Real-time monitoring of thermal flavor generation in skim milk powder using atmospheric pressure chemical ionization mass spectrometry

The feasibility of monitoring volatile flavor compounds formed by thermal treatment of skimmed milk powder in real time by atmospheric pressure chemical ionization mass spectrometry (APCIMS) was established. Skim milk powder samples were heated isothermally (70 to 120 degrees C) at different moisture contents (2.2 and 12.7 g water/100 g dry solids). Headspace was sampled and analyzed continuously in full scan mode (30-180 amu) by APCIMS. The identity of the volatile compounds monitored by APCIMS was confirmed by coupled GC-EI-APCIMS. The concentration measured by the APCIMS was the net effect of three processes, namely formation of the compound, partition from the skim milk powder into the gas phase, and dilution due to the headspace sampling method used. Preliminary experiments established that the technique could follow the effects of heating temperature and moisture content on the formation of selected compounds from skim milk powder.     

Inhibition of key aroma compound generated during ultrahigh-temperature processing of bovine milk via epicatechin addition

The ability of epicatechin (EC) to inhibit the thermal development of aroma compounds (i.e., Maillard reaction products) formed during ultrahigh-temperature (UHT) processing of bovine milk was evaluated. Volatile extracts were prepared for two UHT-processed milk samples made from (1) raw milk and (2) raw milk containing 0.1% EC by solvent-assisted flavor evaporation (SAFE) and subsequently analyzed by aroma extract dilution analysis (AEDA). Sensory evaluation was also conducted by a trained panel on the intensity of cooked flavor and bitterness in four UHT-processed milk samples (0.00, 0.01, 0.10, and 0.20% EC added prior to processing), as well as a commercial pasteurized milk sample for comparison. AEDA indicated that addition of EC to raw fluid milk prior to UHT processing reduced the overall thermal formation of key aroma-active compounds in comparison to the traditional UHT milk sample. The largest changes in FD values were reported for methional, furfural, 2-isopropyl-3-methoxypyrazine, 2-acetyl-1-pyrroline, and 2-acetyl-2-thiazoline (Maillard-type aroma compounds) with 32-, 8-, 8-, 4-, and 4-fold reductions in formation, respectively. Sensory evaluation also revealed that all EC-containing UHT milk samples had statistically (P < 0.05) lower cooked flavor intensity in comparison to the control, whereas the 0.2% EC sample was statistically similar to a pasteurized milk sample. Furthermore, addition of EC at or below 0.1% in UHT fluid milk did not significantly increase the bitterness intensity.     

Character impact odorants of high-heat skim milk powder isolated by simultaneous distillation-extraction

To identify the character impact odorant of high-heat skim milk powder (HHSMP), a comparative study using ultrahigh-temperature (UHT) milk was performed. Aroma concentrate was prepared by column adsorption combined with simultaneous distillation-extraction. Aroma extract dilution analysis (AEDA) revealed 58 aroma peaks with flavor dilution (FD) factors ranging from 10 to 3000; from these, 41 compounds were identified and 7 compounds were tentatively identified (FD factor > or = 300). Among these HHSMP and UHT milk components, methyl 2-methyl-3-furyl disulfide and bis(2-methyl-3-furyl) disulfide, which appeared to be generated during the processing of each product, were identified. When the results of the AEDA of both samples were compared, it was considered that the characteristic aroma of HHSMP was not explained by a single compound but instead formed from a mixture of several types of compounds contained in common with the UHT milk. The contribution of these compounds to the aroma of HHSMP was confirmed by an aroma simulation experiment.     

Denaturation of beta-lactoglobulin in pressure-treated skim milk

The kinetics of beta-lactoglobulin (beta-LG) denaturation in pressure-treated reconstituted skim milk samples over a wide pressurization range (100-600 MPa) and at various temperatures (10-40 degrees C) was studied. Denaturation was extremely dependent on the pressure and duration of treatment. At 100 MPa, no denaturation was observed regardless of the temperature or the holding time. At higher pressures, the level of denaturation increased with an increasing holding time at a constant pressure or with increasing pressure at a constant holding time. At 200 MPa, there was only a small effect of changing the temperature at pressurization. However, at higher pressures, increasing the temperature from 10 to 40 degrees C markedly increased the rate of denaturation. The two major genetic variants of beta-LG (A and B) behaved similarly to pressure treatment, although the B variant appeared to denature slightly faster than the A variant at low pressures (< or =400 MPa). The denaturation could be described as a second-order process for both beta-LG variants. There was a marked change in pressure dependence at about 300 MPa, which resulted in markedly different activation volumes in the two pressure ranges. Evaluation of the kinetic and thermodynamic parameters suggested that there may have been a transition from an aggregation-limited reaction to an unfolding-limited reaction as the pressure was increased.     

Rennet-induced aggregation of heated pH-adjusted skim milk

Heated (20-100 °C/0-30 min) skim milks (pH 6.5-7.1) were diluted in buffer (pH 7.0). Rennet was added, and the particle size with time was measured. For all samples, the size initially decreased (lag phase) and then increased (aggregation phase). Milks heated at ≤60 °C had short lag phases and rapid aggregation phases regardless of pH. Milks heated at >60 °C at pH 6.5 had long lag phases and slow aggregation phases. As the pH increased, the lag phase shortened and the aggregation phase accelerated. The aggregation time was correlated with the level of whey protein associated with the casein micelles and with the level of κ-casein dissociated from the micelles. Heated milks formed weak gels when renneted. It is proposed that the milks heated at low pH have whey proteins associated with the casein micelles and that these denatured whey proteins stabilize the micelles to aggregation by rennet and therefore inhibit gelation. In the milks heated at higher pH, the whey proteins associate with κ-casein in the serum and, on rennet treatment, the κ-casein-depleted micelles and the serum-phase whey protein/κ-casein complexes aggregate; however, the denatured whey proteins stabilize the aggregates so that gelation is still inhibited.     

Bipolar membrane electroacidification of demineralized skim milk.

The aim of this study was to evaluate the effect of decreasing the mineral content of skim milk by electrodialysis (ED) prior to electroacidification with bipolar membrane (BMEA) on the performance of the process, the chemical composition, and the physicochemical and functional properties of the isolates produced. ED used to demineralize the skim milk solution was very efficient. However, the electroacidification parameters were influenced by the demineralization level of the skim milk solution: the energy efficiency was decreased with an increase in demineralization, but it was still possible to perform BMEA at a very low conductivity level. Moreover, the isolates produced by BMEA after electrodialysis demineralization at different rates showed similar chemical composition, except on potassium and lactose contents for 75% demineralized isolate. These isolates, except on protein load for 75% demineralization rate, showed similar physicochemical and functional properties, whatever the demineralization rate.     

Physicochemical properties of acidified skim milk gels containing cocoa flavanols

The physicochemical properties of acidified milk gels after the addition of cocoa flavanols were studied. As the flavanol level increased (from 0 to 2.5 mg/g), syneresis and gel elasticity (tan δ) were found to significantly increase and decrease, respectively. Flavanol addition reduced the stress at fracture, with no changes in fracture strain, suggesting that the bond type (i.e., covalent vs noncovalent) was the underlying factor explaining the ease of fracture. Gels made from recombined milks containing the casein fraction of heated milk and the serum of heated flavanol/milk mixtures showed the lowest values of G' and fracture stress. It was concluded that whey proteins/flavanol interactions were responsible for the poor mechanical properties of flavanol-added acidified milk gels. High-performance liquid chromatography analysis of milk sera showed that 60% of the total available monomeric flavanols was found in the serum phase from which 75% was non-associated to whey proteins. Concomitantly, >70% of flavanols with degree of polymerization >3 were found to be associated with the casein fraction.     

The addition of Propionibacterium freudenreichii to Raclette cheese induces biochemical changes and enhances flavor development

Two mixtures of Propionibacterium freudenreichii commercial strains were tested as adjunct cultures in pasteurized milk Raclette cheese to investigate the ability of propionibacteria (PAB) to enhance flavor development. Cheese flavor was assessed by a trained sensory panel, and levels of free amino acids, free fatty acids, and volatile compounds were determined. The PAB level showed a 1.4 log increase within the ripening period (12 weeks at 11 degrees C). Eye formation, which was not desired, was not observed in PAB cheeses. PAB fermented lactate to acetate and propionate and produced fatty acids by lipolysis, branched chain volatile compounds derived from isoleucine and leucine catabolism and some esters. One of the experimental cheeses received the highest scores for odor and flavor intensity and was characterized by higher frequencies of detection for some minor notes ("propionic"and "whey" odor, "sweet" taste). PAB can therefore be considered as potential adjunct cultures to enhance or modify cheese flavor development.     

Molecular water motions of skim milk powder solutions during acidification studied by 17O and 1H nuclear magnetic resonance and rheology

The molecular motion of water was studied in glucono-δ-lactone-acidified skim milk powder (SMP) solutions with various pH values and dry matter contents. NMR relaxometry measurements revealed that lowering the pH in SMP solutions affected 17O and 1H T2 relaxation rates almost identically. Consequently, the present study indicates that the proteins present in the samples do not affect the 1H relaxation behavior markedly, even at relatively high SMP concentrations (15-25%). Comparison of rheological measurements and NMR measurements suggested that the collapse of κ-casein during acidification could contribute to the initial decrease in 17O and 1H relaxation rate in the pH range between 6.6 and 5.5 for 15% SMP and in the pH range between 6.6 and 5.9 for 25% SMP. However, below pH 5.5 the viscosity and 17O and 1H NMR relaxation rates did not correlate, revealing that the aggregation of casein micelles, which increases viscosity below pH 5.5, does not involve major repartitioning of water.     

Rheological properties of acid gels prepared from heated pH-adjusted skim milk

Reconstituted skim milk was adjusted to pH values between 6.5 and 7.1 and heated (90 degrees C) for up to 30 min. The skim milk samples were then readjusted to pH 6.7. Acid gels prepared from heated milk had markedly higher G ' values, a reduced gelation time, and an increased gelation pH than those prepared from unheated milk. An increased pH at heating decreased the gelation time, increased the gelation pH, and increased the final G ' of acid set gels prepared from the heated milk samples. There were only small differences in the level of whey protein denaturation in the samples at different pH values, and these differences could not account for the differences in the G ' of the acid gels. The levels of denatured whey protein associated with the casein micelles decreased and the levels of soluble denatured whey proteins increased as the pH at heating was increased. The results indicated that the soluble denatured whey proteins had a greater effect on the final G ' of the acid gels than the denatured whey proteins associated with the casein micelles.     

Effect of cationic membrane permselectivity on the efficiency of skim milk electroacidification

Bipolar membrane electroacidification (BMEA) uses the property of bipolar membranes to split water and the demineralization action of cation-exchange membranes (CEM). As milk mineral salt content is very sensitive to ionic strength and pH changes, the aim of this study was to better understand the effect of changes in mineral content during pH decrease and demineralization of skim milk. The objectives were to investigate the effect of different cationic permselective membranes (CSV and CMX membranes) on skim milk cation migration and protein precipitation during BMEA. The permselectivity of both membranes tested does not influence the final efficiency of BMEA. The purity of the bovine milk casein isolates produced was similar to or higher (97-98% versus 93.4-96.7) than those of commercial isolates, due to a reduced ash content (1.2 versus 2.0-3. 8%) resulting from the CEM demineralizing phenomenon. For both membranes, the main ionic species to migrate was the potassium ions.     

Properties and stability of oil-in-water emulsions stabilized by coconut skim milk proteins

Protein fractions were isolated from coconut: coconut skim milk protein isolate (CSPI) and coconut skim milk protein concentrate (CSPC). The ability of these proteins to form and stabilize oil-in-water emulsions was compared with that of whey protein isolate (WPI). The solubility of the proteins in CSPI, CSPC, and WPI was determined in aqueous solutions containing 0, 100, and 200 mM NaCl from pH 3 to 8. In the absence of salt, the minimum protein solubility occurred between pH 4 and 5 for CSPI and CSPC and around pH 5 for WPI. In the presence of salt (100 and 200 mM NaCl), all proteins had a higher solubility than in distilled water. Corn oil-in-water emulsions (10 wt %) with relatively small droplet diameters (d32 approximately 0.46, 1.0, and 0.5 mum for CSPI, CSPC, and WPI, respectively) could be produced using 0.2 wt % protein fraction. Emulsions were prepared with different pH values (3-8), salt concentrations (0-500 mM NaCl), and thermal treatments (30-90 degrees C for 30 min), and the mean particle diameter, particle size distribution, zeta-potential, and creaming stability were measured. Considerable droplet flocculation occurred in the emulsions near the isoelectric point of the proteins: CSPI, pH approximately 4.0; CSPC, pH approximately 4.5; WPI, pH approximately 4.8. Emulsions with monomodal particle size distributions, small mean droplet diameters, and good creaming stability could be produced at pH 7 for CSPI and WPI, whereas CSPC produced bimodal distributions. The CSPI and WPI emulsions remained relatively stable to droplet aggregation and creaming at NaCl concentrations of < or =50 and < or =100 mM, respectively. In the absence salt, the CSPI and WPI emulsions were also stable to thermal treatments at < or =80 and < or =90 degrees C for 30 min, respectively. These results suggest that CSPI may be suitable for use as an emulsifier in the food industry.     

Volatile flavor components of stored nonfat dry milk.

Nonfat dry milk (NDM) is widely used both as an ingredient in other preparations and for direct consumption. Flavor quality of NDM is a critical parameter because it can directly impact final product quality. Flavors can be formed in NDM during subsequent storage. Identification of compounds responsible for storage-induced flavors is necessary to correlate sensory quality with potential sources of the flavors. Six NDM samples were selected for volatile flavor analysis based on sensory analysis and storage time. Volatile components were extracted by direct solvent extraction/high vacuum distillation. Volatile extracts were separated into neutral/basic and acidic fractions and analyzed by gas chromatography-olfactometry (GCO) and aroma extract dilution analysis (AEDA). A variety of aldehydes, ketones, and free fatty acids were responsible for generation of flavors in stored NDM. The following compounds exhibited high aroma impact by AEDA: 3-(methylthio)propanal (boiled potato); o-aminoacetophenone (corn tortilla); 2,5-dimethyl-4-hydroxy-3(2H)-furanone and 2-methyl-3-hydroxy-4H-pyran-4-one (burnt sugar); butanoic acid (cheesy); pentanoic acid (sweaty); acetic and hexanoic acids (sour/vinegar); octanoic, decanoic, and dodecanoic acids (waxy); p-cresol (cowy/barny); 3-methylindole (fecal); dimethyl trisulfide (cabbage); (E,E)-2,4-decadienal (fried/fatty); furfuryl alcohol (rubber/vitamin); phenylacetic acid (rose-like); and 1-octen-3-one (mushroom).     

Screening method for vitamins A and D in fortified skim milk, chocolate milk, and vitamin D liquid concentrates

Vitamin A was determined in fortified chocolate milk and skim milk; vitamin D was determined in fortified chocolate milk, skim milk, and vitamin D concentrates, using reverse phase high pressure liquid chromatography (HPLC). The sample is saponified, extracted with hexane, and chromatographed in an HPLC system on a 10 micron Vydac TP reverse phase C18 column, using acetonitrile-methanol (9+1) as the mobile phase. For 6 replicates, the recoveries of vitamins A and D, using this procedure, were 99 and 98%, respectively.     

Role of kappa-casein in the association of denatured whey proteins with casein micelles in heated reconstituted skim milk

Reconstituted skim milk at pH from 6.5 to 7.1 was unheated, preheated (68 degrees C/20 min), or heated at 90 degrees C for 20-30 min. On preheating, the size of the casein micelles decreased by about 5-20 nm, with a greater effect at higher pH. The casein micelle size of the heated milk at pH 6.5 increased by about 30 nm when compared to that of the unheated or preheated milk. As the pH was increased before heating, the particle size gradually decreased so that, at pH 7.1, the size was markedly smaller than that for the unheated milk and slightly smaller than that for the preheated milk. High levels (about 85%) of denatured whey protein associated with the casein micelles at pH 6.5, and this level decreased as the pH increased so that, at pH 7.1, low levels (about 15%) were associated with the micelles. Low levels of alphaS-casein and beta-casein were found in the serum regardless of the heat treatment or the pH of the milk. At pH 6.5, low levels (about 10%) of kappa-casein were also found in the milk serum. In the unheated milk, the level of serum kappa-casein increased slightly with increasing pH; in the heated samples, the level of serum kappa-casein increased markedly and linearly with increasing pH so that, at pH 7.1, about 70% of the kappa-casein was in the serum phase. The results of this study indicate that the pH dependence of the levels of serum phase kappa-casein may be responsible for the change in distribution of the whey proteins between the colloidal and serum phases. This is the first report to demonstrate significant levels of dissociation of kappa-casein from the micelles at pH between 6.5 and 6.7, although this dissociation phenomenon is well known on heating milk at high temperatures at pH above 6.7.     

Role of the soluble and micelle-bound heat-induced protein aggregates on network formation in acid skim milk gels

Gel formation was monitored by low amplitude rheometry during acidification at 40 degrees C with 1.5% glucono-delta-lactone in combined milk systems containing soluble and/or micelle-bound heat-induced (95 degrees C/10 min) aggregates of denatured whey proteins and kappa-casein and in heated dairy mixes with varying micellar casein/whey protein ratio (CN/WP). Both soluble and micelle-bound aggregates increased gelation pH and gel strength. Micelle-bound aggregates seemed to modify the micelle surface so that micelles were destabilized at a pH of 5.1 (instead of 4.7), while soluble aggregates precipitated at their calculated pI of approximately 5.3, and initiated an early gelation by interacting with the micelles. Decreasing the CN/WP ratio produced larger aggregates with higher whey protein: kappa-casein ratio, which gave more elastic gels. The specific effects of the micellar and soluble aggregates on gel strength are discussed with respect to their relative proportions in the heated milk.     

Effect of pH on the association of denatured whey proteins with casein micelles in heated reconstituted skim milk

Skim milk was adjusted to pH values between 6.5 and 6.7 and heated (80, 90, and 100 degrees C) for up to 60 min. Changes in casein micelle size, level of whey protein denaturation, and level of whey protein association with the micelles were monitored for each milk sample. Changes in casein micelle size were markedly affected by the pH at heating. At low pH (6.5-6.55), the casein micelle size increased markedly during the early stages of heating, and the size plateaued on prolonged heating. The maximum increase in size was approximately 30-35 nm. In contrast, at high pH (6.7), much smaller changes in size were observed on heating and the maximum increase in size was only approximately 10 nm. An intermediate behavior was observed at pH values between these two extremes. The rate of denaturation of the major whey proteins, alpha-lactalbumin and beta-lactoglobulin, was essentially unaffected by the pH at heating for the small pH changes involved in this study, and the changes in casein micelle size were poorly related to the level of whey protein denaturation. In contrast, the level of denatured whey proteins associating with the micelles was markedly dependent on the pH at heating, with high levels of association at pH 6.5-6.55 and low levels of association at pH 6.7. Changes in casein micelle size were related to the levels of denatured whey proteins that were associated with the casein micelles, although there was a small deviation from linearity at low levels of association (<15%). Further studies on reconstituted and fresh milk samples at smaller pH steps confirmed that the association of whey proteins with the casein micelles was markedly affected by the pH at heating. These results indicate that the changes in casein micelle size induced by the heat treatment of skim milk were a consequence of the whey proteins associating with the casein micelles and that the level of association was markedly influenced by small pH changes of the milk. It was not possible to determine whether the association itself influenced the casein micelle size or whether parallel reactions involving micellar aggregation caused the increase in micelle size as whey protein association progressed.     

Characterization of heat-induced changes in skim milk using asymmetrical flow field-flow fractionation coupled with multiangle laser light scattering

Separation and size measurement of protein particles are a relevant approach to monitor heat-induced changes in skim milk. Unfortunately, no method is currently available at low cost and without excessive preparation of the samples. Therefore, the present study aimed at evaluating the interest of asymmetrical flow field-flow fractionation (AFlFFF) coupled with multiangle laser light scattering (MALLS) for this purpose. Unheated and heated skim milk samples at pH 6.5 and 7.2 were prepared and comparatively analyzed using AFlFFF-MALLS, size exclusion chromatography (SEC-MALLS) and dynamic light scattering. The results showed that AFlFFF could evidence the conversion of the native whey proteins of unheated milk into heat-induced whey protein/κ-casein complexes in the serum phase of milk and possibly on the surface of the casein micelles. The pH-induced changes in the partition of the complexes between the serum and the micellar phases could also be observed. The results therefore showed the interest of AFlFFF-MALLS to monitor the heat-induced changes in particle sizes in skim milk and to separate the different protein components of unheated and heated skim milk.     

Effects of heat and high hydrostatic pressure treatments on disulfide bonding interchanges among the proteins in skim milk

Traditionally, milk has been heat treated to control microorganisms and to alter its functionality, for example, to increase its heat stability. Pressure treatment has been considered as a possible alternative for microorganism control, but some of the functionality-related milk protein interactions have not been explored. The present study used two novel two-dimensional polyacrylamide gel electrophoresis (2D PAGE) methods to explore the differences in the irreversible disulfide bond changes among the milk proteins after four common heat treatments and after 30-min pressure treatments of milk at 200, 400, 600, and 800 MPa at ambient temperature (22 degrees C). The pasteurizing heat treatment (72 degrees C for 15 s) denatured and aggregated only a few minor whey proteins, but the high heat treatments (100 degrees C for 120 s, 120 degrees C for 120 s, and 140 degrees C for 5 s) formed disulfide-bonded aggregates that included a high proportion of all of the whey proteins and kappa-casein (kappa-CN) and a proportion of the alpha(s2)-CN. Pressure treatment of milk at 200 MPa caused beta-lactoglobulin (beta-LG) to form disulfide-bonded dimers and incorporated beta-LG into aggregates, probably disulfide-bonded to kappa-CN. The other whey proteins appeared to be less affected at 200 MPa for 30 min. In contrast, pressure treatment at 800 MPa incorporated beta-LG and most of the minor whey proteins, as well as kappa-CN and much of the alpha(s2)-CN, into aggregates. The accessibility of alpha(s2)-CN and formation of complexes involving alpha(s2)-CN, kappa-CN, and whey proteins in the pressure treated milk is an important novel finding. However, only some of the alpha-lactalbumin was denatured or incorporated into the large aggregates. These and other results show that the differences between the stabilities of the proteins and the accessibilities of the disulfide bonds of the proteins at high temperature or pressure affect the formation pathways that give the differences among the resultant aggregates, the sizes of the aggregates, and the product functionalities.