Transfert du trichloréthylène en milieu poreux à partir d'un panache de vapeursMass transfer of trichloroethylene in a porous medium from a vapor plume

A large scale experiment has been carried out on an experimental facility to study the mass transfer of trichloroethylene (TCE) in a partially saturated porous medium. 5 liters of TCE have been infiltrated in the vadose zone of the site. The mass transfer of TCE from the vapor plume in the unsaturated zone towards the top of groundwater was quantified based on an analytical and a numerical approach. The mass of the pollutant measured at the exit of the model is well represented by the two mathematical approaches. It is found that the transfer of TCE towards the groundwater from the vapor plume is weak, which corresponds to 285 g of TCE, approximately 4% of the initial mass. To cite this article: H. Benremita, G. Schäfer, C. R. Mecanique 331 (2003).     

Structuration de la convection mixte en milieu poreux confiné latéralement et chauffé par le bas : effets d''inertiePattern formation of mixed convection in a porous medium confined laterally and heated from below: effect of inertia

We consider the onset of convection in a porous medium heated from below and subjected to a horizontal mean flow. The effect of porous inertia is studied, and the transverse aspect ratio a of the medium is taken into accout. We find that the dominant modes are longitudinal rolls (L.R) if a is an integer or transverse traveling rolls (T.R) if a is below a_c with a_c<1. When a is not an integer with a>a_c, the setting on patterns are oscillatory three-dimensional structures (3D) for a>1 or T.R for a_c<a<1 provided that the Reynolds number remains below a critical value Re_K^*. We show that these structures are replaced by L.R if Re_K>Re_K^*. To cite this article: A. Delache et al., C. R. Mecanique 330 (2002) 885–891.     

Vérification expérimentale de la relation de réciprocité d'Onsager pour l'électro-osmose et l'électro-filtration dans une argile naturelleExperimental verification of the Onsager's reciprocal relations for electro-osmosis and electro-filtration phenomena on a saturated clay

This Note is devoted to the experimental verification of the Onsager's reciprocal relations in the particular case of electro-osmosis and electro-filtration. A special set up has been designed to carry out the measurements of both the electro-osmotic permeability and the streaming potential. This has been performed by using a natural material i.e., saturated kaolinite. To cite this article: K. Beddiar et al., C. R. Mecanique 330 (2002) 893–898.     

Surgénérateurs ; l'état des matériaux aux hautes irradiations, hautes puissances locales et températures, leurs gradients et propriétés mécaniques adaptées aux contraintes qui en résultent

The motivations to realize nuclear breeder reactors are developed in the present context of a strong growth in electronuclear power stations in many countries, using mostly moderated and water cooled reactors.The past studies can be of a substantial profit in France and, to a lesser degree, in other countries of the EU. However, to use fully the 238 uranium isotope, the materials for these breeders must withstand much harder radiation than those for water reactors. The power densities and thermal gradients will also be much more intense. The mechanical stresses, both static and dynamic, will be large and will act on materials with altered mechanical properties. Fuel elements will have to be produced with materials already irradiated several times and therefore showing such alterations.A field of studies concerning materials and their mechanical behavior in new and severe conditions is sketched here, both in construction and working conditions, together with proposed necessary instrumentation and research orientations.     

Modèles discrets de structures tissées : Analyse de stabilité et de drapéDiscrete models of woven structures: stability and draping analysis

A discrete model of a woven fabric structure is established, whereby nodes endowed with a mass and a rotational rigidity are connected by rigid bars to form a two-dimensional truss. The set of four bars that delineate a quadrilateral area is further endowed with a torsion deformation mode. The kinematics of the truss reproduces the large rotations and displacements encountered for real tissues. The equilibrium shape of such a structure is obtained as the minimum of its total potential energy versus the whole set of kinematic translational and rotational variables, accounting for eventual kinematic constraints due to contact with a rigid surface by the Lagrange multipliers method. A stability analysis is conducted, and the potentiality of the model is illustrated by fabric draping simulations. To cite this article: B. Ben Boubaker et al., C. R. Mecanique 330 (2002) 871–877.     

Impact of a bead on a rotating wall

We study experimentally the impact of a plastic bead on a rotating wall made of steel (velocity Ω; radial position x₀). The results show that the restitution coefficient is directly function of the impact velocity x₀Ω and is invariant by changing frame reference. The influence of the height of release of the particle on its angular velocity after impact is also studied. We observe an increase of the angular velocity with height followed by a saturation. We propose an interpretation for this evolution considering that the particle may roll without sliding during all the impact. This physical feature is not always taken into account in existing models of impact between rigid bodies. To cite this article: F. Rioual et al., C. R. Mecanique 336 (2008).     

Homogénéisation de problèmes d''évolution dans une structure renforcée de fibresHomogenization of evolution problems in a fiber reinforced structure

We study the homogenization of evolution equations such as:

where the coefficient a is -periodic and takes very high values on a subset TΩ (fibered structure) of very small measure. We find a non-local effective equation deduced from a homogenized system of several equations. To cite this article: M. Bellieud, C. R. Mecanique 330 (2002) 843–848.     

On the existence of the low-frequency surface waves in a porous mediumSur l'existence des ondes de surface basse fréquence en milieux poreux

The existence and propagation of the surface waves at a vacuum/porous medium interface are investigated in the low frequency range. Two types of surface waves are shown to be possible: the generalized Rayleigh wave, which always exists, and the Stoneley wave, which exists for a limited range of wave numbers. Moreover, within the k-domain of existence the Stoneley wave cannot appear for certain values of elastic parameters of the solid phase. The bifurcation behavior of both the Stoneley wave and the Biot (P2) bulk wave, depending on the wave number, is revealed. The asymptotic formulas for the phase velocities of the surface waves are derived. To cite this article: I. Edelman, C. R. Mecanique 332 (2004).     

A new formulation of immiscible compressible two-phase flow in porous media

A new formulation is proposed to describe immiscible compressible two-phase flow in porous media. The main feature of this formulation is the introduction of a global pressure. The resulting equations are written in a fractional flow formulation and lead to a coupled system which consists of a nonlinear parabolic (the global pressure equation) and a nonlinear diffusion–convection one (the saturation equation) which can be efficiently solved numerically. To cite this article: B. Amaziane, M. Jurak, C. R. Mecanique 336 (2008).     

Influence de la température sur la courbe de rétention d'eau de milieux poreuxInfluence of temperature on the water retention curve of porous media

This paper concerns the influence of temperature on the water retention curve of porous media. We present a model based on the differential of suction as a function of temperature, water content and void ratio. When adjusted for a given temperature, this model is able to predict the curve for any temperature. The model was validated by several tests on a ceramic (terra cotta) and a clayey silty sand at 20 and 60?°C. The application of the model to data found in the literature confirms its predictive power for a wide range of porous materials. To cite this article: S. Salager et al., C. R. Mecanique 334 (2006).     

Limit analysis and conic programming: ‘porous Drucker–Prager’ material and Gurson's modelAnalyse limite et optimisation conique : étude d'un matériau de Drucker–Prager poreux

Extending a previous work on the Gurson model for a ‘porous von Mises’ material, the present study first focuses on the yield criterion of a ‘porous Drucker–Prager’ material with spherical cavities. On the basis of the Gurson micro-macro model and a second order conic programming (socp) formulation, calculated inner and outer approaches to the criterion are very close, providing a reliable estimate of the yield criterion. Comparison with an analytical criterion recently proposed by Barthélémy and Dormieux—from a nonlinear homogenization method—shows both excellent agreement when considering tensile average boundary conditions and substantial improvement under compressive conditions. Then the results of an analogous study in the case of cylindrical cavities in plane strain are presented. It is worth noting that obtaining these results was made possible by using mosek, a recent commercial socp code, whose impressive efficiency was already seen in our previous works. To cite this article: M. Trillat et al., C. R. Mecanique 334 (2006).     

Elastic properties of glasses: a multiscale approach

Very different materials are named ‘Glass’, with Young's modulus E and Poisson's ratio ν extending from 5 to 180 GPa and from 0.1 to 0.4, respectively, in the case of bulk inorganic glasses. Glasses have in common the lack of long range order in the atomic organization. Beside the essential role of elastic properties for materials selection in mechanical design, we show in this analysis that macroscopical elastic characteristics (E,ν) provide an interesting way to get insight into the short- and medium-range orders existing in glasses. In particular, ν, the packing density (C_g) and the glass network dimensionality appear to be strongly correlated. Networks consisting primarily of chains and layers units (chalcogenides, low Si-content silicate glasses) correspond to ν>0.25 and C_g>0.56, with maximum values observed for metallic glasses (ν0.4 and C_g>0.7). On the contrary, ν<0.25 is associated to a highly cross-linked network with a tri-dimensional organization resulting in a low packing density. Moreover, the temperature dependence of the elastic moduli brings a new light on the ‘fragility’ of glasses (as introduced by Angell) and on the level of cooperativity of atomic movements at the source of the deformation process. To cite this article: T. Rouxel, C. R. Mecanique 334 (2006).     

Modelling of pH-dependent electro-osmotic flowsModélisation des variations de flux électro-osmotiques avec le pH.

NaCl-water saturated kaolinite is observed to show pH-dependent electro-osmotic flow. This behaviour is modelled by computing the electro-osmotic flow between parallel planes as a function of their electrical surface charge density. The latter can be related to pH through the physico-chemical properties of the material. In case of kaolinite particles, isomorphic substitution and two surface dissociation reactions allow to predict the pH-dependence of the electrical charge density and thus the variations of electro-osmotic flows with pH. To cite this article: P. Dangla et al., C. R. Mecanique 332 (2004).     

Comportement macroscopique des matériaux poreux à microstructure en feuilletsMacroscopic behavior of porous materials with lamellar microstructure

The solid phase of the porous material considered in this Note is made up of lamellar particles. The influence of interaction forces between platelets on the macroscopic behavior is addressed. The results provide a micromechanical basis to the modelling of the behavior of clays of the smectite group, for which repulsive forces arise from the electrical interaction between the solid platelets and the interstitial fluid. To cite this article: L. Dormieux et al., C. R. Mecanique 334 (2006).     

Espaces d'écoulements dits « universels », 3

Universal motions with uniform steady vorticity form a corolla of linear spaces derived from rigid body motions. Closely related to potential flows, they satisfy two extensions of Lagrange theorem, are investigated with the help of complex functions, as stand celebrated when be plane. They take place in hydrodynamics, aerodynamics, geophysics, astrophysics, turbulence, physics of plasmas and superfluid helium. In all the cases, arbitrary unsteady span-wise translations permit to generalise as well as to exhibit helical or 3D universal motions. Three misunderstood periodic flows illustrate our purpose, as they approach shear instabilities in numerous fluids. To cite this article: M. Bouthier, C. R. Mecanique 332 (2004).     

Nonlinear behavior of matrix-inclusion composites under high confining pressure: application to concrete and mortar

This paper is devoted to a micromechanics-based simulation of the response of concrete to hydrostatic and oedometric compressions. Concrete is described as a composite made up of a cement matrix in which rigid inclusions are embedded. The focus is put on the role of the interface between matrix and inclusion which represent the interfacial transition zone (ITZ). A plastic behavior is considered for both the matrix and the interfaces. The effective response of the composite is derived from the modified secant method adapted to the situation of imperfect interfaces. To cite this article: T.H. Le et al., C. R. Mecanique 336 (2008).     

Variance of the virtual displacement

We show that the affine structure of the 3-dimensional space is deeply enmeshed with the static laws expression. The relevance of tensorial rules for calculus in mechanics is thus enhanced. The virtual work principle is stated precisely but a little twist is given to the usual statements: the tensorial nature of the so-called virtual displacement vector is asserted to be covariant. To cite this article: C. Vallée et al., C. R. Mecanique 332 (2004).

Résumé

Nous montrons que la structure affine de l'espace tridimensionnel est fortement imbriquée avec l'expression des lois de la statique. La pertinence de l'application des règles du calcul tensoriel à la mécanique est ainsi renforcée. Le principe des travaux virtuels est établi précisément avec une seule entorse aux exposés classiques : la nature tensorielle de l'habituel vecteur déplacement virtuel est affirmée covariante. Pour citer cet article : C. Vallée et al., C. R. Mecanique 332 (2004).     

Évaluation de l'influence des changements de géométrie sur les déformations de séchage d'un milieu poreux fissuréInfluence of geometry changes on drying-induced strains in a cracked solid

The macroscopic response of a cracked solid subjected to drying is investigated within the framework of micromechanics. The originality of this contribution lies in the fact that the variations of the aspect ratios of cracks induced by the capillary pressure increase are accounted for. When the initial aspect ratio is small enough, it is shown that neglecting the geometrical changes yields an erroneous prediction of the sign of the macroscopic volume strain rate. To cite this article: X. Chateau et al., C. R. Mecanique 331 (2003).