Processing and Properties of TiB2 with MoSi2 Sinter-additive: A First Report

The densification of non-oxide ceramics like titanium boride (TiB₂) has always been a major challenge. The use of metallic binders to obtain a high density in liquid phase-sintered borides is investigated and reported. However, a non-metallic sintering additive needs to be used to obtain dense borides for high-temperature applications. This contribution, for the first time, reports the sintering, microstructure, and properties of TiB₂ materials densified using a MoSi₂ sinter-additive. The densification experiments were carried out using a hot-pressing and pressureless sintering route. The binderless densification of monolithic TiB₂ to 98% theoretical density with 2–5 μm grain size was achieved by hot pressing at 1800°C for 1 h in vacuum. The addition of 10–20 wt% MoSi₂ enables us to achieve 97%–99%ρ_th in the composites at 1700°C under similar hot-pressing conditions. The densification mechanism is dominated by liquid-phase sintering in the presence of TiSi₂. In the pressureless sintering route, a maximum of 90%ρ_th is achieved after sintering at 1900°C for 2 h in an (Ar+H₂) atmosphere. The hot-pressed TiB₂–10 wt% MoSi₂ composites exhibit high Vickers hardness (∼26–27 GPa) and modest indentation toughness (∼4–5 MPa·m^1/2).     

Effect of SiC on Interfacial Reaction and Sintering Mechanism of TiB2

Compacts of TiB₂ with densities approaching 100% are difficult to obtain using pressureless sintering. The addition of SiC was very effective in improving the sinterability of TiB₂. The oxygen content of the raw TiB₂ powder used in this research was 1.5 wt%. X-ray photoelectron spectroscopy showed that the powder surface consisted mainly of TiO₂ and B₂O₃. Using vacuum sintering at 1700°C under 13–0.013 Pa, TiB₂ samples containing 2.5 wt% SiC achieved 96% of their theoretical density, and a density of 99% was achieved by HIPing. TEM observations revealed that SiC reacts to form an amorphous phase. TEM-EELS analysis indicated that the amorphous phase includes Si, O, and Ti, and X-ray diffraction showed the reaction to be TiO₂+ SiC → SiO₂+ TiC. Therefore, the improved sinterability of TiB₂ resulted from the SiO₂ liquid phase that was formed during sintering when the raw TiB₂ powder had 1.5 wt% oxygen.     

Mechanochemical Synthesis and Pressureless Sintering of TiB2–AlN Composites

TiB₂-AlN composites have been fabricated by the pressureless sintering of a mechanochemically processed Ti, Al, and BN powder mixture. TiB₂-AlN powder was obtained from the mixture of Ti, Al, and BN, which had a composition corresponding to 45.7 wt% TiB₂-54.3 wt% AlN, after mechanochemical processing for longer than 24 h. X-ray diffraction and transmission electron microscopy analysis showed that the powder subjected to mechanochemical processing for 60 h consisted of crystallites less than 300 nm in size with a disordered crystal structure. TiB₂-AlN composites with 95% relative density, a flexural strength of 172 MPa, a fracture toughness of 4.6 MPa·m^1/2, a hardness of 12.0 GPa, and an electrical resistivity of 1488 μΩ·cm were obtained by pressureless sintering at 1700°C for 2 h of the powder subjected to mechanochemical processing for 60 h.     

Effect of Double Reinforcements on Elevated-Temperature Strength and Toughness of Molybdenum Disilicide

Flexural strength and fracture toughness of molybdenum disilicide and its composites with 10 wt% TiB₂ and 10 wt% TiB₂+ 10 wt% SiC, synthesized by the hot-pressing technique, were evaluated as a function of temperature, ranging from ambient temperature to 1600°C. Results show that the composites have higher strength and slightly lower toughness as compared with monolithic MoSi₂ at room temperature. At high temperatures, the composites exhibit higher strength as well as higher toughness vis-à-vis monolithic MoSi₂. Among the composites, the double reinforcement of SiC and TiB₂ was found to be more effective in improving the mechanical properties. A transition from brittle to ductile behavior was observed at temperatures greater than 1300°C for all materials tested. The high-temperature mechanical behavior was found to be significantly influenced by the flow of an intergranular glassy phase and the attendant cavity nucleation and growth along the grain boundaries. Micromechanisms responsible for the ambient as well as the elevated-temperature property improvement in composites are discussed with the aid of fractography.     

Polytypes, Grain Growth, and Fracture Toughness of Metal Boride Particulate SiC Composites

In order to understand the relation between microstructure and toughening behavior in SiC materials, NbB₂, TaB₂, TiB₂, and ZrB₂ particulate SiC composites were fabricated with pressureless sintering. In the composites, 3(cubic)-SiC powder was used as starting material for the matrix. The p-SiC powder transformed to a(noncubic) phase during sintering. The transformation, the behavior of which was influenced by the existence of metal boride particles, was accompanied by normal or exaggerated grain growth. The metal boride particles suppressed large-scale exaggerated grain growth of SiC, and it had a tendency to simulate grain growth with a high aspect ratio of the SiC grains. Increase in the fracture toughness of the composites was observed when the grain size and the aspect ratio of the SiC grains increased together. The toughening behavior is discussed based on a grain bridging mechanism.     

Solid-State Diffusion Bonding of Carbon–Carbon Composites with Borides and Carbides

Solid-state diffusion bonding of carbon–carbon (C─C) composites by using boride and carbide interlayers has been investigated. The interlayer materials used in this study were single-phase borides (TiB₂ or ZrB₂), eutectic mixtures of borides and carbides (ZrB₂+ ZrC or TiB₂+ B₄C), and mixtures of TiB₂+ SiC + B₄C produced in situ by chemical reactions between B₄C, Ti, and Si or between TiC, Si, and B. The double-notch shear strengths of the joints produced by solid-state reaction sintering of B₄C + Ti + Si interlayers were much higher than those of joints produced with other interlayers. The maximum strength was achieved for C─C specimens bonded at 2000°C with a 2:1:1 mole ratio of Ti, Si, and B₄C powders. The reaction products identified in the interlayers, after joining, were TiB₂, SiC, and TiC. The joint shear strength increased with the test temperature, from 8.99 MPa at room temperature to an average value of 14.51 MPa at 2000°C.     

Pressureless Sintering of High-Density ZrB2–SiC Ceramic Composites

Ultra-high-temperature ceramic composites of ZrB₂ 20 wt%SiC were pressureless sintered under an argon atmosphere. The starting ZrB₂ powder was synthesized via the sol–gel method with a small crystallite size and a large specific surface area. Dry-pressed compacts using 4 wt% Mo as a sintering aid can be pressureless sintered to ∼97.7% theoretical density at 2250°C for 2 h. Vickers hardness and fracture toughness of the sintered ceramic composites were 14.82±0.25 GPa and 5.39±0.13 MPa·m^1/2, respectively. In addition to the good sinterability of the ZrB₂ powders, X-ray diffraction and scanning electron microscopy results showed that Mo formed a solid solution with ZrB₂, which was believed to be beneficial for the densification process.     

Reaction Processing of Al2O3 Composites Containing Iron and Iron Aluminides

Different Fe-Al₂O₃ and FeAl-Al₂O₃ composites with metallic contents up to 30 vol% have been fabricated via reaction processing of Al₂O₃, Fe, and Al mixtures. Low Al contents (<∼10 vol%) within the starting mixture lead to composites consisting of Fe embedded in an Al₂O₃ matrix, whereas aluminide-containing Al₂O₃ composites result from powder mixtures with higher Al contents. In both cases, densification up to 98% TD can be achieved by pressureless sintering in inert atmosphere at moderate temperatures (1450°-1500°C). The proposed reaction sintering mechanism includes the reduction of native oxide layers on the surface of the Fe particles by Al and, in the case of mixtures with high Al contents, aluminide formation followed by sintering of the composites. Density and bending strengths of the reaction-sintered composites depend strongly on the Al content of the starting mixture. In the case of samples containing elemental Fe, crack path observations indicate the potential for an increase of fracture toughness, even at room temperature, by crack bridging of the ductile Fe inclusions.     

Densification, Sintering Reactions, and Properties of Titanium Diboride With Titanium Disilicide as a Sintering Aid

In the present investigation, we explore the feasibility of using TiSi₂ as a sintering aid to densify titanium diboride (TiB₂) at a lower sintering temperature (<1700°C). The hot-pressing experiments were conducted in the temperature range of 1400°–1650°C for 1 h in an argon atmosphere and TiSi₂ addition to TiB₂ was restricted up to 10 wt%, with an overall objective to densify the materials with a fine microstructure as well as to assess the feasibility of enhancing the mechanical and electrical properties. When all the materials were hot pressed at 1650°C, the hot-pressed TiB₂– X % TiSi₂ ( X =0, 2.5, 5, 10 wt%) composites were found to be densified to more than 98%ρ_th (theoretical density), except monolithic TiB₂ (∼94%ρ_th). An interesting observation is the formation of a Ti₅Si₃ phase and this phase formation is described by thermodynamically feasible sintering reactions. Our experimental results suggest that the optimal TiB₂–5 wt% TiSi₂ composite can exhibit an excellent combination of properties, including a high hardness of 25 GPa, an elastic modulus of 518 GPa, an indentation toughness of ∼6 MPa·m^1/2, a four-point flexural strength of more than 400 MPa, and an electrical resistivity of 10 μΩ·cm.     

Elastic Properties and Microcracking Behavior of Particulate Titanium Diboride–Silicon Carbide Composites

The spontaneous microcracking of particulate TiB₂–SiC composites is studied as a function of TiB₂ volume fraction. The degree of microcracking was examined by measuring elastic properties from room temperature to 1300°C. The results showed that only one composition contains microcracks. All other compositions did not microcrack regardless of TiB₂ volume fraction. This was attributed to the difference in the sintering aids. In particular, the Al₂O₃ sintering aid needed in these compositions had reacted with SiO₂ to form an amorphous grain boundary phase that allowed residual stresses to relax by viscous flow at moderate to high temperatures. The existence of this amorphous grain boundary phase was directly observed by transmission electron microscopy.     

Microstructure and Mechanical Properties of In Situ Produced TiC/TiB2/MoSi2 Composites

A novel microstructure of in situ produced TiC/TiB₂/MoSi₂ composite and its mechanical properties were investigated. The results indicate that TiC/TiB₂/MoSi₂ composites can be fabricated by reactive hot pressing the mixed powders of MoSi₂, B₄C, and Ti. A novel microstructure consisting of hollow particles of TiC and TiB₂ grains in an MoSi₂ matrix was obtained. Grains of in situ produced TiC and TiB₂ were much finer, from 100 to 400 nm. During the fracture process, hollow particles relieved crack tip stress, encouraging crack branching and changing the original direction of the main crack. The highest bending strength of this composite achieved was 480 MPa, twice that of monolithic MoSi₂, and the greatest fracture toughness of the composite reached 5.2 MPa·m^1/2.     

Pressureless Sintering of Dense Si3N4 and Si3N4/SiC Composites with Nitrate Additives

The effect of aluminum and yttrium nitrate additives on the densification of monolithic Si₃N₄ and a Si₃N₄/SiC composite by pressureless sintering was compared with that of oxide additives. The surfaces of Si₃N₄ particles milled with aluminum and yttrium nitrates, which were added as methanol solutions, were coated with a different layer containing Al and Y from that of Si₃N₄ particles milled with oxide additives. Monolithic Si₃N₄ could be sintered to 94% of theoretical density (TD) at 1500°C with nitrate additives. The sintering temperature was about 100°C lower than the case with oxide additives. After pressureless sintering at 1750°C for 2 h in N₂, the bulk density of a Si₃N₄/20 wt% SiC composite reached 95% TD with nitrate additives.     

In Situ Synthesis of Ultrafine ZrB2–SiC Composite Powders and the Pressureless Sintering Behaviors

Ultrafine ZrB₂–SiC composite powders have been synthesized in situ using carbothermal reduction reactions via the sol–gel method at 1500°C for 1 h. The powders synthesized had a relatively smaller average crystallite size (<200 nm), a larger specific surface area (∼20 m²/g), and a lower oxygen content (∼1.0 wt %). Composites of ZrB₂+20 wt% SiC were pressureless sintered to ∼96.6% theoretical density at 2250°C for 2 h under an argon atmosphere using B₄C and Mo as sintering aids. Vickers hardness and flexural strength of the sintered ceramic composites were 13.9±0.3 GPa and 294±14 MPa, respectively. The microstructure of the composites revealed that elongated SiC grain dispersed uniformly in the ZrB₂ matrix. Oxidation from 1100° to 1600°C for 30 min showed no decrease in strength below 1400°C but considerable decrease in strength with a rapid weight increment was observed above 1500°C. The formation of a protective borosilicate glassy coating appeared at 1400°C and was gradually destroyed in the form of bubble at higher temperatures.     

Toughening of SiC with Ti3SiC2 Particles

Composites in the SiC–TiC–Ti₃SiC₂ system were synthesized using reactive hot pressing at 1600°C. The results indicate that addition of Ti₃SiC₂ to SiC leads to improved fracture toughness. In addition, high microhardness can be retained if TiC is added to the material. The best combination of properties obtained in this study is K _{I c} =8.3 MPa·m^1/2 and H _v=17.6 GPa. The composition can be tailored in situ using the decomposition of Ti₃SiC₂. Ti₃SiC₂ decomposed rapidly at temperatures above 1800°C, but the decomposition could be conducted in a controlled manner at 1750°C. This can be used for synthesis of fully dense composites with improved properties by first consolidating to full density a softer Ti₃SiC₂-rich initial composition, and then using controlled decomposition of Ti₃SiC₂ to achieve the desired combination of microhardness and fracture toughness.     

Synthesis, Properties, and Oxidation of Alumina-Titanium Nitride Composites

Al₂O₃-TiN composites varying from 60 to 66.6 mol% TiN were prepared by an in situ reaction between TiO₂ and AlN. N₂ or O₂ evolution takes place, depending on the composition selected. A pseudobrookite (PB) phase appears in the reaction product, the amount decreasing as the TiO₂:AlN ratio becomes poor in AlN. The in situ reaction product can be pressureless sintered to 94% to 97% theoretical density at 1600°C in N₂. The four-point flexural strength varies from 280 to 430 MPa at room temperature. The fracture toughness is 3 to 4.7 MPa.m^1/2. Oxidation of a 94% dense TiN-Al₂O₃ composite in the temperature range 710° to 1050°C was also studied. A layer of TiO₂ (rutile) protects the composite at 710°C from further oxidation with a weight gain of 0.08 mg/cm² in 90 min. In the temperature range 820° to 1050°C, the initial oxidation kinetics are parabolic, with an activation energy of 216.5 kJ/mol. Linear oxidation kinetics with an activation energy of 113.7 kJ/mol pertain at longer times.     

Mechanical Properties and Fracture Toughness of α-Al2O3-Platelet-Reinforced Y-PSZ Composites at Room and High Temperatures

YPSZ/Al₂O₃-platelet composites were fabricated by conventional and tape-casting techniques followed by sintering and HIPing. The room-temperature fracture toughness increased, from 4.9 MPa·m^1/2 for YPSZ, to 7.9 MPa·m^1/2 (by the ISB method) for 25 mol% Al₂O₃ platelets with aspect ratio = 12. The room-temperature fiexural strength decreased 21% and 30% (from 935 MPa for YPSZ) for platelet contents of 25 vol% and 40 vol%, respectively. Al₂O₃ platelets improved the high-temperature strength (by 110% over YPSZ with 25 vol% platelets at 800°C and by 40% with 40 vol% platelets at 1300°C) and fracture toughness (by 90% at 800°C and 61% at 1300°C with 40 vol% platelets). An amorphous phase at the Al₂O₃-platelet/YPSZ interface limited mechanical property improvement at 1300°C. The influence of platelet alignment was examined by tape casting and laminating the composites. Platelet alignment improved the sintered density by >1% d _th , high-temperature strength by 11% at 800°C and 16% at 1300°C, and fracture toughness by 33% at 1300°C, over random platelet orientation.     

Effect of Hot-Pressing Temperature on Densification and Mechanical Properties of Titanium Diboride with Silicon Nitride as a Sintering Aid

The effect of hot-pressing temperature on the densification behavior and mechanical properties of titanium diboride (TiB₂) was investigated. TiB₂ specimens were hot-pressed for 1 h at temperatures in the range of 1500°–1800°C, with an addition of 2.5 wt% of silicon nitride (Si₃N₄) as a sintering aid. The density increased markedly at temperatures in the range of 1500°–1600°C and remained constant thereafter. The formation of a eutectic liquid at 1550°C was attributed to the steep increase in density. The hot-pressing temperature also improved the mechanical properties, such as the flexural strength, Vickers hardness, and fracture toughness of the specimens. Similar to the density, the mechanical properties improved remarkably at ∼1550°C, so that optimum properties were obtainable at temperatures as low as 1600°C.     

Effects of α-Sic versus β-Sic Starting Powders on Microstructure and Fracture Toughness of Sic Sintered with Al2O3-Y2O3 Additives

Dense Sic ceramics were obtained by pressureless sintering of β-Sic and α-Sic powders as starting materials using Al₂O₃-Y₂O₃ additives. The resulting microstructure depended highly on the polytypes of the starting SiC powders. The microstructure of SiC obtained from α-SiC powder was composed of equiaxed grains, whereas SiC obtained from α-SiC powder was composed of a platelike grain structure resulting from the grain growth associated with the β→α phase transformation of SiC during sintering. The fracture toughness for the sintered SiC using α-SiC powder increased slightly from 4.4 to 5.7 MPa.m^1/2 with holding time, that is, increased grain size. In the case of the sintered SiC using β-SiC powder, fracture toughness increased significantly from 4.5 to 8.3 MPa.m^1/2 with holding time. This improved fracture toughness was attributed to crack bridging and crack deflection by the platelike grains.     

Densification of Si3N4 with LiYO2 Additive

This paper deals with the densification and phase transformation during pressureless sintering of Si₃N₄ with LiYO₂ as the sintering additive. The dilatometric shrinkage data show that the first Li₂O- rich liquid forms as low as 1250°C, resulting in a significant reduction of sintering temperature. On sintering at 1500°C the bulk density increases to more than 90% of the theoretical density with only minor phase transformation from α-Si₃N₄ to β-Si₃N₄ taking place. At 1600°C the secondary phase has been completely converted into a glassy phase and total conversion of α-Si₃N₄ to β-Si₃N₄ takes place. The grain growth is anisotropic, leading to a microstructure which has potential for enhanced fracture toughness. Li₂O evaporates during sintering. Thus, the liquid phase is transient and the final material might have promising mechanical properties as well as promising high-temperature properties despite the low sintering temperature. The results show that the Li₂O−Y₂O₃ system can provide very effective low-temperature sintering additives for silicon nitride.     

Effect of Cr3C2 Addition on the Sintering of SiC-TiC Composite

The densification behavior and mechanical properties of SiC-30TiC (in volume percent) composites prepared with Cr₃C₂ additive were investigated. By hot-pressing a SiC-30TiC-lCr₃C₂ specimen at 1950°C, 98.5% of theoretical density was achieved and the specimen exhibited a fracture strength of 750 MPa. For the SiC-30TiC-10Cr₃C₂ specimen, (β-α transformation of SiC was observed to occur during hot-pressing and in situ growth of elongated α-SiC grains resulted in an increase of fracture toughness. Micro-structural observations using high-resolution TEM indi-cated that no liquid phase was present at the interfaces.