electrode towards the detected analytes. GCE/PFSG enabled the detection of low concentrations of DA (0.076 µM) and UA (1.6 µM). The peak potential separation between DA and UA was very good (180 mV). Moreover, the DA oxidation peak was unaffected even if the concentration of UA was ten times higher. The fabricated sensor showed excellent performance in the simultaneous detection with DA and UA limits of detection: LOD_DA = 0.15 µM and LOD_UA = 6.4 µM, and outstanding long-term stability towards DA and UA, holding 100% and 90% of their initial signals respectively, after one month of use.     

Highly Sensitive and Selective Determination of Dopamine in the Presence of Ascorbic Acid Using Gold Nanoparticles‐Decorated MoS2 Nanosheets Modified Electrode

Herein, a novel nanocomposite has been synthesized by molybdenum disulfide (MoS₂) nanosheets and gold nanoparticles (AuNPs) via a microwave‐assisted hydrothermal method, which possesses the specific features of both MoS₂ and AuNPs. The AuNPs@MoS₂ nanocomposite modified electrode exhibits excellent electrocatalytic activity toward dopamine (DA). Its oxidation peak current shows a linear dependence over the DA concentration in the range from 0.1 to 200 µM, with a detection limit of 80 nM (S/N=3). More importantly, the AuNPs@MoS₂‐based sensor can detect DA in the presence of a large excess of ascorbic acid. The AuNPs@MoS₂‐based sensor shows good sensitivity, reproducibility and selectivity, suggesting that the AuNPs@MoS₂ nanocomposite is a promising candidate in electrochemical sensing and other electrocatalytic applications.     

A glassy carbon electrode modified with MoS<Subscript>2</Subscript> nanosheets and poly(3,4-ethylenedioxythiophene) for simultaneous electrochemical detection of ascorbic acid,dopamine and uric acid

We describe a chemical exfoliation method for the preparation of MoS₂ nanosheets. The nanosheets were incorporated into poly(3,4-ethylenedioxythiophene) (PEDOT) by electrodeposition on a glassy carbon electrode (GCE) to form a nanocomposite. The modified GCE is shown to enable simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA). Due to the synergistic effect of MoS₂ and PEDOT, this electrode displays better properties in terms of electrocatalytic oxidation of AA, DA and UA than pure PEDOT, which is illustrated by cyclic voltammetry and differential pulse voltammetry (DPV). Under optimum conditions and at pH 7.4, the respective sensitivities and best working potentials are as follows: AA: 1.20 A?mM^?1?m^?2, 30 mV; DA: 36.40 A?mM^?1?m^?2, 210 mV; UA: 105.17 A?mM^?1?m^?2, 350 mV. The calculated detection limits for AA, DA and UA are 5.83 μM, 0.52 μM and 0.95 μM, respectively. The modified electrode was applied to the detection of the three species in human urine samples and gave satisfactory results.

Open image in new window

Graphical abstract MoS₂ nanosheets were prepared by a facile chemical exfoliation method. MoS₂ and poly(3,4-ethylenedioxythiophene) nanocomposite modified glassy carbon electrodes were fabricated, which are shown to enable simultaneous determination of ascorbic acid, dopamine and uric acid with high sensitivity and selectivity.

     

Electrocatalytic Detection of Uric Acid on Nitrogen‐Doped Graphene Modified Electrode and Its Application

Nitrogen‐doped graphene (NG) was used to modify a glassy carbon electrode (GCE), which was applied to the voltammetric detection of uric acid (UA). Because of the presence of NG on the GCE surface, the modified electrode showed excellent electrocatalytic ability for UA oxidation with increase of the peak current and decrease of the peak potential. Compared to that of the traditional GCE, the overpotential of the oxidation peak decreased by 50 mV. Electrochemical performance of UA was studied on NG/GCE in detail, which showed a quasi‐reversible, diffusional‐controlled process. Electrochemical parameters including the charge transfer coefficient (α ), the number of electron transfer (n ), and the diffusional coefficient (D ) were calculated. At the optimal conditions, the oxidation peak current was linear, with UA concentration from 0.1 to 10.0 μmol/L as revealed by differential pulse voltammetry, and the detection limit was estimated as 0.042 μmol/L (3σ). The UA content in the urine sample of a healthy volunteer was determined by the proposed method with a recovery of 98.7–102.3%.     

Electropolymerization of Thin Film Conducting Polymer and Its Application for Simultaneous Determination of Ascorbic Acid,Dopamine and Uric Acid

In this paper electropolymerization of a thin film of para‐phenylenediamine (PPD) is studied at glassy carbon electrode (GCE) in sulfuric acid media by cyclic voltammetry. The results showed that this polymer was conducting and had a reproducible redox couple in the potential region from 0.0 to 0.4 V in phosphate buffer solution. This modified GCE (p‐PPD‐GCE) was applied for simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA) using differential pulse voltammetry (DPV). The p‐PPD‐GCE in 0.1 M phosphate buffer solution (pH 5.0) separated the DPV signals of AA, DA and UA with sufficient potential differences between AA–DA and DA–UA and also enhanced their oxidation peak currents. The oxidation currents were increased from 2.0 to 2000.0 µM for AA, 10.0 to 1250.0 µM for DA and 50.0 to 1600.0 µM for UA. The detection limits were evaluated as 0.4, 1.0 and 2.5 µM for AA, DA and UA, respectively (S/N=3).     

Development of a Carbon Paste Electrode Modified with Reduced Graphene Oxide and an Imidazole Derivative for Simultaneous Determination of Biological Species of N‐acetyl‐L‐cysteine,Uric Acid and Dopamine

In this work, the modified carbon paste electrode (CPE) with an imidazole derivative 2‐(2,3 dihydroxy phenyl) 4‐methyl benzimidazole (DHPMB) and reduced graphene oxide (RGO) was used as an electrochemical sensor for electrocatalytic oxidation of N‐acetyl‐L‐cysteine (NAC). The electrocatalytic oxidation of N‐acetyl‐L‐cysteine on the modified electrode surface was then investigated, indicating a reduction in oxidative over voltage and an intensive increase in the current of analyte. The scan rate potential, the percentages of DHPMB and RGO, and the pH solution were optimized. Under the optimum conditions, some parameters such as the electron transfer coefficient (α) between electrode and modifier, and the electron transfer rate constant) k_s) in a 0.1 M phosphate buffer solution (pH=7.0) were obtained by cyclic voltammetry method. The diffusion coefficient of species (D) 3.96×10^?5 cm² s^?1 was calculated by chronoamperometeric technique and the Tafel plot was used to calculate α (0.46) for N‐ acetyl‐L‐cysteine. Also, by using differential pulse voltammetric (DPV) technique, two linear dynamic ranges of 2–18 µM and 18–1000 µM with the detection limit of 61.0 nM for N‐acetyl‐L‐cysteine (NAC) were achieved. In the co‐existence system of N‐acetyl‐L‐cysteine (NAC), uric acid (UA) and dopamine (DA), the linear response ranges for NAC, UA, and DA are 6.0–400.0 µM, 5.0–50.0 µM and 2.0–20.0 µM, respectively and the detection limits based on (C=3s_b/m) are 0.067 µM, 0.246 µM and 0.136 µM, respectively. The obtained results indicated that DHPMB/RGO/CPE is applicable to separate NAC, uric acid (UA) and dopamine (DA) oxidative peaks, simultaneously. For analytic performance, the mentioned modified electrode was used for determination of NAC in the drug samples with acceptable results, and the simultaneous determination of NAC, UA and DA oxidative peaks was investigated in the serum solutions, too.     

Glassy Carbon Electrode Modified via Molybdenum Disulfide Decorated Multiwalled Carbon Nanotubes for Sensitive Voltammetric Detection of Aristolochic Acids

In this study, a molybdenum disulfide/multiwalled carbon nanotubes (MoS₂@MWCNTs) nanocomposite was synthesized by employing a simple hydrothermal method. The flower‐like structure of the MoS₂@MWCNTs was characterized via scanning electron microscopy (SEM) and transmission electron microscopy (TEM), and the load of crystalline MoS₂ was verified via X‐ray diffraction (XRD) and energy‐dispersive spectroscopy (EDS). The as‐prepared MoS₂@MWCNTs nanocomposite was used to modify glassy carbon electrode (GCE) as an electrochemical sensor for detecting aristolochic acids (AAs). With the optimized parameters, the proposed electrochemical sensor exhibited good sensitivity and a broad linear concentration range for detecting AAs from 0.2 to 10 μ mol/L and 10 to 100 μ mol/L, with the sensitivity of ?3.10 μ A/(μ mol/L) and ?0.91 μ A/(μ mol/L), respectively. The detection limit was also calculated as 0.06 μ mol/L (S/N=3) based on the low background signal. Furthermore, the modified electrochemical sensor exhibited good selectivity, repeatability, reproducibility, and stability, thus showing potential application for detecting AA in chinese herbs with good mean recovery and accuracy. In other words, the MoS₂@MWCNTs/GCE can be used as an excellent platform to detect AAs.     

Ascorbic acid amperometric sensor using a graphene-wrapped hierarchical TiO<Subscript>2</Subscript> nanocomposite

An ascorbic acid (AA) amperometric sensor was fabricated based on a glassy carbon electrode (GCE) modified with a reduced graphene oxide-wrapped hierarchical TiO₂ (RGO—TiO₂) nanocomposite. The RGO—TiO₂ nanocomposite was synthesized via the facial wet chemical method and characterized by scanning electron microscopy and X-ray diffraction. Cyclic voltammetry and amperometric techniques were employed to investigate its electrocatalytic performance towards the AA oxidation. The combined advantages of RGO and TiO₂ provide the electrode with higher current response and lower oxidation potential compared with those of bare GCE and TiO₂ modified GCE. The proposed electrode can be used for the determination of AA in the wide concentration range from 1 to 1500 µM with the detection limit of 0.5 µM. The proposed electrode was successfully used to determine AA in vitamin C tablets and spiked fruit juice.     

多巴胺在聚亚甲基蓝/石墨烯修饰电极上的电化学行为研究

利用电聚合方法在石墨烯修饰的玻碳电极表面制备了聚亚甲基蓝/石墨烯修饰电极(PMB/GH/GCE)。采用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了多巴胺(DA)和抗坏血酸(AA)在该修饰电极上的电化学行为。在pH 6.9的磷酸盐缓冲溶液中,DA和AA分别在0.208 V和-0.108 V处产生灵敏的氧化峰,与其在聚亚甲基蓝和石墨烯单层修饰电极上的电化学行为相比,两者的峰电流明显增加,峰电位差达316 mV。研究表明,电聚合方法使亚甲基蓝牢固地非共价修饰到石墨烯上,并产生协同增效作用,较好地提高了电极的灵敏度和分子识别性能,有利于在大量AA存在下实现对DA的选择性测定。在1.00×10-3mol/L AA的存在下,DA的差分脉冲伏安法峰电流与其浓度在1.00×10-7～5.00×10-3mol/L范围内呈良好的线性关系,检出限达1.00×10-8mol/L。将该方法用于盐酸多巴胺注射液的测定,结果满意。     

电聚合烟酰胺制备电化学传感器：同时测定多巴胺、尿酸和抗坏血酸

用循环伏安法（CV）选择不同电位区间来电聚合烟酰胺（NA）得到了两种聚合物膜修饰电极：poly-niacinamide/GCE (poly-NA/GCE)和poly- nicotinic acid /GCE (poly-NC/GCE)。这两电极都具有显著电化学催化作用,能明显地降低多巴胺（DA）、尿酸（UA）和抗坏血酸(AA)的氧化过电位,并在混合溶液中使这些物质的氧化峰电位距离足够大,可进行三物质的同时测定。poly-NC/GCE的电催化性能更好一些,用差分脉冲伏安法（DPV）测定抗坏血酸,线性范围为75–3000 µmol L-1,电流灵敏度为5.6 mA•L•mol-1;测定多巴胺,线性范围为0.37 – 16 µmol L-1,电流灵敏度为1140 mA•L•mol-1; 测定尿酸,线性范围为0.74 – 230 µmol L-1,电流灵敏度为102 mA•L•mol-1。该电极具有很高的灵敏度、选择性和抗污染能力。     

多巴胺在聚钙羧酸膜修饰碳糊电极上的电催化及与尿酸的同时测定

采用循环伏安法(CV)制备了聚钙羧酸(PCCA)膜修饰的碳糊电极(CPE)。考察了电极对多巴胺(DA)、尿酸(UA)的电氧化催化性能。结果显示,聚钙羧酸膜修饰碳糊电极(PCCA/CPE)对DA有良好的电催化效果,DA呈现出一对准可逆的氧化还原峰,氧化峰电流与DA浓度在3.0×10-7～1.0×10-4mol/L范围内呈线性关系,检出限为1×10-7mol/L(S/N=3)。使用微分脉冲伏安法(DPV),DA和UA在PCCA/CPE上的氧化峰能完全分离(ΔEp=192 mV),且峰电流与浓度均呈现良好的线性关系,可实现对DA和UA的同时测定。实验还进行了实际样品测定。     

One-pot solvothermal synthesis of a Cu2O/Graphene nanocomposite and its application in an electrochemical sensor for dopamine

Nanocomposites composed of cuprous oxide (Cu₂O) and graphene were synthesized via reduction of copper(II) in ethylene glycol. This material possesses the specific features of both Cu₂O and graphene. Its morphology was characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and X-ray photoelectron spectroscopy. Cyclic voltammetry was used to evaluate the electrochemical response of a glass carbon electrode (GCE) modified with the nanocomposite towards dopamine (DA). Compared to the bare GCE, the Cu₂O nanoparticles modified electrode and the graphene modified electrode, the nanocomposites modified electrode displays high electrocatalytic activity in giving an oxidation peak current that is proportional to the concentration of DA in the range from 0.1 to 10???M,with a detection limit of 10?nM (S/N?=?3). The modified electrode shows excellent selectivity and sensitivity even in the presence of high concentration of uric acid and can be applied to determine DA in real samples with satisfactory results.

纳米金/石墨烯修饰电极的制备及其对多巴胺的测定

利用电化学还原方法制备纳米金/石墨烯修饰玻碳电极,研究了多巴胺(DA)在该修饰电极上的电化学行为,建立了电化学测定多巴胺的新方法。结果表明,在磷酸盐缓冲溶液中,此修饰电极对多巴胺的电化学响应具有很好的催化作用。利用差示脉冲伏安技术对多巴胺的电化学氧化进行定量分析,多巴胺的氧化峰电流与其浓度在1.0×10-7～1.0×10-5mol/L范围内呈良好的线性关系,检测限低至4.0×10-8mol/L。该修饰电极适于多巴胺的分析检测。     

电氧化异丙肾上腺素的纳米复合电催化剂：用作传感器

在金纳米粒子(AuNPs)上经苯硫酚衍生物(3,4二羟基苯基-偶氮-苯硫酚, DAT)自组装制得了一种新型纳米复合物,用于修饰玻璃碳电极(GCE/AuNP-DAT).采用循环伏安法研究了该新型电极的性质,并将其用作异丙肾上腺素(IP)电催化剂,考察了该纳米复合物的电催化活性,从而得到反应机理和催化反应速率常数.由于GCE/AuNP-DAT电极对尿酸氧化没有电催化活性,因此可将IP的氧化信号从该改进电极中分离出来,从而排除了尿酸对IP测定的干扰.该电极可作为传感器,当用于差动脉冲伏安法测定IP时,线性动态范围为1.0–1500.0μmol/L,检测极限为0.46μmol/L.     

Electrochemical reduced graphene oxide-poly(eriochrome black T)/gold nanoparticles modified glassy carbon electrode for simultaneous determination of ascorbic acid,dopamine and uric acid

This work reports on the preparation of electrochemically reduced graphene oxide (ERGO)-poly(eriochrome black T) (pEBT) assembled gold nanoparticles for the simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA) in PBS pH 6.0. Characterisations of the composite were carried out by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. As a result of the synergistic effect, the modified glassy carbon electrode (GCE) possessed an efficient electrochemical catalytic activity with a high selectivity and sensitivity in oxidising AA-DA and DA-UA as compared to the bare GCE. The peak separations of AA and DA, DA and UA were 183 mV and 150 mV, respectively. The linear response ranges for AA, DA and UA were 10–900 μM, 0.5–20 μM and 2–70 μM with detection limits of 0.53 μM, 0.009 μM and 0.046 μM (S/N = 3), respectively. The sensitivity of ERGO-pEBT/AuNPs was measured as 0.003 µA/μM, 0.164 µA/μM and 0.034 µA/μM for AA, DA, and UA, respectively. The modified electrochemical sensor was used in the determination of AA, DA, and UA in vitamin C tablets and urine sample with good recovery.     

Direct electrochemistry of hemoglobin on graphene/Fe3O4 nanocomposite-modified glass carbon electrode and its sensitive detection for hydrogen peroxide

Graphene/Fe₃O₄ nanocomposite was prepared for the immobilization of hemoglobin (Hb) to improve the electron transfer between Hb and glass carbon electrode (GCE). The characterization of nanocomposites was described by transmission electron microscopy, Fourier transform infrared, Raman spectroscopy, and X-ray photoelectron spectroscopy, respectively. The electrochemistry of Hb on the graphene/Fe₃O₄-based GCE was investigated by cyclic voltammetry and amperometric measurement. The modified electrode showed a wide linear range from 0.25 μmol/L to 1.7 mmol/L with a correlation coefficient of 0.9967. The detection limit of the H₂O₂ biosensor was estimated at 6.0?×?10^?6?mol/L at a signal-to-noise ratio of 3.     

Preparation of aminylferrocene/nanogold modified glassy carbon electrode and its electrocatalysis on dopamine

Aminylferrocene(FcAI)-Nanogold(NG) modified glassy carbon electrode (FcAI/NG/GCE) was prepared by the Au-N bond between Au and FcAI. Electrochemical impedance spectroscopy (EIS) was employed to study the surface of the modified electrode. The electrochemical behavior of dopamine (DA) on the modified electrode was investigated and it was found that the modified electrode had an obvious electrocatalytic effect on DA. Compared with a bare GCE, the modified electrode exhibited an apparent shift of the oxidation peak potential in the negative potential direction and a marked enhancement in the current response for DA. We investigated the determination of DA on the modified electrode by differential pulse voltammetry (DPV). Linear calibration curve was obtained in the range of 7.0 x 10(-7) mol/L to 6x10(-4) mol/L of DA in 0.1 mol/L phosphate buffer solution (pH = 7.0) with a correlation coefficient of 0.9989. The detection limit (S/N = 3) of DA was estimated to be 1.0 x 10(-7) mol/L. Especially, by using the modified electrode, we can separate the oxidation peaks of ascorbic acid (AA) and DA in the PBS and it was satisfactory for the determination of DA with the interference of AA.     

Selective Detection of Dopamine in the Presence of Uric Acid Using NiO Nanoparticles Decorated on Graphene Nanosheets Modified Screen‐printed Electrodes

A convenient, low cost, and sensitive electrochemical method, based on a disposable graphene nanosheets (GR) and NiO nanoparticles modified carbon screen printed electrode (NiO/GR/SPE), is described for the simultaneous determination of dopamine (DA) and uric acid (UA). The modified electrode exhibited good electrocatalytic properties toward the oxidation of DA and UA. A peak potential difference of 150 mV between DA and UA was large enough to determine DA and UA individually and simultaneously. The anodic peak currents of DA were found to be linear in the concentration range of 1.0–500.0 μM with the detection limit of 3.14×10^?7 M.