Detection of liquid petroleum gas using mixed nanosized tungsten oxide-based thick-film semiconductor sensor

The thick-film semiconductor sensor for liquid petroleum gas (LPG) detection was fabricated using a mixed WO₃-based sensor. We present the characterization of both their structural properties by means of XRD measurements and the electrical characteristics by using gas-sensing properties. The sensing characteristics such as sensitivity, working range, cross-sensitivity and response time were studied by using nanosized WO₃-based mixed with different metal oxides (SnO₂, TiO₂ and In₂O₃) and doped with noble metals (Au, Pd and Pt). The WO₃-based mixed with 5 wt.% In₂O₃ and 0.5 wt.% Pd showed the higher sensing characteristic at low concentration of LPG sensor at an operating temperature 225 °C.     

Gd-N共掺杂SrTiO3/TiO2复合纳米纤维制备及光催化性能

以静电纺丝技术制备的TiO_2纳米纤维为基质和反应物,结合一步水热法制得Gd-N共掺杂SrTiO_3/TiO_2复合纳米纤维光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、高分辨透射电镜(HRTEM)、X射线光电子能谱(XPS)、紫外-可见漫反射(UV-Vis DRS)和荧光光谱(PL)等方法对其微观结构、形貌和光学性能进行表征。结果表明:SrTiO_3和TiO_2形成异质结能够使光生电子和空穴得到很好的分离,而Gd-N共掺杂产生新带隙,可以拓宽光谱响应范围至可见光区,并引起晶格缺陷,成为光生电子-空穴对的浅势捕获阱。Gd-N共掺杂与异质结的协同作用有效提高了SrTiO_3/TiO_2复合纳米纤维的可见光催化活性。     

Detection of nitrogen dioxide using mixed tungsten oxide-based thick film semiconductor sensor

The thick film semiconductor sensor for NO₂ gas detection was fabricated by screen-printing method using a mixed WO₃-based as sensing material. The sensing characteristics, such as response time, response linearity, sensitivity, working range, cross sensitivity, and long-term stability were further studied by using a WO₃-based mixed with different metal oxides (SnO₂, TiO₂ and In₂O₃) and doped with noble metals (Au, Pd and Pt) as sensing materials was observed. The highest sensitivity for low concentrations (<16 mg l⁻¹) was observed using WO₃-based mixed with In₂O₃ or TiO₂. The NO₂ gas sensor showing the fastest response and recovery time (both within 2 min), good linearity (Y=0.606X+0.788 R²=0.991) for gas concentrations from 3 to 310 mg l⁻¹, low resistance (3 MΩ), high sensitivity, undesirable cross sensitivity effect and good long-term stability (at least 120 days) using WO₃-SnO₂-Au as sensing material.     

Preparation and visible light photocatalytic activity of Bi2O3/Bi2WO6 heterojunction photocatalysts

The Bi₂O₃/Bi₂WO₆ heterojunction photocatalysts were prepared by a two-step solvothermal process using Bi(NO₃)₃-ethylene glycol solution as Bi source. The catalysts were characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-vis diffuse reflection spectroscopy. The heterostructure catalysts are composed of Bi₂O₃ nanoparticles as modifier and 3D Bi₂WO₆ microspheres as substrate. Bi₂O₃ nanoparticles with diameters of about 10-15 nm are tightly grown on the lateral surface of the Bi₂WO₆ microspheres. The hierarchical Bi₂O₃/Bi₂WO₆ microspheres exhibit higher photocatalytic activity than the single phase Bi₂WO₆ or Bi₂O₃ for the degradation of rhodamine B under visible light illumination (λ>420 nm). The enhancement of the photocatalytic activity of the Bi₂O₃/Bi₂WO₆ heterojunction catalysts can be ascribed to their improved light absorption property and the reduced recombination of the photoexcited electrons and holes during the photocatalytic reaction. The effect of loading amount of Bi₂O₃ on the catalytic performance of the heterojunction catalysts was also investigated and the optimal content of Bi₂O₃ is 3 wt%. The Bi₂O₃/Bi₂WO₆ heterojunction photocatalysts are essentially stable during the photocatalytic process.     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Acetone vapor sensing properties of screen printed WO3 thick films

This paper presents acetone vapor sensing properties of WO₃ thick films. In this work, the WO₃ thick films were prepared by standard screen-printing method. These films were characterized by X-ray diffraction (XRD) measurements, and scanning electron microscopy (SEM). The acetone vapor sensing properties of these thick films were investigated at different operating temperature and acetone vapor concentrations. The WO₃ thick films exhibit excellent acetone vapor sensing properties with the maximum sensitivity ∼456% at 300 °C in air atmosphere with fast response and recovery time.     

Bi2Ti2O7/TiO2复合纤维：原位水热合成及光催化性能

采用静电纺丝技术制备的TiO2纤维作为模板和反应物,通过原位水热合成了具有异质结构的Bi2Ti2O7/TiO2复合纤维。利用X射线衍射(XRD)、扫描电镜(SEM)、能量散射光谱(EDS)、高分辨透射电镜(HRTEM)和紫外可见吸收光谱(UV-Vis)等分析测试手段对样品的结构和形貌进行表征。以罗丹明B为模拟有机污染物进行光催化降解实验。结果表明:花状Bi2Ti2O7纳米结构均匀地生长在TiO2纤维上,制备了Bi2Ti2O7与TiO2相复合的光催化材料,其光谱响应范围拓宽至可见光区,与纯TiO2纤维相比可见光催化活性显著提高,且易于分离、回收和循环使用。初步探讨了Bi2Ti2O7/TiO2异质结的生长机制和光催化活性提高机理。     

The effects of solvent on photocatalytic properties of Bi2WO6/TiO2 heterojunction under visible light irradiation

Bi₂WO₆/TiO₂ heterojunction photocatalysts with two different microstructures were controllably fabricated via a facile two-step synthetic route. XRD, XPS, SEM, TEM, BET-surface, DRS, PL spectra, photoelectrochemical measurement (Mott-Schottky), and zeta-potential analyzer were employed to clarify structural and morphological characteristics of the obtained products. The results showed that Bi₂WO₆ nanoparticles/nanosheets grew on the primary TiO₂ nanorods. The TiO₂ nanorods used as a synthetic template inhibit the growth of Bi₂WO₆ crystals along the c-axis, resulting in Bi₂WO₆/TiO₂ heterostructure with one-dimensional (1D) morphology. The photocatalytic properties of Bi₂WO₆/TiO₂ heterojunction photocatalysts were strongly dependent on their shapes and structures. Compared with bare Bi₂WO₆ and TiO₂, Bi₂WO₆/TiO₂ composite have stronger adsorption ability and better visible light photocatalytic activities towards organic dyes. The Bi₂WO₆/TiO₂ composite prepared in EG solvent with optimal Bi:Ti ratio of 2:12 (S-TB2) showed the highest photocatalytic activity, which could totally decompose Rhodamine B within 10 min upon irradiation with visible light (λ > 422 nm), and retained the high photocatalytic performance after five recycles, confirming its stability and practical usability. The results of PL indicated that Bi₂WO₆ and TiO₂ could combine well to form a heterojunction structure which facilitated electron–hole separation, and lead to the increasing photocatalytic activity.     

Preparation and Characterisation of Nano-Structured WO<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Layers for Photoelectrochromic Devices

Nano-structured WO₃-TiO₂ layers were prepared by the sol-gel route. To obtain transparent, porous and crack free layers up to 0.8 μ m with a single dipping cycle a templating strategy was used. As a template three-dimensionally network based on organically modified silane was introduced to the WO₃ and TiO₂ sols. The WO₃ layers were dip-coated onto the conductive glass substrate (TCO) and the TiO₂ layers on the top of the WO₃ layer. The morphology and the structure of the layers were determined by Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HR-TEM), Energy Dispersive X-Ray Spectroscopy (EDXS), Auger and Infrared spectroscopy. SEM image of the WO₃-TiO₂ layer confirmed the nano-porosity of the layers and give the size of the particles of about 10 nm for TiO₂ and 30 nm for WO₃ layer. Further analysis indicated that the titanium sol penetrates the WO₃ layer. Particles in the WO₃ layer consist of a crystalline monoclinic WO₃ core surrounded by a 5–10 nm amorphous phase consisting of WO₃, TiO₂ and SiO₂. The WO₃-TiO₂ layers were used to assemble all solid state photoelectrochromic (PE) devices. Under 1 sun irradiation (1000 W/m²) the visible transmittance of the PE device changes from 62% to 1.6%. The colouring and bleaching processes last about 10 minutes.     

Evaluation of polymeric nanocomposites for the detection of toxic gas analytes

Four different metal oxide nanoparticles, copper oxide (CuO), aluminum oxide (Al₂O₃), nickel oxide (NiO), and titanium dioxide (TiO₂), were added to poly (2,5-dimethyl aniline) (P25DMA) during synthesis to create different polymer nanocomposites. These polymer nanocomposites were evaluated as potential sensing materials for six different gas analytes (acetaldehyde, acetone, benzene, ethanol, formaldehyde, and methanol). It was found that CuO did not incorporate into the P25DMA and only a small percentage of Al₂O₃ was incorporated. However, both NiO and TiO₂ were incorporated into the P25DMA at the same concentration as during the synthesis step. Overall, the type of metal oxide significantly affected the morphology of the sensing material and the amount of each analyte sorbed. For example, P25DMA doped with 5 wt% Al₂O₃ had high selectivity towards ethanol, whereas P25DMA doped with 20 wt% TiO₂ sorbed the most ethanol. However, P25DMA doped with 20 wt% TiO₂ also sorbed a high amount of formaldehyde, making P25DMA doped with 20 wt% TiO₂ less selective than P25DMA doped with 5 wt% Al₂O₃ towards ethanol with respect to formaldehyde.     

浸渍-分解法制备高可见光催化活性的Bi2O3/TiO2纳米管阵列

用浸渍-分解法将Bi₂O₃纳米颗粒沉积在TiO₂纳米管壁上, 制备了Bi₂O₃/TiO₂纳米管阵列. 用电感耦合等离子体发射光谱(ICP-AES)测定了Bi₂O₃/TiO₂ 纳米管阵列的化学组分, 利用X 射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外-可见(UV-Vis)吸收光谱表征了所制备的样品. 通过在可见光下(λ>400 nm)降解甲基橙(MO)水溶液来评价样品的光催化活性. 结果表明, Bi₂O₃纳米颗粒均匀地沉积在TiO₂纳米管中. Bi₂O₃/TiO₂纳米管阵列具有比纯Bi₂O₃膜和N-TiO₂纳米管阵列高得多的可见光催化活性. Bi₂O₃/TiO₂纳米管阵列活性的增强是其强可见光吸收和Bi₂O₃与TiO₂之间形成的异质结的协同作用的结果.     

CNTs表面改性与TiO2-CNTs异质结光催化性能

碳纳米管(CNTs)混酸(H₂SO₄/HNO₃, 体积比为3:1)超声辅助纯化及氧化植入活性基团－COOH, 进一步借助其转化为酰氯基团, 分别于CNTs 表面共价嫁接亲水性赖氨酸及亲脂性正十八胺基团, 赋予赖氨酸表面改性CNTs 显著水溶(6.85 mg·mL-1)和十八胺表面改性CNTs 显著醇溶(10.15 mg·mL^-1)性能. 运用低温水热法以亲水性CNTs 复合TiO₂, 溶胶-凝胶法以亲脂性CNTs 复合TiO₂, 观察到复合催化剂光催化性能随CNTs 溶剂分散性能增加而明显提升. 运用傅里叶变换红外(FTIR)、激光拉曼、X射线衍射(XRD)、Brunauer-Emmett-Teller 低温氮气吸附、透射电镜(TEM)及X光电子能谱(XPS)等手段表征, 系统探讨CNTs 的表面改性机制及CNTs 溶解分散性能与复合催化剂的光活性的关联. 认为表面改性CNTs 借助Ti－O－C键合促进其与纳米TiO₂的异质结合, 从而充分利用CNTs的大比表面积及电荷传输性能促进催化剂的污染物光催化降解.     

Synthesis and Characterization of an α-Fe2O3-Decorated g-C3N4 Heterostructure for the Photocatalytic Removal of MO

This study describes the preparation of graphitic carbon nitride (g-C₃N₄), hematite (α-Fe₂O₃), and their g-C₃N₄/α-Fe₂O₃ heterostructure for the photocatalytic removal of methyl orange (MO) under visible light illumination. The facile hydrothermal approach was utilized for the preparation of the nanomaterials. Powder X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive X-ray (EDX), and Brunauer–Emmett–Teller (BET) were carried out to study the physiochemical and optoelectronic properties of all the synthesized photocatalysts. Based on the X-ray photoelectron spectroscopy (XPS) and UV-visible diffuse reflectance (DRS) results, an energy level diagram vs. SHE was established. The acquired results indicated that the nanocomposite exhibited a type-II heterojunction and degraded the MO dye by 97%. The degradation ability of the nanocomposite was higher than that of pristine g-C₃N₄ (41%) and α-Fe₂O₃ (30%) photocatalysts under 300 min of light irradiation. The formation of a type-II heterostructure with desirable band alignment and band edge positions for efficient interfacial charge carrier separation along with a larger specific surface area was collectively responsible for the higher photocatalytic efficiency of the g-C₃N₄/α-Fe₂O₃ nanocomposite. The mechanism of the nanocomposite was also studied through results obtained from UV-vis and XPS analyses. A reactive species trapping experiment confirmed the involvement of the superoxide radical anion (O₂^•−) as the key reactive oxygen species for MO removal. The degradation kinetics were also monitored, and the reaction was observed to be pseudo-first order. Moreover, the sustainability of the photocatalyst was also investigated.     

脉冲沉积制备Cu2O/TiO2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO₂纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu₂O纳米颗粒修饰改性TiO₂纳米管阵列,形成Cu₂O/TiO₂ 纳米管异质结复合材料. 利用场发射扫描电镜（FESEM）、场发射透射电镜（FETEM）、X射线衍射（XRD）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）对样品进行表征,重点研究了Cu₂O/TiO₂ 纳米管异质结的光电化学特性和对甲基橙（MO）的可见光催化降解性能. 结果表明,Cu₂O纳米颗粒均匀附着在TiO₂纳米管阵列的管口和中部位置,所制备的Cu₂O/TiO₂ 纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol·L^-1的CuSO₄溶液中制得的Cu₂O/TiO₂纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu₂O纳米颗粒影响光催化活性的机理进行了讨论.     

Hierarchically Structure SnO2/ZnO Nanocomposites: Preparation,Growth Mechanism and Gas Sensing Property

SnO₂/ZnO nanocomposite was synthesized from mixed ethanol and water systems and the ethanol-sensing properties of sensors based on SnO₂/ZnO were investigated. The structure and morphology of the products was characterized by x-ray diffraction (XRD) and a field emission scanning electron microscope (FE-SEM). The results showed that the diameter of the liked pine needle SnO₂ was about 40 nm with a length about 300 nm, which are uniformly dispersed on the surface of the ZnO nanosheets. The growth process of the SnO₂/ZnO nanocomposite was discussed. The results of gas sensing properties of SnO₂/ZnO nanocomposite sensor showed high and quick response to ethanol vapor at 5.0 v. This sensor showed the advantages of high selectivity, strong stability, and prompt response/recovery characteristics in detecting ethanol vapor at 5.0 v.     

三维有序大孔复合材料Bi2O3/TiO2制备与多模式下光催化降解结晶紫

以TiO2为基体,在聚苯乙烯(PS)胶球和EO20PO70EO20(P123)两种模板剂作用下通过溶胶-凝胶及煅烧后处理方法制备了三维有序大孔纳米复合材料Bi2O3/TiO2.经傅里叶变换红外(FT-IR)光谱、X-射线衍射(XRD)、等离子体原子发射光谱(ICP-AES)、紫外-可见漫反射吸收光谱(UV-Vis DRS)、X-射线光电子能谱(XPS)、扫描电子显微镜(SEM)和N2吸附-脱附等物理测试手段对其组成、结构、形貌及表面物理化学性能进行了表征.结果表明,该复合材料晶型结构良好,孔结构排列整齐有序,孔壁呈介孔结构,属于三维有序大孔材料(3DOM).与TiO2相比,3DOM-Bi2O3/TiO2对光的吸收至少红移60 nm,且红移至可见区.在紫外光、可见光以及微波辅助等多模式光催化降解结晶紫的实验中,复合材料3DOM-Bi2O3/TiO2表现出良好的光催化活性,其活性明显高于P25、Bi2O3和Bi2O3/TiO2.同时,该复合材料针对不同类型的染料均表现出较好的紫外光降解效果,且3次循环实验后,依旧保持较高活性.     

Ag/Bi2WO6复合材料的制备及光催化性能

采用一步水热合成法制得花球状Bi_2WO_6和Ag/Bi_2WO_6光催化剂,借助X射线衍射(XRD)、场发射扫描电子显微镜(FES-EM)、透射电子显微镜(TEM)、X射线光电子能谱分析(XPS)、紫外-可见分光光度法(UV-Vis)等手段对样品进行结构性能表征。模拟日光的条件下,以甲基橙(MO)为降解物,对Bi_2WO_6和Ag/Bi_2WO_6的催化活性和机理进行研究。结果表明,相对Bi_2WO_6,相同条件下Ag/Bi_2WO_6对MO具有更佳的降解效果,当Ag掺杂量为1%(n/n)时,其降解率(180 min)可达到91.4%,同时一次回收样降解率也达到81%。此外,也对Ag/Bi_2WO_6复合材料的降解机理做了初步探究。     

Self-assembly of TiO2/polypyrrole nanocomposite ultrathin films and application for an NH3 gas sensor

TiO₂/polypyrrole (PPy) nanocomposite ultrathin films for NH₃ gas detection were fabricated by the in situ self-assembly technique. The films were characterized by UV–Vis absorption, FT–IR spectroscopy, and atomic force microscopy (AFM). The electrical properties of TiO₂/PPy ultrathin film NH₃ gas sensors, such as sensitivity, selectivity, reproducibility, and stability were investigated at room temperature in air as well as in N₂. The results showed that the optimum gas-sensing characteristics of TiO₂/PPy ultrathin film were obtained in the presence of 0.1?wt% colloidal TiO₂ for 20-min deposition. Compared with pure PPy thin-film sensors, the TiO₂/PPy film gas sensor has a shorter response/recovery time. It was also found that both humidity and temperature had an effect on the operation of the TiO₂/PPy film gas sensor at low NH₃ concentrations.     

Visible light degradation of ibuprofen using PANI coated WO3@TiO2 photocatalyst

A PANI-coated heterojunction of WO₃@TiO₂ nanocomposite was fabricated in three stages. The performance evaluation of the prepared photocatalyst for the degradation of ibuprofen was performed under visible light. Characterization of the photocatalyst using X-ray diffraction (XRD) analysis showed that the TiO₂ prepared constituted of the anatase phase. Furthermore, results from in situ XRD analysis of WO₃ show that it consisted of monoclinic and orthorhombic crystalline structures. These phases were not affected by the incorporation of PANI as revealed by XRD analysis. Results from Transmission electron microscopy (TEM) examination showed that sphere-like WO₃ and TiO₂ nanorods of different sizes were prepared In addition, fabrication of a heterojunction of WO₃@TiO₂ wrapped in PANI was shown by TEM analysis. Results from photoluminescence studies indicate that coupling TiO₂ with WO₃ enhanced the charge separation and the degradation performance of the nanocomposite. Supporting the heterojunction on PANI enhanced the degradation efficiency as indicated during the performance evaluation process. Diffuse reflectance spectra (DRS) calculations of the PANI/WO₃@TiO₂ catalysts showed that they can be used under visible light. The experimental results of X-ray Photon Spectroscopy (XPS) analysis showed the presence of elements W, C, O, Ti, and N. Solution pH influenced the degradation process and the maximum degradation efficiency was attained at pH 9. The degradation followed the Langmuir-Hinshelwood kinetic model with a Kinetic constant of 3.5 × 10^?2. The rate of degradation increased in the presence of bicarbonate/carbonate ions and persulfate ions.     

Bi2WO6 photocatalytic films fabricated by layer-by-layer technique from Bi2WO6 nanoplates and its spectral selectivity

Bi₂WO₆ multilayer films have been fabricated successfully by a layer-by-layer (LbL) technique from Bi₂WO₆ nanoplates, which show higher visible-light photoactivity (λ>420 nm) than that of Bi₂WO₆ nanoplate powders and P25 TiO₂ films. The films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and UV-visible absorption spectroscopy. Photocatalytic activities of the films were evaluated by the rhodamine B (RhB) decomposition under UV and visible-light irradiation. Thickness and photoactivity of the film can be modified easily by changing the deposition cycles. Bi₂WO₆ films have the spectral selectivity of the photocatalytic degradation of RhB. Under the wavelength greater than 300 nm, the RhB molecules tend to be transformed to rhodamine over Bi₂WO₆ films selectively. However, in the case of shorter wavelength (λ=254 nm) light irradiation, the RhB molecules can be photodegraded completely.