阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

具有p-GaN岛状埋层耐压结构的横向AlGaN/GaN高电子迁移率晶体管

GaN基高电子迁移率晶体管(HEMT)相对较低的击穿电压严重限制了其大功率应用.为了进一步改善器件的击穿特性,通过在n-GaN外延缓冲层中引入六个等间距p-GaN岛掩埋缓冲层(PIBL)构成p-n结,提出一种基于p-GaN埋层结构的新型高耐压AlGaN/GaN HEMT器件结构.Sentaurus TCAD仿真结果表明,在关态高漏极电压状态下,p-GaN埋层引入的多个反向p-n结不仅能够有效调制PIBL AlGaN/GaN HEMT的表面电场和体电场分布,而且对于缓冲层泄漏电流有一定的抑制作用,这保证了栅漏间距为10μm的PIBL HEMT能够达到超过1700 V的高击穿电压(BV),是常规结构AlGaN/GaN HEMT击穿电压(580 V)的3倍.同时,PIBL结构AlGaN/GaN HEMT的特征导通电阻仅为1.47 m?·cm~2,因此获得了高达1966 MW·cm~(-2)的品质因数(FOM=BV~2/R_(on,sp)).相比于常规的AlGaN/GaN HEMT,基于新型p-GaN埋岛结构的HEMT器件在保持较低特征导通电阻的同时具有更高的击穿电压,这使得该结构在高功率电力电子器件领域具有很好的应用前景.     

新型Si3N4层部分固定正电荷AlGaN／GaNHEMTs器件耐压分析

为了优化传统AlGaN／GaNhighelectronmobilitytransistors结构表面电场分布,提高器件击穿电压和可靠性,本文利用不影响AlGaN／GaN异质结极化效应的Si3N4钝化层电荷分布,提出了一种sbN4钝化层部分固定正电荷AIGaN／GaNhighelectronmobilitytransistors新结构．SiaN4钝化层中部分固定正电荷通过电场调制效应使表面电场分布中产生新的电场峰而趋于均匀．新电场峰使得新结构栅边缘和漏端高电场有效降低,器件击穿电压从传统结构的296V提高到新结构的650V,而且可靠性改善．通过Si3N4与AlGaN界面横、纵向电场分布,说明了产生表面电场峰的电场调制效应,为设计SiaN4层部分固定正电荷新结构提供了科学依据．Si3N4钝化层部分固定正电荷的补偿作用,使沟道二维电子气浓度增加,导通电阻减小,输出电流提高．     

基于凹槽结构抑制AlGaN/GaN高电子迁移率晶体管电流崩塌效应

基于双脉冲技术,研究了GaN缓冲层陷阱对AlGaN/GaN高电子迁移率晶体管电流崩塌效应的影响.结果表明,栅边缘漏侧的电场峰值使得沟道电子跃迁至缓冲层,并被缓冲层中的陷阱俘获是造成电流崩塌的主要原因之一.提出了势垒层局部凹槽结构,降低了栅边缘漏侧的电场峰值,使电场分布更加均匀,改善了器件的电流崩塌效应.与传统AlGaN/GaN高电子迁移率晶体管结构相比,新器件结构对电流崩塌效应的抑制作用至少提升了22.30%.     

高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

F离子注入新型Al0．25Ga0．75N／GaNHEMT器件耐压分析

为了缓解AlGaN／GaNhighelectronmobilitytransistors（HEMT）器件n型GaN缓冲层高的泄漏电流,本文提出了具有氟离子注入新型Al0．25Ga0．75N／GaNHEMT器件新结构．首先分析得出n型GaN缓冲层没有受主型陷阱时,器件输出特性为欧姆特性,这样就从理论和仿真方面解释了文献生长GaN缓冲层掺杂Fe,Mg等离子的原因．利用器件输出特性分别分析了栅边缘有和没有低掺杂漏极时,氟离子分别注入源区、栅极区域和漏区的情况,得出当氟离子注入源区时,形成的受主型陷阱能有效俘获源极发射的电子而减小GaN缓冲层的泄漏电流,击穿电压达到262v通过减小GaN缓冲层体泄漏电流,提高器件击穿电压,设计具有一定输出功率新型A1GaN／GaNHEMT提供了科学依据．     

Al2O3绝缘层的AlGaN/GaN MOSHEMT器件研究

在研制AlGaN/GaN HEMT器件的基础上,采用ALD法制备了Al2O3 AlGaN/GaN MOSHEMT器件.通过X射线光电子能谱测试表明在AlGaN/GaN异质结材料上成功淀积了Al2O3薄膜.根据对HEMT和MOSHEMT器件肖特基电容、器件输出以及转移特性的测试进行分析发现:所制备的Al2O3,薄膜与AlGaN外延层间界面态密度较小,因而MOSHEMT器件呈现出较好的栅控性能;其次,该器件的栅压可以加至 3 V,此时的最大饱和电流达到800 mA/mm,远远高于肖特基栅HEMT器件的最大输出电流;而且栅漏反偏状态下的泄漏电流却减小了两个数量级,提高了器件的击穿电压,通过进一步分析认为泄漏电流主要来源于Fowler-Nordheim隧穿.     

高线性度Al_xGa_(1-x)N/Al_yGa_(1-y)N/GaN高电子迁移率晶体管优化设计

对新型复合沟道AlxGa1-xN/AlyGa1-yN/GaN高电子迁移率晶体管(HEMT)进行了优化设计.从半导体能带理论与量子阱理论出发,自洽求解了器件层结构参数对器件导带能级以及二维电子气(2DEG)中载流子浓度和横向电场的影响.用TCAD软件仿真得到了器件的层结构参数对器件性能的影响.结合理论分析和仿真结果确定了器件的最佳外延层结构Al0.31Ga0.69N/Al0.04Ga0.96N/GaNHEMT.对栅长1μm,栅宽100μm的器件仿真表明,器件的最大跨导为300mS/mm,且在栅极电压-2—1V的宽范围内跨导变化很小,表明器件具有较好的线性度;器件的最大电流密度为1300mA/mm,特征频率为11.5GHz,最大振荡频率为32.5GHz.     

1000 V p-GaN混合阳极AlGaN/GaN二极管

GaN材料具有优异的电学特性,如大的禁带宽度(3.4 eV)、高击穿场强(3.3 MV/cm)和高电子迁移率(600 cm~2/(V·s)). AlGaN/GaN异质结由于压电极化和自发极化效应,产生高密度(1×10~(13)cm~(-2))和高迁移率(2000 cm~2/(V·s))的二维电子气(2DEG),在未来的功率系统中, AlGaN/GaN二极管具有极大的应用前景.二极管的开启电压和击穿电压是影响其损耗和功率处理能力的关键参数,本文提出了一种新型的具有高阻盖帽层(high-resistance-cap-layer, HRCL)的p-GaN混合阳极AlGaN/GaN二极管来优化其开启电压和击穿特性.在p-GaN/AlGaN/GaN材料结构基础上,通过自对准的氢等离子体处理技术,在沟道区域形成高阻盖帽层改善电场分布,提高击穿电压,同时在阳极区域保留p-GaN结构,用于耗尽下方的二维电子气,调控开启电压.制备的p-GaN混合阳极(p-GaN HRCL)二极管在阴阳极间距Lac为10μm时,击穿电压大于1 kV,开启电压+1.2 V.实验结果表明, p-GaN混合阳极和高阻GaN盖帽层的引入,有效改善AlGaN/GaN肖特基势垒二极管电学性能.     

Breakdown voltage analysis of Al0.25Ga0.75N/GaN high electron mobility transistors with partial silicon doping in the AlGaN layer

In this paper,two-dimensional electron gas（2DEG） regions in AlGaN/GaN high electron mobility transistors（HEMTs） are realized by doping partial silicon into the AlGaN layer for the first time.A new electric field peak is introduced along the interface between the AlGaN and GaN buffer by the electric field modulation effect due to partial silicon positive charge.The high electric field near the gate for the complete silicon doping structure is effectively decreased,which makes the surface electric field uniform.The high electric field peak near the drain results from the potential difference between the surface and the depletion regions.Simulated breakdown curves that are the same as the test results are obtained for the first time by introducing an acceptor-like trap into the N-type GaN buffer.The proposed structure with partial silicon doping is better than the structure with complete silicon doping and conventional structures with the electric field plate near the drain.The breakdown voltage is improved from 296 V for the conventional structure to 400 V for the proposed one resulting from the uniform surface electric field.     

Breakdown voltage analysis of Al_0.25Ga_0.75N/GaN high electron mobility transistors with partial silicon doping in the AlGaN layer

In this paper,two-dimensional electron gas(2DEG) regions in AlGaN/GaN high electron mobility transistors(HEMTs) are realized by doping partial silicon into the AlGaN layer for the first time.A new electric field peak is introduced along the interface between the AlGaN and GaN buffer by the electric field modulation effect due to partial silicon positive charge.The high electric field near the gate for the complete silicon doping structure is effectively decreased,which makes the surface electric field uniform.The high electric field peak near the drain results from the potential difference between the surface and the depletion regions.Simulated breakdown curves that are the same as the test results are obtained for the first time by introducing an acceptor-like trap into the N-type GaN buffer.The proposed structure with partial silicon doping is better than the structure with complete silicon doping and conventional structures with the electric field plate near the drain.The breakdown voltage is improved from 296 V for the conventional structure to 400 V for the proposed one resulting from the uniform surface electric field.     

An AlGaN/GaN HEMT with a reduced surface electric field and an improved breakdown voltage

A reduced surface electric field in an AlGaN/GaN high electron mobility transistor(HEMT) is investigated by employing a localized Mg-doped layer under the two-dimensional electron gas(2-DEG) channel as an electric field shaping layer.The electric field strength around the gate edge is effectively relieved and the surface electric field is distributed evenly as compared with those of HEMTs with conventional source-connected field plate and double field plate structures with the same device physical dimensions.Compared with the HEMTs with conventional sourceconnected field plates and double field plates,the HEMT with a Mg-doped layer also shows that the breakdown location shifts from the surface of the gate edge to the bulk Mg-doped layer edge.By optimizing both the length of Mg-doped layer,L m,and the doping concentration,a 5.5 times and 3 times the reduction in the peak electric field near the drain side gate edge is observed as compared with those of the HEMTs with source-connected field plate structure and double field plate structure,respectively.In a device with V GS = -5 V,L m = 1.5 μm,a peak Mg doping concentration of 8×10 17cm-3 and a drift region length of 10 μm,the breakdown voltage is observed to increase from 560 V in a conventional device without field plate structure to over 900 V without any area overhead penalty.     

An AlGaN/GaN HEMT with reduced surface electric field and improved breakdown voltage

A reduced surface electric field in AlGaN/GaN high electron mobility transistor (HEMT) is investigated by employing a localized Mg-doped layer under the two-dimensional electron gas (2-DEG) channel as an electric field shaping layer. The electric field strength around the gate edge is effectively relieved and the surface electric field is distributed evenly as compared with those of HEMTs with conventional source-connected field plate and double field plate structures with the same device physical dimensions. Compared with the HEMTs with conventional source-connected field plate and double field plate, the HEMT with Mg-doped layer also shows that the breakdown location shifts from the surface of the gate edge to the bulk Mg-doped layer edge. By optimizing both the length of Mg-doped layer, L_m, and the doping concentration, a 5.5 times and 3 times the reduction in the peak electric field near the drain side gate edge is observed as compared with those of the HEMTs with source-connected field plate structure and double field plate structure, respectively. In a device with V_GS=-5 V, L_m=1.5 μm, a peak Mg doping concentration of 8× 10¹⁷ cm^-3 and a drift region length of 10 μm, the breakdown voltage is observed to increase from 560 V in a conventional device without field plate structure to over 900 V without any area overhead penalty.     

Breakdown mechanisms in AlGaN/GaN high electron mobility transistors with different GaN channel thickness values

In this paper,the off-state breakdown characteristics of two different AlGaN/GaN high electron mobility transistors（HEMTs）,featuring a 50-nm and a 150-nm GaN thick channel layer,respectively,are compared.The HEMT with a thick channel exhibits a little larger pinch-off drain current but significantly enhanced off-state breakdown voltage(SV_off).Device simulation indicates that thickening the channel increases the drain-induced barrier lowering（DIBL） but reduces the lateral electric field in the channel and buffer underneath the gate.The increase of BV_off in the thick channel device is due to the reduction of the electric field.These results demonstrate that it is necessary to select an appropriate channel thickness to balance DIBL and BV_off in AlGaN/GaN HEMTs.     

Ni/Au Schottky gate oxidation and BCB passivation for high-breakdown-voltage AlGaN/GaN HEMT

A new AlGaN/GaN high electron mobility transistor (HEMT) employing Ni/Au Schottky gate oxidation and benzocyclobutene (BCB) passivation is fabricated in order to increase a breakdown voltage and forward drain current. The Ni/Au Schottky gate metal with a thickness of 50/300 nm is oxidized under oxygen ambient at 500 C and the highly resistive NiO is formed at the gate edge. The leakage current of AlGaN/GaN HEMTs is decreased from 4.94 μA to 3.34 nA due to the formation of NiO. The BCB, which has a low dielectric constant, successfully passivates AlGaN/GaN HEMTs by suppressing electron injection into surface states. The BCB passivation layer has a low capacitance, so BCB passivation increases the switching speed of AlGaN/GaN HEMTs compared with silicon nitride passivation, which has a high dielectric constant. The forward drain current of a BCB-passivated device is 199 mA /mm, while that of an unpassivated device is 172 mA /mm due to the increase in two-dimensional electron gas (2DEG) charge.     

Theoretical analytic model for RESURF AlGaN/GaN HEMTs

In this paper, we propose a two-dimensional(2D) analytic model for the channel potential and electric field distribution of the RESURF AlGaN/GaN high electron mobility transistors(HEMTs). The model is constructed by two-dimensional Poisson's equation with appropriate boundary conditions. In the RESURF AlGaN/GaN HEMTs, we utilize the RESURF effect generated by doped negative charge in the AlGaN layer and introduce new electric field peaks in the device channels,thus, homogenizing the distribution of electric field in channel and improving the breakdown voltage of the device. In order to reveal the influence of doped negative charge on the electric field distribution, we demonstrate in detail the influences of the charge doping density and doping position on the potential and electric field distribution of the RESURF AlGaN/GaN HEMTs with double low density drain(LDD). The validity of the model is verified by comparing the results obtained from the analytical model with the simulation results from the ISE software. This analysis method gives a physical insight into the mechanism of the AlGaN/GaN HEMTs and provides reference to modeling other AlGaN/GaN HEMTs device.     

AlGaN表面坑状缺陷及GaN缓冲层位错缺陷对AlGaN/GaN HEMT电流崩塌效应的影响

利用金属有机气相外延(MOVPE)技术生长了具有不同AlGaN表面坑状缺陷和GaN缓冲层位错缺陷密度的AlGaN/GaN 高电子迁移率晶体管(HEMT)样品,并对比研究了两种缺陷对器件栅、漏延迟电流崩塌效应的影响.栅延迟测试表明,AlGaN表面坑状缺陷会引起栅延迟电流崩塌效应和源漏电阻的增加,而且表面坑状缺陷越多,栅延迟电流崩塌程度和源漏电阻的增加越明显.漏延迟测试显示,AlGaN表面坑状缺陷对漏延迟电流崩塌影响不大,而GaN缓冲层位错缺陷主要影响漏延迟电流崩塌.研究结果表明,AlGaN表面坑状缺陷和Ga 关键词： AlGaN/GaN HEMT 电流崩塌 坑状缺陷 位错缺陷