Absolute strain measurements made with fiber bragg grating sensors

A strain sensor system based on optical fiber Bragg gratings (FBGs) is proposed with a new matched-filter design. The strain variation on the sensor FBG is continuously followed and matched by a filter FBG by use of a feedback control loop that produces an identical strain condition on the filter FBG. The matched strain on the filter FBG is then determined from the resonance vibration of the fiber piece embedding the filter FBG. The implementation and the performance of the proposed system are described. It is demonstrated that the proposed system can distinguish strain variation on the sensor FBG with resolution of one microstrain.     

Switchable dual-wavelength single-longitudinal-mode erbium-doped fiber laser using an inverse-Gaussian apodized fiber Bragg grating filter and a low-gain semiconductor optical amplifier

We present a stable and switchable dual-wavelength erbium-doped fiber laser. In the ring cavity, an inverse-Gaussian apodized fiber Bragg grating serves as an ultranarrow dual-wavelength passband filter, a semiconductor optical amplifier biased in the low-gain regime reduces the gain competition of the two wavelengths, and a feedback fiber loop acts as a mode filter to guarantee a stable single-longitudinal-mode operation. Two lasing lines with a wavelength separation of approximately 0.1 nm are obtained experimentally. A microwave signal at 12.51 GHz is demonstrated by beating the dual wavelengths at a photodetector.     

Multifrequency erbium-doped fiber laser operating at room temperature

A method to realize room-temperature operation of a multifrequency Er-doped fiber laser with low-frequency shift feedback placed within a linear laser cavity is theoretically proposed and experimentally demonstrated. Simultaneous multiwavelength lasing with 0.5 nm wavelength spacing is experimentally demonstrated by applying a sinusoidal signal of 10 kHz to a fiber phase modulator inserted within the linear cavity to prevent single wavelength steady-state oscillation. In the linear cavity, an all-polarization-maintaining fiber Sagnac loop is used as a periodic filter, and a single-mode fiber loop with a polarization controller is used as a partial reflector and also as an output port.     

Temperature compensated fiber Bragg grating using fiber reinforced polymeric composites

Abstract

The thermal drift coefficient of the Bragg wavelength of fiber Bragg grating (FBG) is unacceptably high when the FBG is used as a wavelength reference or a wavelength‐selective passive component, especially in a dense wavelength division multiplexing (DWDM) system. A light, small and robust carbon fiber reinforced polymeric composite structure is proposed to compensate for the temperature induced wavelength drift in FBG. It has been shown to be able to reduce the temperature induced wavelength shift of a fiber Bragg grating from 10 pm/°C to below 1 pm/°C. Stability in long term performance over a two month period has also been demonstrated. A fabrication route that leads to optimal compensation performance has also been proposed.     

Transparent network for hybrid multiplexing of fiber Bragg gratings and intensity-modulated fiber-optic sensors

A network for multiplexing fiber Bragg gratings (FBGs) and intensity-modulated fiber-optic sensors with no need to distinguish between the two kinds of sensor is proposed and experimentally demonstrated. Two FBG sensors and two intensity-modulated sensors are wavelength-division multiplexed; the electrical phase of the output signal is measured as a common parameter for both types of sensor. Furthermore, the intensity sensors become power referenced, and the FBG sensors are interrogated by a low-cost technique. Low cross talk is achieved by use of a tunable optical filter at the detector.     

Wavelength switching of picosecond pulses generated from a self-seeded Fabry-Perot laser diode with a tilted fiber Bragg grating formed in a graded-index multimode fiber

We demonstrated the generation of wavelength-switchable picosecond pulses from a self-seeded Fabry-Perot laser diode that used a tilted fiber Bragg grating (FBG) formed in a graded-index multimode fiber as an external optical feedback element, where wavelength switching was achieved by controlling the modal distribution in the FBG. We measured the reflection spectra of multimode FBGs fabricated with different tilt angles and discussed the effects of the tilt angle on wavelength selection. By using a 20?mm long 1.65° tilted FBG and a fiber deformer to control the modal distribution in the FBG, we generated 2?GHz pulses with a wavelength switchable over 14 wavelengths at a spacing of ～0.8?nm.     

Analysis of optical switching in a Yb3+-doped fiber Bragg grating by using self-phase modulation and cross-phase modulation

The optical performances of the all-optical switching based on Yb3+-doped fiber Bragg grating (FBG) are investigated under the case of self-phase modulation (SPM) and cross-phase modulation (XPM). For the SPM case, the optical bistability of FBG under different parameters is investigated. It shows that the width of the hysteresis loop and threshold switching power are strongly dependent on the fiber grating length, fiber grating detuning, and coupling constant. For the XPM case, the expressions of the threshold switching power in the different detuning range are given. The influence of parameters about different detuning and coupling constant to the threshold switching power and extinction ratio are also studied. In comparison with the SPM case, the switching power of FBG under XPM case can be reduced to less than 20 mW by optimizing the parameters of FBG.     

纤维复合材料层合板内埋光纤光栅传感器的保护技术

内埋的光纤Bragg光栅（FBG）传感器的存活率及测试精度是其在线监测纤维增强树脂基复合材料制备和服役状态的重要前提。采用[90₁₁/0₁₁]的碳纤维预浸料铺层方式,在层合板0°和45°方向的典型位置埋入FBG温度和应变传感器,采用模压成型工艺制备复合材料层合板。在异向铺排（光纤光栅方向与碳纤维方向不同）的45°方向光纤光栅传感器内埋于碳纤维预浸料层间的过程中,对其采用4种不同的保护方式。通过对比实验结果发现:当对异向铺排的FBG传感器不采取保护措施时,在加热加压复合材料时光纤光栅容易失活;整层铺设同向预浸料以保护异向铺排的FBG传感器的方式改变了具有特定铺层参数复合材料的力学性能;采用窄长条同向预浸料上下包埋保护FBG传感器的方式增大了应变光栅测量结果的系统误差;采用窄长条同向预浸料上下包埋并在邻近铺层开凹槽的保护方式能明显提高内埋光纤光栅的存活率及测试精度。      

Estimations of fiber Bragg grating parameters and strain gauge factor using optical spectrum and strain distribution information

An inverse approach based on an optimization technique is proposed to characterize a fiber Bragg grating (FBG) and the strain gauge factor (GF) when the FBG is bonded on a structure. By bonding an FBG on a substrate and simply straining this FBG into a chirped fiber Bragg grating with a predesignated strain, the proposed method, based on an optimization technique, can be used to reconstruct seven parameters of the FBG from the corresponding reflective spectrum. The parameters identified are the length of an FBG, the grating period, the average refractive index, the index modulation, the apodization coefficient, the starting point bonded on the plate, and the strain GF. The information from the predesignated strain, as well as the measured reflective spectrum, is used as the objective function during the optimal search. As a result, the design sensitivity for the optimal search is much improved compared with the design sensitivity when only the reflective spectrum is used. In particular, the strain GF, which depends on the adhesive, the bonding layer characteristics, etc., can be determined in order to provide a reference for an FBG used as a strain sensor. Results from numerical simulations and experiments show that seven parameters of an FBG can be obtained accurately and efficiently.     

Optimization algorithm for ultrabroadband multichannel aperiodic fiber Bragg grating filters

We consider an approach to designing complex multichannel filters for ultrabroadband applications. In contrast to earlier approaches that are restricted to specific problems, our generalized method can be applied to any conceivable fiber Bragg grating (FBG) multichannel design. Our method accommodates hundreds of filter channels that are spaced unevenly in wavelength, with variable widths, depths, and shapes. We demonstrate the power of the method for an FBG design with 150 narrow channels over the region 1400-1800 nm.     

Fiber-Bragg-grating force sensor based on a wavelength-switching actively mode-locked erbium-doped fiber laser

A fiber-Bragg-grating (FBG) transverse-force sensor based on a wavelength-switching actively mode-locked erbium-doped fiber laser is proposed, in which a FBG is used as both the sensing element and the wavelength-selection element of the laser. When a force is applied to the FBG, the induced birefringence in the FBG causes the laser to emit pulses at two close wavelengths, whose separation is proportional to the applied force. To suppress the interference between the two wavelengths, the laser is made to emit at the two wavelengths alternately by use of a polarization-switching technique. The wavelength separation is converted into a time difference by transmission of the laser pulses through a dispersive single-mode fiber, so the wavelength measurement is replaced by the less-expensive time measurement. The output of the sensor is insensitive to temperature and axial strain changes along the FBG. To interrogate similar FBG sensing elements connected in series it is necessary only to change the modulating frequency of an electro-optic modulator to select the corresponding laser cavity. The practicability of this approach was demonstrated experimentally with two multiplexed sensing elements.     

Fiber Bragg grating sensor interrogation using chirped fiber grating-based Sagnac loop

We have investigated numerically and experimentally a fiber Bragg grating (FBG) sensor interrogation scheme utilizing a linear chirped grating-based Sagnac loop as a wavelength-dependent receiver. The scheme is suitable for both static and dynamic sensor interrogation with advantages of stable and linear readout response and easily-adjustable sensing resolution and dynamic range. Static and dynamic strain resolutions as high as /spl plusmn/ 4.2 /spl mu//spl epsiv/ and 0.406 /spl mu//spl epsiv///spl radic/ Hz have been demonstrated using this scheme.     

Optical bandpass filter from a curved segment of a detuned two-core fiber

We present the use of a dual-core fiber as a bandpass filter. Our device is based on the fact that intrinsic detuning between the propagation constants of the two cores can be compensated for in a controlled manner by use of a loop. This compensation is made to occur for a specific frequency band, so that the resulting device acts as a bandpass filter.     

光纤饱和吸收体稳频窄线宽光纤激光器

结合光纤饱和吸收体与光纤光栅法布里-珀罗标准具,研制出了全光纤结构1550nm单频窄线宽掺铒光纤环形激光器.采用两个976nm激光二极管双向抽运作为抽运源,高掺杂浓度铒光纤作为增益介质,以行波腔消除空间烧孔效应,利用光纤光栅法布里-珀罗标准具窄带选模特性,以10m长低掺铒光纤饱和吸收体稳频,得到了十分稳定的窄线宽激光输出.激光器抽运阈值功率21mW,在抽运光功率为145mW时输出光功率39mW,斜率效率30%,信噪比大于50dB.采用延迟自外差方法精确测量光纤激光器线宽小于10kHz.     

Switchable and tunable multiple-channel erbium-doped fiber laser using graphene-polymer nanocomposite and asymmetric two-stage fiber Sagnac loop filter

A high-performance multiple-channel erbium-doped fiber laser (EDFL) is proposed and experimentally demonstrated, using graphene-polymer nanocomposite as a multiwavelength equalizer and an asymmetric two-stage polarization-maintaining fiber (PMF) Sagnac loop as a flexible comb filter. At first, the filtering characteristics of the PMF Sagnac loop filter (SLF) are investigated. Both theoretical and experimental results show that it can provide a flexibly switchable and tunable comblike filtering. Then, the two-stage PMF SLF is inserted into a graphene-assisted EDFL cavity for generating multiwavelength oscillation. The extreme-high third-order optical nonlinearity of graphene is exploited to suppress the mode competition of the EDFL, and a stable multiple-channel lasing is observed. By carefully adjusting the polarization controllers in the two-stage PMF SLF, not only can the lasing-line number per channel be switchable between single and multiple wavelengths, but also the wavelength spacing in the triple-wavelength condition can be tunable. In the case of triple wavelengths per channel, up to 12 wavelengths with four channels stable oscillations can be achieved. The multiple-channel EDFL can keep a high extinction ratio of >40 dB and a narrow linewidth of <0.01 nm.     

Performance analysis of a fiber Bragg grating filter-based strain/temperature sensing system based on a modified Gaussian function approximation method

This paper analyzes the performance of a fiber Bragg grating (FBG) filter-based strain and/or temperature sensing system based on a modified Gaussian function (MGF) approximation method. Instead of using a conventional Gaussian function, we propose the MGF, which can capture the characteristics of the sidelobes of the reflected spectrum, to model the FBG sensor and filter. We experimentally demonstrate that, by considering the contributions of the sidelobes with the MGF approximation method, behaviors of the FBG filter-based FBG displacement and/or temperature sensing system can be predicted more accurately. The predicted behaviors include the saturation, the sensitivity, the sensing range, and the optimal initial Bragg wavelengths of the FBG sensing system.     

High-strength fiber Bragg gratings for a temperature-sensing array

We have successfully demonstrated a one-step laser process of fabricating fiber Bragg grating arrays directly through fiber buffer. A new polysiloxane-based buffer provides high 244-nm transmission and showed no degradation due to UV irradiation or thermal annealing as verified by Weibull analysis of tension tests. The FBG array can withstand over 400-kpsi tension tests and 220/spl deg/C temperature. The spectral quality of the FBG is compatible with the FBGs currently used by the sensing industry and, therefore, can be interrogated with existing instruments. The laser fabrication process is robust with no coating, stripping, or recoating required.     

人体测温光纤光栅温度传感器的研制

针对医疗行业对人体测温的需要,研制了一种以裸光纤Bragg光栅为传感元件的光纤光栅温度传感器,并对其温度特性进行了研究.采用恒温水浴对工作波长为1 557 nm和1 547 nm附近的2只光纤光栅传感器进行温度定标.结果表明,在34～48℃范围内,光纤光栅的中心波长随温度的变化呈现良好的线性关系,相关系数分别为0.998 3和0.997 4,光纤光栅温度传感器的测温标准偏差分别为0.239℃和0.245℃,可应用于医疗中人体温度的实时监测.     

Tunable multiwavelength fiber laser based on a double Sagnac HiBi fiber loop

A tunable multiwavelength fiber laser based on double Sagnac loops is proposed and demonstrated. Comb filter characteristics of single and double Sagnac loops are analyzed by Jones matrix. Simulated results show that there are better tunability and controllability with double loops than with a single loop, and this also has been confirmed by experimental results. By adjusting the polarization controller and the length of the polarization maintaining fiber the wavelength range, wavelength spacing, and laser linewidth can be tuned. Experimental results indicate that the linewidth of the multiwavelength fiber laser was 0.0187 nm and the optical sidemode suppression ratio was 50 dB.     

Analysis of polarization properties of a mode-locked fiber laser gyroscope

We investigated the polarization characteristics of a mode-locked fiber laser gyroscope (MLPLG) formed with a Nd-doped fiber as an optical gain medium and a Sagnac loop mirror. The output pulse patterns and the polarization states were found to be determined by fiber birefringence in the different sections of the MLPLG. We describe the conditions for the MLPLG to operate with automatic reciprocity leading to the possibility of phase-error-free operation.