缩合—电解法处理苯胺废水

采用缩合－电解法处理苯胺废水，缩合过程的最佳ＰＨ为５．０－６．０，甲醛的最佳投加量视废水中苯胺含量而定；电解过程中，ＮａＣｌ的最佳投加量为３％（ｗｔ），控制电解液ＰＨ为５．０－７．０、电解时间１２０－１４０ｍｉｎ、槽电压３Ｖ、电流密度０．９Ａ／ｄｍ＾２。在上述条件下，苯胺含量为１０００－１００００ｍｇ／Ｌ的废水经缩合－电解法处理后，ＣＯＤ＜２５０ｍｇ／Ｌ，苯胺＜０．１ｍｇ／Ｌ。     

缩合－电解法处理苯胺废水

采用缩合－电解法处理苯胺废水，缩合过程的最佳ｐＨ为５．０—６．０，甲醛的最佳投加量视废水中苯胺含量而定；电解过程中，ＮａＣｌ的最佳投加量为３％（ｗｔ），控制电解液ｐＨ为５．０—７．０、电解时间１２０—１４０ｍｉｎ、槽电压３Ｖ、电流密度０．９Ａ／ｄｍ￣２。在上述条件下，苯胺含量为１０００—１００００ｍｇ／Ｌ的废水经缩合－电解法处理后，ＣＯＤ＜２５０ｍｇ／Ｌ，苯胺＜０．１ｍｇ／Ｌ。     

流态化电极电解法处理含氰废水

采用细粒膨胀石墨流态化阳极电解法处理含氰量为８０－９０ｍｇ／Ｌ的废水，试验选择出的处理条件为：ｐＨ９－１０，废水流速４２－４５Ｌ／ｈ，槽电流２－３Ａ，ＮａＣｌ加入量１．５－３．０ｇ／Ｌ。同样条件下，使用细粒膨胀石墨流态化电极的电解除氰效果较用简形板状电极好。     

流动注射分光光度法测定废水中挥发酚

基于４－氨基安替比林显色原理,采用流动注射技术,建立了炼油废水中挥发酚的快速测定方法。分析速率为每小时４０个试样,线性范围为０．７５－２３．０ｍｇ／Ｌ。对１．５０ｍｇ／Ｌ苯酚标准溶液连续测定１０次,相对标准偏差为２．８％。对炼油废水样,本法测定结果与标准方法无显著性差异。     

固定化光合细菌处理催化裂化与加氢废水

在２８Ｌ柱式反应器内,沼泽红假单胞菌经软性纤维固定后,连续处理炼油厂催化裂化与加氢废水（此前已经过汽提和厌氧消化预处理）。当反应器进水ＣＯＤ为４７０ｍｇ／Ｌ、废水停留时间为７０ｈ时,出水分离出菌体后,ＣＯＤ小于１００ｍｇ／Ｌ。建立了该处理系统的动力学模型,其参数Ｋｓ＝２９．８ｍｇ／Ｌ,μｍ＝０．０１ｈ－１。     

气相色谱法测定大气中烯烃的研究

采用硅胶－ＡｇＮＯ３富集样品,热解吸进样,气相色谱法分析大气中的烃一,富集过程在常温下进行。当富集样品０．１Ｌ时,乙烯,丙烯,丁二烯的最小检有度分别为０．０００６ｍｇ／ｍ＾３,０．００１ｍｇ／ｍ＾３、０．００４ｍｇ／ｍ＾３,相对标准偏差小于６％,加标回收率９７％－１０９％。     

炼油废水生物脱氮中间试验

对炼油废水中氮氮的生物降解用两种工艺进行了中间试验。试验结果表明,正常工艺条件下,Ｏ／Ｏ工艺处理后出水中ＮＨ３－Ｎ〈２５ｍｇ／Ｌ,ＣＯＤ〈４０ｍｇ／Ｌ,油〈５ｍｇ／Ｌ;Ａ／Ｏ工艺处理后出水中ＮＨ３－Ｎ〈２０ｍｇ／Ｌ,ＣＯＤ〈５０ｍｇ／Ｌ,油〈５ｍｇ／Ｌ,ＮＯ＾３－Ｎ〈１０ｍｇ／Ｌ。     

重力分离—NMC工艺处理对二氯苯生产废水

采用重力分离－ＮＭＣ（中和、混凝、吹脱）工艺处理对二氯苯生产废水，对工艺条件进行了选择试验，选定的最佳工艺条件为：废水静置分层时间５０－６０ｍｉｎ，中和至ＰＨ７，ＰＡＭ投加量５０－７５ｍｇ／Ｌ，空气流量１０ｌ／ｍｉｎ，反应温度５０－５５℃；反应时间６０ｍｉｎ。废水经处理后，苯和氯苯浓度可分别降至１．００ｍｇ／Ｌ和１．１０ｍｇ／Ｌ且可回收９０％以上的苯和氯苯。     

泥法A／O生物脱氮工艺处理腈纶废水和炼油废水

采用泥法Ａ／Ｏ生物脱氮工艺处理腈纶废水和炼油废水,出水中ＣＯＤ〈１００ｍｇ／Ｌ,ＮＨ３－Ｎ〈１５ｍｇ／Ｌ。但进水中油〉２０ｍｇ／Ｌ,ＮＨ３－Ｎ〉７００ｍｇ／Ｌ或ＳＣＮ＾－〉７０ｍｇ／Ｌ时,将对系统产生不良影响。本文介绍了１年来的运行情况,探讨了系统受影响的原因,并提出了改进建议。     

树脂吸附法处理硝基苯和硝基氯苯生产废水的研究

研究了用ＣＨＡ－１１１树脂吸附处理硝基本和硝基氯苯生产废水的最佳工艺条件，当废水中硝基苯类化合物含量为６３９ｍｇ／Ｌ时，ＣＨＡ－１１１树脂的工作吸附容量为１２６ｍｇ／ｍＬ，处理水量为１９０ＢＶ，处理后硝苯类化合物的浓度〈５ｍｇ／Ｌ，去除率〉９９％；采用异丙醇作脱附剂；表明该树脂的吸附与脱附性能良好。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Historical Weathering Based on Chemical Analyses of Two Spodosols in Southern Sweden

Chemical weathering losses were calculated for two conifer stands in relation to ongoing studies on liming effects and ash amendments on chemical status, soil solution chemistry and soil genesis. Weathering losses were based on elemental depletion trends in soil profiles since deglaciation and exposure to the weathering environment. Gradients in total geochemical composition were assumed to reflect alteration over time. Study sites were Horröd and Hasslöv in southern Sweden. Both Horröd and Hasslöv sites are located on sandy loamy Weichselian till at an altitude of 85 and 190 m a.s.l., respectively. Aliquots from volume determined samples from a number of soil levels were fused with lithium metaborate, dissolved in HNO₃, and analysed by ICP – AES. Results indicated highest cumulative weathering losses at Hasslöv. The weathering losses for the elements are in the following order:Si > Al > K > Na > Ca > MgTotal annual losses for Ca+Mg+K+Na, expressed in mmol_c m^-2 yr^-1, amounted to c. 28 and 58 at Horröd and Hasslöv, respectively. Variations between study sites could not be explained by differences in bulk density, geochemistry or mineralogy. The accumulated weathering losses since deglaciation were larger in the uppermost 15 cm than in deeper B horizons for most elements studied.     

Transformations of nitrogen at the interface between the topsoil and an impervious clay subsoil

Much work has been done on gaseous emissions and leaching of nitrogenous compounds from whole soil profiles and also from soil surface measurements which are assumed to be mainly due to topsoil activity. In soils with an impervious clay subsoil, the boundary between the topsoil and subsoil may provide an interface for microbial activity, including N transformations. In this study, we investigated movement and transformations of two reactive N species (nitrate and urea) at the subsoil interface using a series of replicate, intact soil blocks, under two contrasting watering regimes. We measured fluxes in both liquid and gaseous phases and demonstrated that nitrate reaching the subsoil interface does not necessarily leach into water systems, but may denitrify immediately and could, therefore, add to atmospheric pollution through N₂O production. On the other hand, ammonium reaching the subsoil interface either directly, or after mineralization, appears to be more mobile than expected and has the potential to pollute watercourses.     

The Spatial and Temporal Variation of Measured Urban PM10 and PM2.5 in the Helsinki Metropolitan Area

We have studied particulate matter (PM) concentrations,PM₁₀ and PM_2.5, measured in an urban air qualitymonitoring network in the Helsinki Metropolitan Area during1997–1999. The data includes PM₁₀ concentrationsmeasured at five locations (two urban traffic, one suburbantraffic, one urban background and one regional backgroundsite) and PM_2.5 concentrations measured at twolocations (urban traffic and urban background sites). Theconcentrations of PM₁₀ show a clear diurnal variation,as well as a spatial variation within the area. Bycontrast, both the spatial and temporal variation of thePM_2.5 concentrations was moderate. We have analysedthe evolution of urban PM concentrations in terms of therelevant meteorological parameters in the course of oneselected peak pollution episode during 21–31 March, 1998.The meteorological variables considered included wind speedand direction, ambient temperature, precipitation, relativehumidity, atmospheric pressure at the ground level,atmospheric stability and mixing height. The elevated PMconcentrations during the 1998 March episode were clearlyrelated to conditions of high atmospheric pressure,relatively low ambient temperatures and low wind speeds inpredominantly stable atmospheric conditions. The resultsprovide indirect evidence indicating that the PM₁₀concentrations originate mainly from local vehiculartraffic (direct emissions and resuspension), while thePM_2.5 concentrations are mostly of regionally andlong-range transported origin.     

Methane generation from corncobs treated with xylanolytic consortia

Consortia were developed for the treatment of corncobs for use as a feedstock in a biogas fermentor. The treatment of corncobs with xylanolytic consortia enhanced the production of methane and biogas. All five consortia developed produced the maximum biogas and methane at a 6% loading rate and 20 days hydraulic retention time (HRT). The maximum biogas yield of 0.59m³/kg volatile solids (VS) with a methane content of 62% was produced with the KK-10 consortium. This was apparently due to a maximum hemicellulose degradation of 88%.     

Recovery of Acidified Lakes: Lessons From Sudbury, Ontario, Canada

Over 7,000 lakes around Sudbury, Ontario, Canada were acidified by S deposition associated with emissions from the Sudbury metal smelters and more distant S sources. Air pollution controls have led to widespread changes in damaged Sudbury lakes, including increased pH and decreased concentrations of SO₄, metals and base cations. While chemical improvements have often been substantial, many lakes are still acidified, although water quality recovery is continuing. Biological recovery has been observed in some lakes among various groups of organisms including fish, zooplankton, phytoplankton and zoobenthos. Generally, however, biological recovery is still at an early stage. Lakes around Sudbury are also showing that the recovery of acid-damaged lakes is closely linked to the effects of other major environmental stressors such as climate change, base cation depletion and UV-B irradiance. Future studies of the recovery of acid-damaged lakes around Sudbury, and in other regions, will need to consider the interactions of these and other stressors.     

Preparation and Biodegradation of Starch/Polycaprolactone Films

Starch granules were modified with trisodium trimetaphosphate (TSTP) and characterized by P³¹-NMR, FTIR and DSC. Seventy-micron films were prepared from modified starch and polycaprolactone blends by solvent casting technique. Three different types of films—PCL (100% polycaprolactone), MOD-ST/PCL (50% modified starch and 50% polycaprolactone blend) and NONMOD-ST/PCL (50% nonmodified starch and 50% polycaprolactone blends)—were prepared, and their thermal, mechanical, and morphologic properties were investigated to show the increased performance of PCL with the addition of starch and also the effect of modification. It was observed that with the addition of starch the Young's modulus of polycaprolactone was increased and became less ductile, whereas tensile strength and elongation at break values decreased. Biodegradation of these films was inspected under different aerobic environments with the presence of Pseudomonas putida, activated sludge, and compost. It was observed that whereas P. putida had almost no effect on degradation during 90 days, with the presence of activated sludge, considerable deformation of films was observed even in the first 7 days of degradation. In a compost environment, degradation was even faster, and all polymer films were broken into pieces within first 7 days of degradation and no film remained after 15 days.