Ti(C,N)基金属陶瓷/AgCuTi/40Cr钎焊接头组织和机械性能研究

在真空钎焊炉中采用活性钎料AgCuTi,成功将Ti(C,N)基金属陶瓷和金属40Cr进行钎焊连接,形成了Ti(C,N)基金属陶瓷/AgCuTi/40Cr钎焊接头.采用SEM、EDS和XRD等手段对Ti(C,N)基金属陶瓷/AgCuTi/40Cr钎焊接头的形貌组织进行了分析,研究了钎焊接头的机械性能,得到了Ti(C,N)...     

BNi-2钎焊1Cr18Ni9Ti工艺的研究

采用钎焊接头楔形间隙图,对BNi-2钎料钎焊1crl8Ni9Ti的最大钎焊间隙进行分析,考察BNi-2钎料钎焊1Cr18Ni9Ti的钎焊工艺及钎焊后扩散热处理工艺对最大钎焊间隙的影响.实验结果得出,BNi-2钎焊1Cr18Ni9Ti的最佳钎焊温度为1150℃,保温时间为55 min;钎焊后合适的扩散热处理温度为:1000℃,保温时间为60～90 min.     

SiC陶瓷真空钎焊接头的组织及性能分析

采用BNi-5钎料对SiC陶瓷进行真空钎焊,获得了力学性能良好的SiC钎焊接头,并对焊缝的微观结构和形成过程进行了分析。研究结果表明,Ni基钎料与SiC母材发生反应生成层状界面反应层结构,所形成的SiC钎焊接头钎缝微观形貌可以表述为:SiC母材/石墨+Ni_2Si/Ni_2Si/石墨+Ni_2Si/Cr_3Ni_2SiC/Ni+Cr_3Ni_5Si_2/Cr_3Ni_2SiC/石墨+Ni_2Si/Ni_2Si/石墨+Ni_2Si/SiC母材。所得SiC钎焊接头常温力学性能较好,平均钎焊接头剪切强度可达到124 MPa。Ni基钎料钎焊SiC陶瓷接头的断裂位置位于钎料与陶瓷基体间的界面反应层,主要原因是界面反应层中Ni_2Si和Cr_3Ni_2SiC等脆性化合物在钎焊接头拉伸变形过程中会产生应力集中,在残余钎焊应力的共同作用下钎焊接头发生断裂。     

SiC颗粒增强铝基复合材料的钎焊性

采用氩气保护炉中钎焊和真空钎焊两种试验方法,对SiCp/101Al复合材料的钎焊性进行研究。结果表明,通过选择合理的钎料和钎剂及采用正确的钎焊工艺参数,可以实现对SiCp/101Al复合材料的钎焊连接。对获得接头进行力学性能测试,表明钎焊接头的剪切强度随钎焊温度的升高而升高,当达到一定值以后,又随着钎焊温度的升高而降低。对接头钎缝区的XRD相结构分析中发现,接头中含有Al-Cu、Al-Si共晶组织相,并且有SiC相存在,说明母材中有部分SiC增强相颗粒过渡到了钎缝之中,有利于提高钎缝接头的力学性能。从钎焊接头的断口扫描照片中可以看出,接头大部分都呈韧性断裂特征,且大多数接头都断裂于靠近钎缝的母材部位,说明钎焊接头的质量较高,钎焊工艺可行。     

CuMnNiCo钎料钎焊MGH956合金接头组织及力学性能研究

采用自制的CuMnNiCo钎料对氧化物弥散强化(ODS)合金MGH956进行钎焊实验,分析了钎焊过程中各种组织的形成过程,研究了不同的钎焊温度对接头组织和性能的影响。结果表明:在1000~1050℃保温20min工艺下钎焊MGH956合金,均可获得良好的钎焊成形效果,钎焊接头由钎缝中心区的Cu-Mn基固溶体和两侧扩散反应区的Fe-Mn基固溶体组成,并含有三种不同的化合物相。钎焊温度为1030℃和1050℃时,接头的室温拉伸断裂发生在钎缝中心处,断口主要呈沿晶脆性断裂特征。钎焊温度的提高使沿晶界分布的脆性(Mn,Ni)-Si相减少,有利于改善钎焊接头强度,钎焊接头的室温抗拉强度最高可达到母材强度的75%。     

温度对Cu颗粒增强复合钎料蠕变性能的影响

蠕变性能是影响钎焊接头可靠性的重要指标之一.采用搭接面积为1 mm2的单搭接钎焊接头,在恒定载荷下,测定了Cu颗粒增强锡铅基复合钎料钎焊接头的蠕变寿命,分析并讨论了温度对该复合钎料蠕变寿命的影响.结果表明:Cu颗粒增强的锡铅基复合钎料的蠕变抗力优于传统63Sn37Pb共晶钎料;钎焊接头蠕变寿命随温度的升高而降低,并且温度对复合钎料钎焊接头蠕变寿命的影响较传统63Sn37Pb钎料明显.     

铝基钎料在SiC及SiC_p/6061复合材料上的润湿性研究

对多种铝基钎料在SiC、6 0 6 1及SiCp 6 0 6 1复合材料上进行了润湿性试验。结果表明 :炉中钎焊时 ,钎料与钎剂的成分、加热温度与保温时间、钎料与钎剂熔化温度的匹配等是影响铝基钎料润湿性的主要因素 ;真空钎焊时 ,镁含量不同的各种含镁Al 2 8Cu 5Si钎料在Al基复合材料连接的温度范围内都不能润湿SiC陶瓷表面 ;配合QJ2 0 1钎剂 ,Al 2 8Cu 5Si 2Mg钎料对 15 %SiCp 6 0 6 1Al复合材料具有良好的润湿性 ,但对 30 %SiCp 6 0 6 1Al复合材料却润湿不良 ;在加钎剂的情况下 ,钎料中的镁反而对在铝合金及铝基复合材料上的润湿性有不利影响 ;在Al 2 8Cu 5Si 2Mg钎料和 15 %SiCp 6 0 6 1Al复合材料的钎焊界面处存在SiC颗粒的偏聚现象     

Cu-P-Sn-Ni钎料真空钎焊MGH956合金的研究

为扩展Cu-P基钎料在连接MGH956合金中的应用,采用新型Cu-P-Sn-Ni钎料对MGH956合金在800~890℃进行了真空钎焊,研究了不同钎焊温度和保温时间对焊缝组织及力学性能的影响.结果表明:在所研究的钎焊温度范围内保温5 min均可获得成形效果良好的钎焊接头,其主要由钎缝中心区和界面反应层组成,其中,钎缝中心区由α(Cu)固溶体基体和化合物Cu_3P+(Fe,Ni)_3P+FeCr组成,反应层由α(Fe)固溶体、Fe_3P和Cu_3P组成;随着钎焊温度的升高,反应层厚度逐渐增加,钎缝中心区中的化合物Cu_3P+(Fe,Ni)_3P+FeCr的形态也随之发生明显改变;各钎焊温度下获得的钎焊接头经室温拉伸,断裂均发生在钎缝中心区,断口形貌呈现韧性和脆性的混合断裂特征.830℃钎焊5 min的接头抗拉强度最大,为510.3 MPa,达到了母材抗拉强度的70.9%.     

Al-Si-Cu-Zn钎料钎焊3003铝合金的接头组织及力学性能

采用自制的Al-Si-Cu-Zn钎料对3003铝合金进行钎焊实验,利用X射线衍射、扫描电镜、能谱仪对接头微观组织和断口进行分析,并研究了钎焊温度对接头组织和性能的影响。结果表明:在540~580℃保温10min工艺下钎焊3003铝合金,均可获得良好的钎焊效果。钎焊接头均由钎缝中心区的α(Al)固溶体、θ(Al2Cu)金属间化合物、细小Si相和AlCuFeMn+Si相,两侧扩散区的α(Al)固溶体与元素扩散层以及母材组成;钎焊接头室温剪切断裂于扩散区齿状α(Al)/钎缝中心区的交界面,断口主要呈脆性解理断裂特征。随着钎焊温度的升高,扩散区的α(Al)固溶体晶粒长大,接头结合界面犬牙交错;当钎焊温度为560℃,保温10min时,接头的室温抗剪强度达到最大值92.3MPa,约为母材强度的62.7%。     

应力对Ag颗粒增强SnCu基复合钎料蠕变性能的影响

使用搭接面积为1mm2的单搭接钎焊接头,研究了恒定温度下应力对Ag颗粒增强SnCu基复合钎料钎焊接头蠕变寿命的影响,结果表明:Ag颗粒增强SnCu基复合钎料的蠕变抗力优于99.3Sn0.7Cu基体钎料;随着应力的增大,复合钎料及其基体钎料钎焊接头的蠕变寿命均呈下降趋势,且应力对复合钎料钎焊接头蠕变寿命的影响比基体钎料明显.     

Brazing of 422 stainless steel using the AWS classification BNi-2 Braze alloy

The study of brazing 422 stainless steel (422SS) using the AWS classification BNi-2 braze alloy as the filler metal is evaluated in the study. The BNi-2 braze alloy demonstrates excellent wettability on the 422SS substrate for temperatures exceeding 1025 °C. The brazed joint is primarily comprised of the Ni-rich matrix and chromium boride. Additionally, the B–Cr–Fe precipitates are formed at the interface between the braze and 422SS. Some Kirkendall porosity is also observed in the braze close to the interface, due to nonsymmetrical interdiffusion between the braze and 422SS substrate. Shear strengths of brazed joints are varied from 306 to 481 MPa. The infrared brazed specimen shows the highest shear strength among all brazed specimens. Increasing brazing temperature and/or time result in decreased shear strength of the brazed joint.     

Intermetallic compounds formed during brazing of titanium with aluminium filler metals

The effect of aluminium filler metal composition on the formation of AI-Ti intermetallic compounds was investigated in brazed aluminium-to-titanium (Al/Ti) joints and titanium-totitanium (Ti/Ti) joints. The clearance filling ability was also studied. In Ti/Ti joints, the thickness of the intermetallic compound layer was strongly dependent on the aluminium filler metal composition, whereas the clearance filling ability was independent of the composition. The maximum intermetallic compound layer thickness was observed in 99.99% highly pure aluminium filler metal; therefore all additional elements reduced the layer thickness. Above all, the addition of 0.8% Si greatly reduced the thickness. After brazing at 680° C for 3 min, the intermetallic compound formed by Al-0 to 0.8% Si filler metal was found to be of type Al₃Ti. Other compounds, of types Ti₉Al₂₃ and Ti₇Al₅Si₁₂, were also found in joints brazed by Al-3 to 10% Si filler metals. AI-0.8% Si filler metals maintained a higher joint strength than pure aluminium filler metal under brazing conditions of high temperature and long heating time. In Al/Ti joints, AI-Cu-Sn and AI-Cu-Ag filler metal mainly formed Al₃Ti, and Al-10Si-Mg filler metal mainly formed Ti₇Al₅Si₁₂ at the brazed interface of the titanium side after brazing at 600 to 620° C.     

Microstructure and strength of brazed joints of Ti3Al-base alloy with different filler metals

The interfacial microstructure and properties of brazed joints of a Ti₃Al-based alloy were investigated in this paper to meet the requirements of the use of Ti₃Al-based alloy in the aeronautic and space industries. The effects of different brazing fillers on the interfacial microstructure and shear strength were studied. The relationship between brazing parameters and shear strength of the joints was discussed, and the optimum brazing parameters were obtained. The brazed joints were qualitatively and quantitatively analyzed by means of EPMA, SEM and XRD. The results showed that using a AgCuZn brazing filler, TiCu, Ti(Cu,Al)₂ and Ag[s,s] were formed, the shear strength of the joint was decreased because of the formation of TiCu and Ti(Cu,Al)₂; using a CuP brazing filler, Cu₃P, TiCu and Cu[s,s] were formed at the interface of the joint, the former two intermetallic compounds decreased the shear strength. The analysis also indicated that using the TiZrNiCu brazing filler, the optimum parameters were temperature T=1323 K, joining time t=5 min, and the maximum shear strength was 259.6 MPa. For the AgCuZn brazing filler, the optimum parameters were joining temperature T=1073 K, joining time t=5 min, and the maximum shear strength was 165.4 MPa. To the CuP brazing filler, the optimum parameters were joining temperature T=1223 K, joining time t=5 min, and the maximum shear strength is 98.6 MPa. Consulting the results of P. He, J.C. Feng and H. Zhou [Microstructure and strength of brazed joints of Ti₃Al-base alloy with NiCrSiB, Mater. Charact., 52(8) (2004) 309–318], relative to the other brazing fillers, TiZrNiCu is the optimum brazing filler for brazing Ti₃Al-based alloy.     

Vacuum brazing of GH99 superalloy using graphene reinforced BNi-2 composite filler

A novel graphene reinforced BNi-2 composite filler was developed for brazing GH99 superalloy. The interfacial microstructure of brazed joints was analyzed by field emission scanning electron microscope and a transmission electron microscope. The effects of graphene addition on the microstructure evolution and mechanical properties of brazed joints were investigated, and the strengthening mechanism of graphene was analyzed. The results revealed that due to the addition of graphene, M₂₃(C,B)₆ compounds were synthesized in the γ solid solution and brittle boride precipitates near the brazing seam decreased. Graphene was effective in retarding solute atoms diffusion thus impeding the precipitation of borides. Furthermore, the low coefficient of thermal expansion (CTE) of graphene was conducive to relieve stress concentration of the brazed joints during the cooling process. The shear strengths of brazed joints were significantly improved by exerting the strengthening effect of graphene. The maximum shear strengths of the brazed joints were 410.4?MPa and 329.7?MPa at room temperature and 800?°C, respectively.     

Interfacial microstructure and strength of brazed copper/porous copper foam towards the effect of porous copper foam pore density and brazing holding time

The porous copper foam was sandwiched between two coppers plate and then brazed using copper-tin (9.7 %)-nickel (5.7 %)-phosphorus (7 %) filler foil. Brazing process was conducted to joint copper/porous copper foam by evaluating the effect of porous copper foam pore densities [pore per inch (PPI)] and brazing holding times. The brazed joint interface of copper and porous copper foam was characterised using Field emission scanning electron microscopy and Energy-dispersive x-ray spectroscopy for the microstructure and elemental composition analysis, respectively. X-ray diffraction analysis was carried out on the shear fractured surfaces of brazed copper and porous copper foam for phase determination. The results exhibited distinct phases of copper (Cu), copper phosphide (Cu₃P), nickel phosphide (Ni₃P), and copper compound with tin (6 : 5) (Cu₆Sn₅). The filler layer was formed as an island-shaped that consists of copper phosphide and nickel phosphide. Prolong brazing holding time causes a thinner filler layer in brazing seam. While the non-uniform thickness of the filler layer was observed at different pore densities of porous copper foam. The shear strength of brazed copper/porous copper foam 15 PPI with a 10 min brazing holding time yield a maximum shear strength of 2.9 MPa.     

Ni－Cr－Co－B钎料钎焊K3合金接头组织研究

采用金相分析、电子探针及Ｘ射线衍射等试验手段确定了Ｎｉ－Ｃｒ－Ｃｏ－Ｂ钎料及其钎焊的Ｋ３合金接头的相组成，研究了钎焊工艺参数和焊后扩散热处理对这类接头组织的影响，并与ＢＮｉ－ｌａ钎料钎焊的Ｋ３合金接头进行了对比。对采用Ｎｉ－Ｃｒ－Ｃｏ－Ｂ钎料和ＢＮｉ－ｌａ钎料钎焊的Ｋ３合金接头室温冲击韧性进行了对比评定。     

Ni-Cr-P焊膏钎焊C/C复合材料的组织和性能

用真空熔炼、惰性气体雾化法制备Ni-Cr-P金属粉末,再加入有机黏结剂高速搅拌,制备Ni14Cr10P膏状活性钎料。用制备好的焊膏真空钎焊C/C复合材料,测试钎焊接头的剪切强度,通过OM,SEM,EDS,XRD等对钎焊接头界面组织结构进行分析。结果表明:在钎焊温度1000℃、保温时间0.5 h条件下,获得的接头剪切强度达到28.6 MPa,然后随着钎焊温度上升或保温时间延长,钎焊接头强度下降;通过界面组织结构分析发现焊膏可以增加钎料层与C/C复合材料表面的接触面积,有利于堵塞C/C复合材料表面的孔隙。焊后在界面处形成了交错分布的Cr碳化物相缓冲层,使得界面呈现热膨胀系数梯度增加的结构,有助于缓解热失配,提高C/C复合材料钎焊接头强度。     

采用银基活性钎料钎焊碳/碳复合材料

采用银基活性钎料（Ag-Cu-Ti）对二维层间增强型和三维正交增强型C/C复合材料进行了真空钎焊工艺试验，采用扫描电镜（SEM）观察了钎焊接头和连接界面的微观组织形貌，测定了各元素的面分布，对钎焊接头进行了室温压缩剪切性能试验和三点弯曲强度试验。结果表明：钎料中的元素Ti向钎料和C/C界面区扩散并富集，生成了含元素C的Ti2Cu化合物相，形成了钎料对C/C基体的良好润湿，可获得组织致密的接头，接头室温三点弯曲强度为：39MPa，抗剪强度为22MPa。     

Joining of C/C composite to TC4 using SiC particle-reinforced brazing alloy

Silicon carbide particles were used as reinforcement in the Ag-26.7Cu-4.6Ti (wt.%) brazing alloy for joining C/C composite to TC4 (Ti-6Al-4V, wt.%). The mechanical properties of the brazed joints were measured by shear strength testing. The effects of the volume percentage of SiC particles on the microstructures of the brazed joints were investigated. It is shown that the maximum shear strength of the joints is 29 MPa using 15 vol.% SiC in the brazing alloy which is greater than that with Ag-26.7Cu-4.6Ti brazing alloy alone (22 MPa). Ti is reacted with SiC particles, forming Ti–Si–C compound in the particle-reinforced brazing alloy. Due to this, more SiC particles in the brazing alloy, the thickness of TiC/TiCu reaction layer near C/C composite decreases. Moreover, SiC particles added to the brazing alloy can reduce the CTE of the brazing alloy which results in lower residual stress in the C/C composite-to-metal joint. Both of the above reasons lead to the increasing of the shear strength of the brazed joints. But excessive SiC particles added to the brazing alloy lead to pores which results in poor strength of the brazed joint.     

Effects of Al_2O_3-Particulate-Contained Composite Filler Materials on the Shear Strength Alumina Joints

Al2O3l2O3 joints were brazed with a new kind of filler materials, which were formed by adding AI203 particulates into Ag-Cu-Ti active filler metal. The results showed that the material parameters (the Ti content, Al2O3 particulate volume fraction) of the composite filler materials affected the shear strength of brazed joints. When the Ti content was 2 wt pct in the filler metal, the shear strength of brazing joints decreased with the increasing the volume ratio of Al2O3 particulate. When the Ti content was 3 wt pct in the filler metal, the shear strength of joints increased from 93.75 MPa(AI203p 0 vol. pct) to 135.32 MPa(AI203p 15 vol. pct).