Effect of maleic anhydride grafted polypropylene on the mechanical and morphological properties of chemically modified short‐pineapple‐leaf‐fiber‐reinforced polypropylene composites

With the rising cost of petroleum‐based fibers, the utilization of plant fibers in the manufacture of polymer–matrix composites is gaining importance worldwide. The scope of this study was to examine the perspective of the use of pineapple leaf fibers (PALFs) as reinforcements for polypropylene (PP). These fibers are environmentally friendly, low‐cost byproducts of pineapple cultivation and are readily available in the northeastern region of India. Here, both untreated and treated pineapple fibers were used. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as a compatibilizing agent. The polymer matrix of PP was used to prepare composite specimens with different volume fractions (5–20%) of fibers by the addition of 5% of MA‐g‐PP. These specimens were tested for their mechanical properties, and additional assessments were made via observations by scanning electron microscopy, thermogravimetric analysis, and IR spectroscopy. Increase in the impact behavior, flexural properties, and tensile moduli of the composites were noticed, and these were more appreciable in the treated fibers mixed with MA‐g‐PP. PALF in 10 vol % in PP mixed with MA‐g‐PP was the optimum and recommended composition, where the flexural properties were the maximum. The impact strength and the tensile modulus were also considerably high. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal and mechanical properties of polypropylene/wood‐flour composites

In this research, polypropylene/wood‐flour composites (WPCs) were blended with different contents of wood and/or maleated polypropylene (MAPP) and clay. We found that the addition of MAPP or clay in the formulation greatly improved the dispersion of the wood fibers in the composite; this suggested that MAPP or clay may have played the role of an adhesion promoter in the WPCs. The results obtained with clay indicate that it also acted as a flame retardant. The thermal tests carried out with the produced samples showed an increased crystallization temperature (T_c), crystallinity, and melting temperature (T_m) with wood loading. The increase of the two former parameters was explained by the incorporation of wood flour, which played the role of nucleating agent and induced the crystallization of the matrix polymer. On the other hand, the T_m increase was ascribed to the insulating properties of wood, which hindered the movement of heat conduction. The effects of UV irradiation on T_m and T_c were also examined. T_c increased with UV exposure time; this implied that UV degradation generated short chains with low molecular weight that could move easily in the bulk of the sample and, thus, catalyze early crystallization. The flexural strength and modulus increased with increasing wood‐flour content. In contrast, the impact strength and tensile strength and strain decreased with increasing wood‐flour content. All of these changes were related to the level of dispersion of the wood flour in the polymeric matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of material parameters on the diffusion and sorption properties of wood‐flour/polypropylene composites

Composites of wood in a thermoplastic matrix (wood–plastic composites) are considered a low maintenance solution to using wood in outdoor applications. Knowledge of moisture uptake and transport properties would be useful in estimating moisture‐related effects such as fungal attack and loss of mechanical strength. Our objectives were to determine how material parameters and their interactions affect the moisture uptake and transport properties of injection‐molded composites of wood‐flour and polypropylene and to compare two different methods of measuring moisture uptake and transport. A two‐level, full‐factorial design was used to investigate the effects and interactions of wood‐flour content, wood‐flour particle size, coupling agent, and surface removal on moisture uptake and transport of the composites. Sorption and diffusion experiments were performed at 20°C and 65 or 85% relative humidity as well as in water, and diffusion coefficients were determined. The wood‐flour content had the largest influence of all parameters on moisture uptake and transport properties. Many significant interactions between the variables were also found. The interaction between wood‐flour content and surface treatment was often the largest. The diffusion coefficients derived from the diffusion experiments were different from those derived from the sorption experiments, suggesting that different mechanisms occur. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 752–763, 2007     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Studies on grafting of acrylic acid onto polypropylene melt‐blown nonwovens induced by electron‐beam preirradiation

We report the graft copolymerization of acrylic acid onto the polypropylene (PP) melt‐blown nonwovens induced by electron beam (EB) preirradiation in this article. The occurrence of the graft copolymerization was confirmed by means of XPS, FTIR, and SEM. The effects of preirradiation dose, monomer concentration, bath ratio, reaction time, and temperature on the graft ratio were investigated. The water conservation, water absorption rate, and K⁺ exchange capacity were also determined on the grafted PP melt‐blown nonwovens, which showed that EB preirradiation‐induced grafting was an effective way to improve the hydrophicility of PP melt‐blown nonwovens. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4971–4977, 2006     

Effect of bark flour content on the hygroscopic characteristics of wood–polypropylene composites

The effects of the bark content on the water absorption and thickness swelling of wood–plastic composites prepared from polypropylene, wood flour, and bark flour were studied. Samples were made with a laboratory twin‐screw extruder. The results showed that among composites free of maleic anhydride polypropylene, those composites containing a higher bark flour content exhibited lower water absorption and lower thickness swelling. Maleic anhydride polypropylene reduced water absorption and thickness swelling in composites containing wood flour and a lower content of bark flour but had no influence on the hygroscopic properties of composites made with higher bark contents. Adding maleic anhydride polypropylene had no effect on the water diffusion coefficients and swelling rate parameters of composites made with a higher bark flour content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Syndiotactic polypropylene/microfibrous cellulose composites: Effect of filler size on tensile properties

Syndiotactic polypropylene (SPP)/ethanol swelled microfibrous cellulose (MFC) composite was prepared by a melting mixer, and its morphology and tensile properties were studied. The scanning electron microscope microphotograph did not show the aggregated MFC part up to the 40 wt % MFC loading content, and the Young's modulus was exponentially increasing with the increase of the MFC loading content. These results suggested that the MFC was well‐dispersed in the SPP matrix by an ethanol surfactant work. The Young's modulus was much higher than that of the composite with commonly used fibrous cellulose and moreover, exceeded the theoretical one obtained from the Halpin‐Tsai equation. The differential scanning calorimetry and wide‐angle X‐ray diffraction measurements showed that the MFC acted as a good α‐nucleation agent for SPP. It was found that the excessive Young's modulus of the MFC composite was originated from an increase of that of the SPP matrix induced by the α‐nucleation effect. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation,structure, and property of wood flour incorporated polypropylene composites prepared by a solid‐state mechanochemical method

In this article, a solid‐state mechanochemical method based on a pan‐mill equipment was used to prepare 60 wt % loading of wood flour (WF) incorporated polypropylene (PP) wood–plastic composite (WPC) with good comprehensive performance. The particle size distribution, crystallization, microstructure, and properties of the prepared WPC were accordingly investigated. The results show that under co‐effects of the strong shear force field of pan milling and the compatibilization of PP grafted maleic anhydride (PP‐g‐MAH), the mixture of PP and WF is effectively pulverized and homogeneously mixed. Meanwhile, the WF particles are adequately activated by exposure of their characteristic functional groups, which is beneficial to the interfacial mechanochemical reaction. PP‐g‐MAH and PP prove to be in situ grafted onto WF particles surface during pan milling, thus resulting in the substantial enhancement in both the dispersion of the added WF fillers in PP matrix and the interfacial bonding. The mechanochemical effects of pan milling could also remarkably promote the heterogeneous nucleation effect of WF particles on PP crystallization and influence the dynamic mechanical behavior of composite. Compared with the unmilled and uncompatibilized composite, the milled and compatibilized WPC material possesses greatly enhanced mechanical performance and shows good application prospects. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43108.     

Maleic anhydride grafted polypropylene as a coupling agent for polypropylene composites filled with ink‐eliminated waste paper sludge flour

Ink‐eliminated sludge flour (IESF), a waste residue from the recycling treatment of waste paper, is a promising new kind of filler for thermoplastic polymers with a good price/performance ratio and advantages for environmental protection. In this study, high‐impact polypropylene (PP) and maleic anhydride grafted polypropylene (MAPP) were chosen as a polymer matrix and a coupling agent, respectively, for the preparation of IESF/PP composites, and the structures and properties of the obtained composites were also investigated. The experimental results revealed that IESF not only induced the crystallization orientation of PP along the b axis but also had a restraining effect on the formation of the β phase during the recrystallization of PP from the melt; the addition of MAPP further strengthened this effect to some extent. In addition, the proper addition of MAPP was helpful for improving the thermal stability of the IESF/PP composites. With the strengthening of the interfacial interaction between the IESF and PP matrix by MAPP, the resultant efficient stress transfer from the PP matrix to the IESF particles led to increased tensile and flexural strength. However, the original greater rigidity of MAPP, with respect to PP, reduced the toughness of the composites and caused some negative effects on the impact strength and the elongation at break. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2320–2325, 2004     

Comparative study of maleated polypropylene as a coupling agent for recycled low‐density polyethylene/wood flour composites

The effects of the type of coupling agent and virgin polypropylene (PP) content on the mechanical properties and water absorption behavior of recycled low‐density polyethylene/wood flour (WF) composites were investigated. The fractured surfaces of these recycled wood/plastic composites (rWPCs) were examined to gain insight into the distribution and dispersion of WF within the polymer matrix. The results indicate that the use of 100% recycled polymer led to inferior mechanical properties and to a greater degree of moisture absorption and swelling when compared to recycled polymer–virgin PP wood/plastic composites. This could have been related to the poor melt strength and inferior processability of the recycled polymer. The extent of improvement of the mechanical properties depended not only on the virgin PP content in the matrix but also on the presence of maleic anhydride (MA) modified PP as the coupling agent. Higher concentrations of MA group were beneficial; this improvement was attributed to increased chemical bonding (ester linkages) between hydroxyl moieties in WF and anhydride moieties in the coupling agent. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology,deformation behavior and thermomechanical properties of polypropylene/maleic anhydride grafted polypropylene/layered silicate nanocomposites

Nanocomposites polypropylene (PP) with 3 and 7 wt % of clay were prepared by melt mixing. Four types of maleic anhydride grafted PP (MAPP) in broad range of MA groups content (0.3–4 wt %) and molecular weights (MW) were used as polar compatibilizers. The effect of the MAPP kind on both the clay dispersion and miscibility with PP was studied. The mixed intercalated/exfoliated morphologies of nanocomposites in the presence of all studied compatibilizers were revealed by XRD and TEM. The oligomer compatibilizer with 4 wt % of MA groups increases the intercalation ability of polymer into clay galleries but this one has limited miscibility with PP and worsens crystalline structure of polymer matrix. The MAPPs with 0.3–1.3% of MA are characterized by the lower intercalation ability but well cocrystallize with PP. Maximum reinforcing effect is attained using high MW MAPP with 0.6% MA and for nanocomposite with 7 wt % (3.8 vol %) of clay it averages almost 1.7 times relative to neat PP and 1.3 times relative to noncompatibilized composite. Dynamic storage moduli of nanocomposites compatibilized by MAPPs with 0.3–1.3% of MA containing 7 wt % of clay increase up to 1.4–1.5 around 30–75°C and over the whole temperature range remain higher compared with both neat PP and uncompatibilized composite. On the contrary, the oligomer MAPP with 4 wt % of MA groups decreases the thermal–mechanical stability of nanocomposite at high temperature compared with both PP and uncompatibilized composites. The study of nanocomposites flammability showed that creating complex composites containing both layered silicate and relatively small amount of magnesium hydroxide can be a successful approach to reduce the combustibility of PP‐based nanocomposites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation of HDPE/SEBS‐g‐MAH and its effect on mechanical properties of HDPE/wood flour composites

In this article, high density polyethylene/styrene‐ethylene‐butylene‐styrene block copolymer blends (HDPE/SEBS) grafted by maleic anhydride (HDPE/SEBS‐g‐MAH), which is an effective compatibilizer for HDPE/wood flour composites was prepared by means of torque rheometer with different contents of maleic anhydride (MAH). The experimental results indicated that MAH indeed grafted on HDPE/SEBS by FTIR analysis and the torque increased with increasing the content of maleic anhydride and dicumyl peroxide (DCP). Styrene may increase the graft reaction rate of MAH and HDPE/SEBS. When HDPE/SEBS MAH was added to HDPE/wood flour composites, tensile strength and flexural strength of composites can reach 25.9 and 34.8 MPa in comparison of 16.5 and 23.8 MPa (without HDPE/SEBS‐g‐MAH), increasing by 157 and 146%, respectively. Due to incorporation of thermoplastic elastomer in HDPE/SEBS‐g‐MAH, the Notched Izod impact strength reached 5.08 kJ m^?2, increasing by 145% in comparison of system without compatibilizer. That HDPE/SEBS‐g‐MAH improved the compatibility was also conformed by dynamic mechanical measurement. Scanning electron micrographs provided evidence for strong adhesion between wood flour and HDPE matrix with addition of HDPE/SEBS‐g‐MAH. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

The effect of maleic anhydride grafting efficiency on the flexural properties of polyethylene composites

Many authors have reported on the property enhancements possible by compounding high density polyethylene (HDPE) with fillers to produce composites. It is accepted that polyethylene combined with materials such as nanoclay or wood flour will not yield favorable properties unless a compatibilizing material is used to form a link. In this work, compatibilized HDPE was produced by grafting maleic anhydride (MA) to its backbone in a twin screw extruder using a peroxide initiated reactive process. Fourier transform infrared spectroscopy (FTIR) was used to examine the effects of varying peroxide and MA levels on the grafting percentage and it was found that a high percentage could be achieved. The gel content of each HDPE‐g‐MA batch was determined and twin bore rheometry analysis was carried out to examine the effects of crosslinking and MA grafting on the melt viscosity. These HDPE‐g‐MA compatibilizers were subsequently compounded with nanoclay and wood flour to produce composites. The composite materials were tested using a three point bending apparatus to determine the flexural modulus and strength and were shown to have favorable mechanical properties when compared with composites containing no compatibilizer. X‐ray diffraction (XRD) was used to examine the effects of grafted MA content on the intercalation and exfoliation levels of nanoclay composites. The results from XRD scans showed that increased intercalation in polymer nanoclay composites was achieved by increasing the grafted MA content. This was confirmed using a scanning electron microscope, where images produced showed increased levels of dispersion and reductions in nanoclay agglomerates. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Evaluation of dynamic elastic properties of wood‐filled polypropylene composites

Dynamic modulus of elasticity (MoE) and shear modulus of wood‐filled polypropylene composite at various filler contents ranging from 10% to 50% was determined from the vibration frequencies of disc‐shaped specimens. Wood filler was used in both fiber form (pulp) and powder form (wood flour). A novel compatibilizer, m‐isopropenyl‐α,α‐dimethylbenzyl‐isocyanate(m‐TMI) grafted polypropylene with isocyanate functional group was used to prepare the composites. A linear increase in dynamic MoE, shear modulus, and density of the composite was observed with the increasing filler content. Between the two fillers, wood fiber filled composites exhibited slightly better properties. At 50% filler loading, dynamic MoE of the wood fiber filled composite was 97% higher than that of unfilled polypropylene. Halpin‐Tsai model equation was used to describe the changes in the composite modulus with the increasing filler content. The continuous improvement in elastic properties of the composites with the increasing wood filler is attributed to the effective reinforcement of low‐modulus polypropylene matrix with the high‐modulus wood filler. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1706–1711, 2006     

Modification of wood flour/PLA composites by reactive extrusion with maleic anhydride

MA modified wood flour/PLA composites were prepared by one‐step reactive extrusion, in which wood flour and poly(lactic acid) (PLA) were used as raw material, maleic anhydride (MA) was used as modifier, and dicumyl peroxide (DCP) was used as initiator. The influences of MA concentration on the morphology, thermal stability, rheological, and mechanical properties of the composites were studied. The addition of MA improved the compatibility of the composites significantly. The thermal and rheological results showed that with the increase of the concentration of MA, the thermal stability of the composites decreased, the storage modulus and complex viscosity of the composites also decreased. The MA modified composites had an enhanced mechanical strength compared to the unmodified one. As the concentration of the MA increased, the tensile and flexural strength of the composites first increased and then decreased, and reached a maximum when the concentration of MA was 1 wt %. The MA modified composites showed a better water resistance than the unmodified ones. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43295.     

马来酸酐接枝 SEBS对聚丙烯 / 碳纳米管复合材料性能的影响

采用球磨和熔融共混法，制备了聚丙烯（PP）／碳纳米管（CNT）／马来酸酐接枝SEBS（MA－SEBS）复合材料，结果表明，MA－SEBS促进了CNT在PP基体中的分散，形成完善的逾渗网络，改善了PP／CNT复合材料的抗静电性，提高了CNT对PP的增强作用，对PP／CNT复合材料有明显的增韧作用。     

Rice husk/poly(propylene‐co‐ethylene) composites: Effect of different coupling agents on mechanical,thermal, and morphological properties

Poly(propylene‐co‐ethylene) composites with rice husk were prepared in a corotating intermeshing twin‐screw extruder using four different coupling agents. While modified maleic anhydrides such as maleated polypropylene (MAPP) and maleated polyethylene (MAPE) are commonly used as compatibilizers to improve interfacial adhesion between lignocellulosic filler and matrix, in this study, polypropylene grafted with acid comonomer (CAPP) and high‐density polyethylene grafted with acid comonomer (CAPE) were also used. The morphologies and the thermal and mechanical properties of the composites were characterized using scanning electron microscopy, thermogravimetric analysis, differential scanning analysis, tensile and impact tests. The results indicate that the base resin of the compatibilizer is an important factor in determining the effectiveness of compatibilizers for composites. Composites with PP‐based compatibilizers are more effective than PE‐based compatibilizers due to the improved wetting of the former compatibilizer in the matrix polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

The effect of epoxy and tetramethyl thiuram disulfide on melt‐grafting of maleic anhydride onto polypropylene by reactive extrusion

In this report, melt grafting of maleic anhydride (MAH) and epoxy resin onto polypropylene (PP) by peroxide‐initiated reactive extrusion has been investigated. As evidenced by Fourier transform infrared spectroscopy, both MAH and epoxy resin were successfully grafted onto PP through the reactions of MAH with PP and epoxy resin with MAH. It was found that tetramethyl thiuram disulfide could promote the grafting of MAH and inhibit the degradation of PP, as revealed by chemical titration and melt flow experiments, through prolonging the lifetime of the macroradical; meanwhile, epoxy resin could reduce the sublimation of MAH and the maximum grafting degree of MAH. Furthermore, the introduction of grafted products was found to enhance the mechanical properties of PP/glass fiber composites, and this influence was very significant at high grafting degrees with a high content of epoxy resin, which could be interpreted in terms of improved compatibility and adhesion at the interface. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43422.     

Polyolefin composites with natural fibers and wood‐modification of the fiber/filler–matrix interaction

Numerous strategies to improve the fiber–matrix interaction in natural fiber composites (NFCs) and wood polymer composites (WPCs) have been proposed and investigated. We have reviewed literature on polyolefin‐based NFCs and WPCs to get an overview of the current state of the art of compatibilization methods. Those are classified in two categories here, namely fiber‐based strategies and matrix‐based strategies. Although this issue has been covered by several reviews before, as yet no work exists that is focused on polyolefin‐based NFCs and WPCs. Furthermore, a ranking of the compatibilization methods based on their effects on material properties such as tensile/flexural strength and modulus, impact strength and water absorption, allows for an assessment of the efficiency of the various methods. As to the fiber‐based strategies, silanes, maleated polyolefins (MA‐POs), mercerization and acetylation are most thoroughly investigated. Silanes are most effective judged by achievable material property improvements, allowing for increases in tensile and flexural strength of more than 100%. Among the matrix‐based strategies, MA‐POs and isocyanates are most prominent in the literature. The first class enables the more significant material improvements, with reported increases of tensile and flexural strength of 132% and 85%, respectively. While strengths can be enhanced by many compatibilization methods, moduli, and impact strength (notched in particular) are in most cases improved to a lesser degree or even reduced. Especially, the last point calls for further attention, because impact strength is still a weak point of NFCs and WPCs. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2013     

Modification of oil palm empty fruit bunches with maleic anhydride: The effect on the tensile and dimensional stability properties of empty fruit bunch/polypropylene composites

Oil palm empty fruit bunch (EFB)‐filled polypropylene (PP) composites were produced. The EFB filler was chemically modified with maleic anhydride (MAH). The effects of the filler size and chemical modification of EFBs on the tensile and dimensional stability properties of EFB–PP composites were studied. The composites with MAH‐treated EFBs showed higher tensile strengths than those with untreated EFBs. This was attributed to the enhanced compatibility between the MAH‐treated EFBs and PP matrix, as shown in a scanning electron microscopy study. Fourier transform infrared analysis showed evidence of C?C and C?O bonds from MAH at 1630 and 1730 cm^?1, respectively. The MAH‐treated PP composites showed lower water absorption and thickness swelling than those with untreated EFBs. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 827–835, 2003