Ru-PAA复合纳米粒子与蛋白质相互作用的光谱研究及其应用

以过硫酸钾作为引发剂,丙烯酸为单体,在超声作用下原位聚合制备聚丙烯酸(PAA)修饰Ru纳米复合颗粒(Ru-PAA).修饰后的Ru-PAA复合纳米颗粒,不仅水溶性和稳定性得到改善,同时具有良好的生物相容性.研究了Ru-PAA复合纳米颗粒与蛋白质的相互作用,并利用散射光谱法考察了光散射强度与蛋白质浓度之间的关系.结果发现: 在最佳的实验条件下,BSA浓度为0.05～1.2 mg/L、HSA浓度为0.05～3 mg/L时,其浓度与光散射强度均有良好的线性关系,检出限均为0.01 mg/L.该方法用于实际样品测定,得到了令人满意的结果.     

新荧光增敏法测定人血清蛋白质

合成了新荧光试剂5-(4-羧基苯偶氮)-8-水杨醛缩氨基喹啉(p-CPSAQ),探讨了与人血清蛋白反应的最佳实验条件.在pH=7.0的缓冲体系中,蛋白质的存在使p-CPSAQ的荧光大大增强,据此建立了测定人血清蛋白质的灵敏方法;对人血清白蛋白和γ-球蛋白的线性范围分别为0.1～4.5 mg/L和 0.1～4.0 mg/L;检出限分别为0.028和0.027 mg/L.方法灵敏、快速、选择性好,用于人血清样品中总蛋白的测定,结果满意.     

蛋白质-四羧基铜酞菁体系的共振散射行为及其分析应用

在pH 3.0的Clark-Lub's 缓冲溶液中,蛋白质与四羧基铜酞菁(CuPc(COOH)4)作用,使体系的共振光散射增强,在λ=389 nm处光散射强度最大.增强作用的强弱与蛋白质的含量成正比,据此建立了共振光散射测定蛋白质的新方法.此方法对牛血清白蛋白(BSA)、人血清白蛋白(HSA)、免疫球蛋白G(IgG)、鱼精蛋白(Protamine)、血清总蛋白(TP)的测定范围分别为0.05～1.60 mg/L、 0.025～1.60 mg/L、 0～1.45 mg/L、 0.1～1.50 mg/L、 0～1.60 mg/L,相应检出限分别为1.12×10-2 mg/L、 1.11×10-2 mg/L、 1.95×10-2 mg/L、 3.61×10-3 mg/L、 4.34×10-3 mg/L.方法应用于实际人血清样品中总蛋白的测定,结果与考马斯亮蓝法基本一致.     

钍试剂Ⅱ与蛋白质作用的共振胱散射特征及微量蛋白质的光散射测定

研究了钍试剂Ⅱ与蛋白质在PH4．3条件下作用的共振光散射特征，并以此建立了测定微量蛋白质的新方法。用普通荧光分光光度计测量了这一体系的共振光散射光谱，考察了影响因素。在最佳实验条件下，牛血清白蛋白（BSA）浓度在0mg/L-10.0mg/L范围内成线性关系，方法已用于尿中微量蛋白质的测定。     

过氧化氢氧化法制备羧基化碳纳米管的研究

研究了在不同的酸碱性、反应时间和反应温度三个条件下,过氧化氢氧化单壁碳纳米管制备羧基化碳纳米管的效果,通过红外光谱表征和羧基化碳纳米管的酰胺化修饰反应,确定了羧基的引入.研究发现,单壁碳纳米管与过氧化氢、稀硫酸于105℃回流反应60 min条件下,制备羧基化碳纳米管的效果最为理想,且比文献报道的浓硫酸浓硝酸组成的混酸氧化效果更好.并对在该条件下制备羧基化碳纳米管效果较好的原因作了简单的分析探讨.     

多孔"类碳糊电极"的羧基化及其对Escherichia ocli O157:H7的检测

以吡咯为前驱体,羧基化碳纳米管、石墨粉为填料和碳酸钙微球为模板直接诱导合成,制备出一种高灵敏的多孔"类碳糊电极"生物电化学传感器,讨论了羧基化碳纳米管含量、银染时间对检测结果的影响.结果表明,最佳羧基化碳纳米管含量为8%,最佳银染时间为12 min,银的阳极溶出峰电流与E. ocli O157:H7浓度在1.0×104～1.0×106 cells/mL范围内呈线性关系,其线性回归方程为:IP=-5.582+1 972logC,相关系数(R2)为0.9912,检出限为5.1×103cells/mL,实现了对E. ocli O157:H7快速、准确地检测.     

梯度薄膜增敏的光波导表面散射传感方法用于生物气溶胶探测

生物气溶胶监测对于疾病防控、防化反恐、环境保护与资源调查等至关重要。本研究提出了一种基于高折射率梯度薄膜增敏的平板玻璃光波导表面散射传感方法,通过探测光波导散射光强度随时间的变化,分析生物气溶胶在光波导表面的颗粒沉降过程,进而获取生物气溶胶的浓度等信息。本研究通过理论推导得出光波导散射光强度与沉降粒子数之间的函数关系式,选用牛血清蛋白(BSA)水溶液作为生物气溶胶原液,采用五氧化二钽(Ta₂O₅)梯度薄膜增敏的离子交换平板玻璃单模光波导测试了BSA分子团聚体沉降引起的表面散射光变化,通过比对测试分析了Ta₂O₅梯度薄膜的增敏效果。实验结果表明,散射光强度随BSA分子团聚体沉降量的增加而增大,与BSA原液浓度呈良好线性关系,当单模玻璃光波导表面覆盖Ta₂O₅梯度薄膜后,其在横电基模(TE0)下对BSA分子团聚体沉降的探测灵敏度提高了50倍,并且采用TE0模测得的探测灵敏度比横磁基模(TM0)高4倍。本研究制备的Ta₂O₅     

碳纳米微粒的共振散射光谱研究

液相碳纳米微粒的共振散射光谱实验表明,当碳浓度小于360mg/L时,它在400、470、510和940nm产生4个共振散射峰;浓度大于900mg/L时无共振散射、碳微粒浓度在0．45－45mg/L范围内与共振散射光强度I470nm成良好的性关系,研究了光源和扫描速度对液相碳纳米微粒共振散射光谱的影响。结果表明,光源的发射强度分布不一是产生共振散射光谱峰的一个重要因素,并结合已有的实验结果提出了界面共振吸收和黑白纳米微粒共振散射概念,解释了碳纳米微粒体系的共振散射光谱。     

钍试剂Ⅱ与蛋白质作用的共振光散射特征及微量蛋白质的光散射测定

研究了钍试剂Ⅱ与蛋白质在pH 4 3条件下作用的共振光散射特征 ,并以此建立了测定微量蛋白质的新方法。用普通荧光分光光度计测量了这一体系的共振光散射光谱 ,考察了影响因素。在最佳实验条件下 ,牛血清白蛋白 (BSA)浓度在 0mg/L～ 1 0 0mg/L范围内成线性关系。方法已用于尿中微量蛋白质的测定     

用铬黑T作为共振光散射探针测定蛋白质

研究了金属指示剂铬黑T（EBT）作为共振光散射探针测定蛋白质的分析方法。实验表明，在pH=4.10的Britton-Robinson缓冲溶液条件下，铬黑T只有极弱的光散射，它与蛋白质结合后有强烈的共振光散射作用。在λ=375nm处，光散射强度最大，光散射强度与蛋白质的浓度成正比。据此建立了一种测定蛋白质的新方法。该方法简便、快速、灵敏度高，对HSA的检出限达到39μg/L;线性范围为0－15mg/L，用于人体血清样品的分析并用考马斯亮蓝法比较，取得了令人满意的结果。同时亦研究了牛血清白蛋白（BSA）、λ球蛋白、鸡蛋白蛋白、溶菌酶与染料EBT之间的作用。比较了2种不同类型的荧光仪器绘制的共振光散射光谱，并探讨了共振光散射的机理。     

Rapidly functionalized, water-dispersed carbon nanotubes at high concentration

Microwave-assisted functionalization of single-wall carbon nanotubes (SWNTs) in a mixture of nitric and sulfuric acids was carried out to synthesize highly water-dispersible nanotubes. Stable concentrations as high as 10 mg/mL were obtained in deionized water that are nearly 2 orders of magnitude higher than those previously reported. This was after only 3 min of functionalization reaction. Fourier transform infrared spectra showed the presence of carboxylated (-COOH) and acid sulfonated (-SO(2).OH or -SO(3)(-) H(+)) groups on the SWNTs. On the basis of elemental analysis, it was estimated that one out of three carbon atoms was carboxylated, while one out of 10 carbon atoms was sulfonated. The Raman spectra taken both in aqueous dispersion and in the solid phase indicated charge transfer from the SWNT backbone to the functional groups. Scanning electron microscope images of thin films deposited from an aqueous suspension showed that the SWNTs were aligned parallel to one another on the substrate. The images also indicated some reduction in average length of the nanotubes. Transmission electron microscope images of thin films from a dilute methanol dispersion showed that the SWNTs were extensively debundled. Laser light scattering particle size measurements did not show evidence for the existence of particles in the 3-800 nm size range, indicating that the functionalized SWNTs might have dispersed to have formed a true solution. Moreover, the microwave-processed SWNTs were found to contain significantly smaller amounts of the original iron catalyst relative to that present in the starting nanotubes. The electrical conductivity of a thermally annealed thin membrane obtained from the microwave-functionalized SWNTs was found to be the same as that of a similar membrane obtained from a suspension of the starting nanotubes.     

Bi(Ⅲ)-茜素红-CTMAB体系共振散射光谱法测定环境水样中痕量铋

在pH=4.1的HCl溶液中,Bi(Ⅲ)与茜素红和十六烷基三甲基溴化铵（CTMAB）缔合形成粒径较大的疏水性三元离子缔合物（结合比为n(Bi(Ⅲ))∶n(AR)∶n(CTMAB)=1∶3∶3）,该反应导致共振光散射显著增强,最大散射峰位于364 nm。 研究了反应介质、pH值、共振探针浓度等对散射体系的影响,考察了该散射反应的稳定性及共存物质的影响,并对该三元离子缔合物的反应机理进行了探讨。 在2.5 mL 1.0×10-4 mol/L茜素红和2.0 mL 1.0×10-4 mol/L CTMAB最优试验条件下,Bi(Ⅲ)质量浓度与共振光散射强度ΔI364 nm在0～0.384 mg/L范围内呈良好线性关系,检测限为5.898×10-8 g/L,对含量为0.18 mg/L Bi(Ⅲ)溶液进行11次平行测定,其相对标准偏差为2.2%。 将该方法用于环境水样中痕量铋(质量浓度为0.552～0.831 μg/L)的测定,加标回收率为99.5%～100.2%,测定偏差小于2.7%。 基于Bi(Ⅲ)-AR-CTMAB三元离子缔合物的共振光散射光谱,建立了以茜素红染料为光谱探针的痕量Bi(Ⅲ)共振光散射检测新方法。     

Bare gold nanoparticles mediated surface-enhanced Raman spectroscopic determination and quantification of carboxylated single-walled carbon nanotubes

The paper proposes a simple and portable approach for the surface enhanced Raman scattering (SERS) spectroscopy in situ determination of carboxylated single walled carbon nanotubes (SWNTs) in river water samples. The method is based on the subsequent microfiltration of a bare gold nanoparticles solution and the water sample containing soluble carbon nanotubes by using a home-made filtration device with a small filtration diameter. An acetate cellulose membrane with a pore size of 0.2 μm first traps gold nanoparticles to form the SERS-active substrate and then concentrates the carbon nanotubes. The measured SERS intensity data were closely fit with a Langmuir isotherm. A portable Raman spectrometer was employed to measure SERS spectra, which enables in situ determination of SWNTs in river waters. The limit of detection was 10 μg L⁻¹. The precision, for a 10 mg L⁻¹ concentration of carbon nanotubes, is 1.19% intra-membrane and 10.5% inter-membrane.     

Amphiphilic polymers facilitated solid-phase extraction coupled with ultra-performance liquid chromatography-tandem mass spectrometry for direct extraction and analysis of zearalenone and zearalanone in corn juice samples

In this work, amphiphilic polymers synthesized from carboxylated carbon nanotubes stabilized high internal phase emulsions are demonstrated to be capable of direct extracting zearalenone and zearalanone in samples consisting of an oil-water emulsion system. Under optimal conditions, the maximum adsorption capacities for zearalenone and zearalanone are 17.27 and 13.26 mg/g. The adsorption is mainly attributed to π-π interaction, hydrophobic interaction, and hydrogen-bonding interaction for zearalenone and zearalanone. The adsorption isotherms reveal that the adsorption of zearalenone and zearalanone on amphiphilic polymers synthesized from carboxylated carbon nanotubes stabilized high internal phase emulsions follows Freundlich model with multilayer and heterogeneous adsorption due to the presence of multiple kinds of adsorption sites. The relative recoveries of the spiked zearalenone and zearalanone in corn juice samples range from 85% to 93% with relative standard deviations lower than 3.52%. The results manifest the high efficiency of amphiphilic polymers synthesized from carboxylated carbon nanotubes stabilized high internal phase emulsions for the adsorption and separation of analytes in the oil-water emulsion system. This study provides a new perspective on adsorbent engineering for the adsorption application in heterogeneous media.     

Degradation of physicomechanical properties of epoxy nanocomposites with carbon nanotubes upon heat and humidity aging

The dependence of the physicomechanical properties of epoxy nanocomposites subjected to heat and humidity aging on the type of covalently functionalized carbon nanotubes and on the uniformity of their distribution in the epoxy matrix was studied. Two types of carbon nanotubes were used: those modified with carboxy and amide groups. The elastic modulus, bending deflection, and ultimate bending strength for the initial epoxy nanocomposites with carbon nanotubes and for those subjected to heat and humidity aging were determined. The epoxy binders modified with carboxylated carbon nanotubes are more resistant to the action of aging factors. The presence of aggregates of carboxylated carbon nanotubes in the epoxy matrix positively influences the preservation of physicomechanical properties of the composite subjected to heat and humidity aging. Microscopic examination revealed structural features of the epoxy nanocomposite and their effect on the resistance of the composite to the heat and humidity aging.     

二苯胺磺酸钠共振光散射法测定牛尿中白蛋白的研究

研究了以二苯胺磺酸钠为共振光散射探针测定牛尿中牛血清白蛋白的分析方法.该方法基于在pH=3.0的Britton-Robinson缓冲溶液中,牛血清白蛋白(BSA)与二苯胺磺酸钠结合后有强烈的共振光散射作用,在λ=469 nm处,共振光散射强度最大且光散射的强度与BSA的浓度成正比.方法简便、快速、灵敏度高,对BSA的检出限为0.18 mg/L,线性范围为0.20～16 mg/L,相关系数r=0.996.该法用于牛尿样品的分析测定,结果满意.     

纳米氧化铜-碳纳米管修饰玻碳电极同时检测邻、对苯二酚

以商品化纳米氧化铜和羧化碳纳米管作为玻碳电极修饰材料,结合了两种材料的放大电信号和电催化性能,所构建的复合物修饰电极可区分性质相近的同分异构体邻苯二酚和对苯二酚的信号,同时可进一步放大两种酚的峰电流。 因此该基于纳米氧化铜和碳纳米管的电化学传感器可用于邻苯二酚和对苯二酚的同时检测。 采用循环伏安法对复合物中两种材料的比例、修饰量以及支持电解质pH进行了优化:纳米氧化铜和碳纳米管质量比为5∶1,修饰量为9 μL,pH=7.4的磷酸盐缓冲溶液被用作电解质溶液。 在优化的条件下,邻苯二酚和对苯二酚的微分脉冲伏安扫描峰电流与浓度在6.0×10^-7~3.0×10^-3 mol/L范围内均呈良好的线性关系,检出限(S/N=3)分别为1.0×10^-7和1.6×10^-7 mol/L。 该方法具有成本低、操作简便、快速的特点,对实际水样的加标回收率在94.6%~101.1%范围内,具有较好的实际应用前景。     

光谱法研究埃洛石纳米管与溶菌酶间的相互作用

以溶菌酶作为模型蛋白,主要利用光谱法研究了埃洛石纳米管与溶菌酶之间的相互作用。荧光光谱结果表明向溶菌酶体系中加入埃洛石纳米管会出现荧光猝灭现象,猝灭机理符合静态猝灭规律。共振光散射强度的增加可能与埃洛石纳米管-溶菌酶复合物的形成而导致的分子尺寸的增加有关,这与紫外-可见吸收光谱的变化和静态猝灭机理相一致。同步荧光光谱分析表明两者之间的相互作用可能发生在色氨酸所处位置附近,作用过程使溶菌酶的二级结构发生变化,分子链错误折叠,加入浓度为100mg/L和200mg/L的埃洛石纳米管时,通过圆二色谱数据计算出分别导致α-螺旋的含量降低3.28%和6.89%。     

Determination of non-steroidal anti-inflammatory drugs in urine by combining an immobilized carboxylated carbon nanotubes minicolumn for solid-phase extraction with capillary electrophoresis-mass spectrometry

Last years, the usefulness of the use of carbon nanotubes (CNTs) as sorbent material have been demonstrated for a wide variety of compounds. In this work, it has been demonstrated for first time that immobilized carboxylated single-walled carbon nanotubes (c-SWNTs) offer clear advantages over the use of CNTs. The higher adsorption capacity has been attributed to the special orientation of c-SWNTs molecules on the glass surface. The potential of this new sorbent was evaluated for the preconcentration of non-steroidal anti-inflammatory drugs (NSAIDs) from urine samples. Purified samples were analysed by capillary electrophoresis-mass spectrometry detection allowing the determination of 1.6 to 2.6 microg/L of NSAIDs with only 5 mL of sample. The precision of the method for the determination of real spiked urine samples ranged from 5.4 to 7.4% and the recoveries from 98.6 to 102.2%.