Co3+掺杂LaFeO3的制备及光催化降解硝基苯的性能研究

以La(NO3)3、Fe(NO3)3.9H2O和Co(NO3)2.6H2O为原料,采用柠檬酸络合法制备了纯LaFeO3和掺杂Co3+的LaFeO3纳米粉体,通过XRD和SEM等手段对样品进行表征,以硝基苯为目标降解物,考察催化剂的光催化降解活性。研究表明:煅烧温度为800℃时制备的LaFeO3样品对硝基苯溶液的脱色率达47.02%;而采用Co3+的掺杂增强了LaFeO3的光吸收特性,对LaFeO3的光催化性能有较大促进作用,且掺杂量为5%时效果最好,光降解时间1h时,对硝基苯的降解率可达76.26%。     

Doping effects of Co(2+) ions on ZnO nanorods and their photocatalytic properties

A series of Zn(1-x)Co(x)O nanorods with dopant content ranging from x = 0.00 to 0.10 was prepared by a wet chemical method. All Zn(1-x)Co(x)O samples were investigated by x-ray diffraction, transmission electron microscopy, energy-dispersion x-ray line mapping analysis, and UV-visible absorption spectroscopy. It was found that Co(2+) ions were homogeneously substituted for Zn(2+) ions in ZnO nanorods. Rhodamine B degradation was used as a probe reaction to evaluate the effect of Co(2+) doping on ZnO nanorods and photocatalytic performance under UV light and visible light irradiation. Co(2+) ions acted as the trapping or recombination centers for electrons and holes, leading to a reduction in photodegradation efficiency under UV light illumination. Alternatively, Co(2+) ions enhanced the optical absorption and produced the photoinduced carriers under visible illumination in terms of two charge transfer transitions involving Co(2+) ions. Consequently, Co(2+) ions substituted in the lattice of ZnO nanorods significantly improved the visible light photocatalytic activity.     

Photocatalytic degradation of azo dyes using Au:TiO2, gamma-Fe2O3:TiO2 functional nanosystems

We report photocatalytic degradation studies on Navy Blue HE2R (NB) dye on significant details as a representative from the class of azo dyes using functional nanosystems specifically designed to allow a strong photocatalytic activity. A modified sol-gel route was employed to synthesize Au and gamma-Fe2O3 modified TiO2 nanoparticles (NPs) at low temperature. The attachment strategy is better because it allows clear surface of TiO2 to remain open for photo-catalysis. X-ray diffraction, Raman and UV-VIS spectroscopy studies showed the presence of gold and iron oxide phases along-with the anatase TiO2 phase. TEM studies showed TiO2 nanocomposite particles of size approximately 10-12 nm. A detailed investigation on heterogeneous photocatalytic performance for Navy Blue HE2R dye was done using the as-synthesized catalysts Au:TiO2 and gamma-Fe2O3:TiO2 in aqueous suspension under 8 W low-pressure mercury vapour lamp irradiation. Also, the photocatalytic degradation of Amranth and Orange G azo dyes were studied. The surface modified TiO2 NPs showed significantly improved photocatalytic activity as compared to pure TiO2. Exposure of the dye to the UV light in the presence of pure and gold NPs attached TiO2 catalysts caused dye degradation of about approximately 20% and approximately 80%, respectively, in the first couple of hours. In the presence of gamma-Fe2O3 NPs attached TiO2, a remarkable approximately 95% degradation of the azo dye was observed only in the first 15 min of UV exposure. The process parameters for the optimum catalytic activity are established which lead to a complete decoloration and substantial dye degradation, supported by the values of the Chemical Oxygen Demand (COD) approximately 93% and Total Organic Carbon (TOC) approximately 65% of the treated dye solution after 5 hours on the employment of the UV/Au:TiO2/H2O2 photocatalytic process.     

纳米复合材料Ag@TiO2@SiO2的制备、光催化及其抑菌性能

以SiO₂为模板, 采用溶胶-凝胶法合成核壳TiO₂@SiO₂复合材料, 用光沉积法在TiO₂@SiO₂表面沉积贵金属Ag合成核壳纳米Ag@TiO₂@SiO₂复合材料。采用透射电镜、X射线衍射、X射线光电子能谱和紫外-可见漫反射光谱进行表征。用罗丹明为目标污染物研究复合材料的光催化性能, 测试对金黄色葡萄球菌和大肠杆菌的抑菌性能。结果表明, 复合材料Ag@TiO₂@SiO₂在紫外光的照射下具有较高的催化性能, 且当含银浓度为0.6 mg/mL时, 复合材料对金黄色葡萄球菌抑菌率为93.41%, 对大肠杆菌的抑菌率为97.37%。Ag@TiO₂@SiO₂具有良好的催化性能和抑菌性能, 有望应用于水处理和医疗器械等领域。     

Synthesis,characterisation and antimicrobial activity of manganese- and iron-doped zinc oxide nanoparticles

The present work reports study on antimicrobial activity of pure and doped ZnO nanocomposites. Polyvinyl pyrrolidone capped Mn- and Fe-doped ZnO nanocomposites were synthesised using simple chemical co-precipitation technique. The synthesised materials were characterised using transmission electron microscope (TEM), X-ray powder diffraction (XRD), energy dispersive X-ray fluorescence (EDXRF), Fourier transform infrared (FTIR) spectroscopy and ultraviolet (UV) visible spectroscopy. The XRD and TEM studies reveal that the synthesised ZnO nanocrystals have a hexagonal wurtzite structure with average crystalline size ～7–14 nm. EDXRF and FTIR study confirmed the doping and the incorporation of impurity in ZnO nanostructure. The antimicrobial activities of nanoparticles (NPs) were studied against fungi, gram-positive and gram-negative bacteria using the standard disc diffusion method. The photocatalytic activities of prepared NPs were evaluated by degradation of methylene blue dye in aqueous solution under UV light irradiation. Experimental results demonstrated that ZnO NPs doped with 10% of Mn and Fe ions showed maximum antimicrobial and photodegradation efficiency in contrast with that of the 1% loading. The enhancement in antimicrobial effect and photocatalytic degradation is attributed to the generation of reactive oxygen species due to the synergistic effects of Mn and Fe loading.     

Preparation, electrocatalytic and photocatalytic performances of nanoscaled CuO/Co3O4 composite oxides

Cu-Co composite oxides with different Cu/Co atomic ratios were prepared by the calcination of the precursors synthesized via a co-precipitation method. The samples were characterized by XRD, SEM and TEM, respectively. The XRD analysis revealed that only spinel structure of Cu-Co composite oxide was confirmed with lower Cu/Co ratio (<1:2). The sizes and morphologies of samples are controlled significantly by the Cu/Co atomic ratios. The electrocatalytic activity for p-nitrophenol reduction in a basic solution with the samples decorated on glassy carbon (GC) electrodes was tested by cyclic voltammetry (CV). The results showed that the sample with Cu/Co ratio of 2:8 exhibited the highest catalytic activity for p-nitrophenol reduction. The photocatalytic performances of the samples for the degradation of methyl orange under irradiation of visible light were investigated. The samples with Cu/Co ratios from 5:5 to 10:0 all showed better photocatalytic activities for methyl orange degradation, but the sample with Cu/Co ratio of 9:1 exhibited much higher catalytic activity. The catalyst with Cu/Co ratio of 9:1 also exhibited excellent repeatability for the catalytic degradation of methyl orange.     

Synthesis,structural and optical properties of CdS nanoparticles with enhanced photocatalytic activities by photodegradation of organic dye molecules

CdS nanoparticles (NPs) were synthesized using co-precipitation method. X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to confirm the structures and morphologies of CdS NPs. X-ray diffraction data confirmed the crystal structure of the CdS NPs. Raman spectrum exhibited the Raman modes of LO and 2LO of CdS at 290 and 595 cm^?1 respectively. The evaluated band gap was 3.15 eV, this value was shifted compared with the bulk value and this could be a significance of a size quantization effect in the sample. The CdS nanoparticles showed higher photocatalytic activity for the discoloration of methyl orange (MO) under UV light irradiation for 90 min. The highest photocatalytic activity was obtained with the sample containing 0.3 wt % CdS nanoparticles, in which more than 98 % of the MO was discolored within 90 min.     

Co-Doped ZnO Nanoparticles:Structural,Morphological,Optical,Magnetic and Antibacterial Studies

Un-doped and Co-doped ZnO nanoparticles （NPs） with different weight ratios （0.5, 1.0, 1.5, and 2.0 wt% of Co） were synthesized by a facile and rapid microwave-assisted combustion method using urea as a fuel. The prepared NPs were characterized by X-ray diffraction （XRD）, high resolution scanning electron microscopy （HR-SEM）, energy dispersive X-ray analysis （EDX）, diffuse reflectance spectroscopy （DRS）, photoluminescence （PL） spectroscopy and vibrating sample magnetometry （VSM）. XRD patterns refined by the Rietveld method indicated that Co-doped ZnO had a single pure phase with wurtzite structure suggesting that Co^2＋ ions would occupy Zn^2＋ ionic sites within the ZnO crystal lattice. Interestingly, the morphology was found to convert substantially from grains to nanoparticles with close-packed periodic array of hexagonal-like shape and then into randomly distributed spherical NPs with the variation of Co-content. The optical band gap estimated using DRS was found to be red-shifted from 3.22 eV for the un-doped ZnO NPs then decrease up to 2.88 eV with increasing Co-content. PL spectra showed a strong green emission band thus confirming the formation of pure single ZnO phase. Magnetic studies showed that Co-doped ZnO NPs exhibited room temperature ferromagnetism （RTFM） and that the saturation magnetization attained a maximum value of 2.203 × 10^-3 emu/g for the highest Co-content. The antibacterial studies performed against a set of bacterial strains showed that the 2.0 wt% Co-doped ZnO NPs possessed a greater antibacterial effect.     

In Situ Constructed Perovskite–Chalcogenide Heterojunction for Photocatalytic CO2 Reduction

Perovskite nanocrystals (PNCs) are promising candidates for solar-to-fuel conversions yet exhibit low photocatalytic activities mainly due to serious recombination of photogenerated charge carriers. Constructing heterojunction is regarded as an effective method to promote the separation of charge carriers in PNCs. However, the low interfacial quality and non-directional charge transfer in heterojunction lead to low charge transfer efficiency. Herein, a CsPbBr₃–CdZnS heterojunction is designed and prepared via an in situ hot-injection method for photocatalytic CO₂ reduction. It is found that the high-quality interface in heterojunction and anisotropic charge transfer of CdZnS nanorods (NRs) enable efficient spatial separation of charge carriers in CsPbBr₃–CdZnS heterojunction. The CsPbBr₃–CdZnS heterojunction achieves a higher CO yield (55.8 µmol g⁻¹ h⁻¹) than that of the pristine CsPbBr₃ NCs (13.9 µmol g⁻¹ h⁻¹). Furthermore, spectroscopic experiments and density functional theory (DFT) simulations further confirm that the suppressed recombination of charge carriers and lowered energy barrier for CO₂ reduction contribute to the improved photocatalytic activity of the CsPbBr₃–CdZnS heterojunction. This work demonstrates a valid method to construct high-quality heterojunction with directional charge transfer for photocatalytic CO₂ reduction. This study is expected to pave a new avenue to design perovskite–chalcogenide heterojunction.     

Synthesis and physicochemical properties of titanium(IV)- and cobalt(II)-Based photocatalytic oxide composites

We have studied the phase transitions, morphology, and photocatalytic activity of composites based on titanium(IV) and cobalt(II) oxides at Co doping levels from 0.5 to 60 wt % and heat-treatment temperatures from 80 to 1150°C. The highest photocatalytic activity under illumination in the spectral range λ ≥ 670 nm is offered by mesoporous X-ray amorphous and multiphase (X-ray amorphous phase, anatase, rutile, and CoTiO₃) nanomaterials containing 5–20 wt % Co, whereas two-phase materials (rutile + CoTiO₃) have the lowest photocatalytic activity.     

Modeling electrowinning process in an expanded bed electrode

In this paper, the photocatalytic degradation of methamidophos, an organophosphorous pesticide, was investigated in aqueous solution by using TiO(2) as a photocatalyst. The degradation was studied under different conditions such as the amount of the photocatalyst, illumination time, pH of the system, reaction temperature, initial concentration, electron acceptors, metal ions and presence of anions. The results showed that the photocatalytic degradation of methamidophos was strongly influenced by these parameters. The best conditions for the photocatalytic degradation of methamidophos were obtained. The optimum amount of the photocatalyst used is 12.0g/L. The photodegradation efficiency of methamidophos increases with the increase of the illumination time. Alkaline media are favorable for the photocatalytic degradation of methamidophos. The degradation efficiency is enhanced by increasing reaction temperature, and the photodegradation efficiency decreases with the increase in the initial concentration of methamidophos. The photodegradation efficiency of methamidophos is accelerated by adding a small amount of H(2)O(2), K(2)S(2)O(8), KBrO(3), Fe(3+) or Cu(2+). There are no obvious effects on the reactions with the addition of a small amount of Na(+), K(+), Mg(2+), Ca(2+), Zn(2+), Co(2+) and Ni(2+) or adding trace amount of SO(4)(2-), Cl(-), Br(-). The possible roles of the additives on the reactions and the possible mechanisms of effect were also discussed.     

ZnO:Cd纳米棒的制备及其光催化降解性能研究

采用水热法制备了ZnO和不同Cd掺杂浓度的ZnO:Cd纳米棒。通过x射线衍射仪、扫描电子显微镜、紫外-可见-近红外分光光度计和拉曼光谱对ZnO:Cd纳米棒的结构和光学特性进行了系统研究。结果显示,样品为一维纳米棒结构,Cd的掺杂可以减小ZnO纳米棒的晶粒尺寸和光学带隙。利用分光光度计检测ZnO:Cd纳米棒对偶氮结构染料(甲基橙溶液)的光催化降解效率,结果表明Cd掺杂可以改善ZnO的光催化性能,掺杂浓度为16%时ZnO:Cd纳米棒对甲基橙溶液的光催化降解效率最高。     

Synthesis and investigation of SnS<Subscript>2</Subscript>/RGO nanocomposites with different GO concentrations: structure and optical properties,photocatalytic performance

In this study, we report the synthesis of tin disulfide/reduced graphrene oxide (SnS₂/RGO) nanocomposites by a simple one-step hydrothermal method. In order to investigate the effect of RGO on the structure and optical properties and photocatalytic activity of the products a series of nanocomposites was prepared with different concentrations of GO. The samples were examined using X-ray diffraction, field emission scanning electron microscopy (FESEM), Raman spectroscopy, UV–Vis spectroscopy and photoluminescence techniques. The results confirmed the growth of SnS₂ with the hexagonal phase. FESEM analysis showed that the hexagonal tin disulfide nanoplates are uniformly dispersed on the surface of the graphene oxide sheets. The optical examination of SnS₂ and SnS₂/RGO nanocomposites indicated that the band gaps of all nanocomposites are greater than that of SnS₂ due to the quantum confinement effect. The photocatalytic activity of the SnS₂/RGO nanocomposites was investigated for degradation of the acid orange 7 dye under visible light. It was observed that all nanocomposites have a higher photocatalytic activity for the degradation in comparison with pure SnS₂. The optimum concentration of GO in SnS₂/RGO nanocomposite for achieving the highest photocatalytic efficiency (81%) was determined as 2 mg ml^?1 during 180 min.     

Influence of synthetic parameters on the enhanced photocatalytic properties of ZnO nanoparticles for the degradation of organic dyes: a green approach

Herein, we report a green synthetic strategy using aqueous leaves extract of Actinodaphne madraspatna Bedd (AMB) for the synthesis of ZnO NPs. The physical shape, size, thermal stability, surface area, surface composition and chemical state, morphological and optical properties of the synthesized ZnO NPs are well characterized through UV–Visible diffuse reflectance spectroscopy (DRS UV), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), Raman spectroscopy, thermal gravimetric analysis–differential thermal analysis (TGA–DTA), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET) and X-ray photon spectroscopy (XPS). FT-IR spectrum of ZnO NPs showed a characteristic peak at 416.62 cm^?1. Optical studies of prepared ZnO NPs showed the bandgap values are reduced in the range of 3.05 to 2.96 eV. The XRD and TEM data revealed the synthesized ZnO NPs exist in wurtzite crystal structure with crystallite sizes of 18 nm to 68 nm range. The variation in bandgap, surface area and crystallite structure of ZnO NPs would be achieved by changing the experimental parameters. FESEM showed spherical-shaped structure. XPS result confirmed the atomic states of Zn and O. The green synthesized ZnO NPs were examined for the photocatalytic degradation of methylene blue (MB) and acid violet 17 (AV17) dyes under UV light and the rate constants ‘k’ was calculated. It is found that the green synthesized ZnO NPs with reduced bandgap showed enhanced photocatalytic activity with higher rate constant.

     

Studies on photodegradation of two commercial dyes in aqueous phase using different photocatalysts

The present study involves the photocatalytic degradation of Methyl Orange (MO) and Rhodamine 6G (R6G), employing heterogeneous photocatalytic process. Photocatalytic activity of various semiconductors such as titanium dioxide (TiO(2)), zinc oxide (ZnO), stannic oxide (SnO(2)), zinc sulphide (ZnS) and cadmium sulphide (CdS) has been investigated. An attempt has been made to study the effect of process parameters viz., amount of catalyst, concentration of dye and pH on photocatalytic degradation of MO and R6G. The experiments were carried out by irradiating the aqueous solutions of dyes containing photocatalysts with UV and solar light. The rate of decolorization was estimated from residual concentration spectrophotometrically. Similar experiments were carried out by varying pH (2-10), amount of catalyst (0.25-2.0g/l) and initial concentration of dye (5-200mg/l). The experimental results indicated that the maximum decolorization (more than 90%) of dyes occurred with ZnO catalyst and at basic pH and the maximum adsorption of MO was noticed at pH 4 and of R6G at pH 10. The percentage reduction of MO and R6G was estimated under UV/solar system and it was found that COD reduction takes place at a faster rate under solar light as compared to UV light. In case of R6G, highest decolorizing efficiency was achieved with lower dose of catalyst (0.5g/l) than MO (1g/l) under similar conditions. The performance of photocatalytic system employing ZnO/solar light was observed to be better than ZnO/UV system.     

Green gelatin-assisted: Synthesis of Co3O4NPs@rGO nanopowder for highly efficient magnetically separable methylene orange dye degradation

GO and Co(NO₃)₂ were respectively used as rGO and Co₃O₄ precursors for preparing magnetically separable Co₃O₄NPs attached Co₃O₄NPs@rGO nanocomposites by a straightforward sol–gel technique. To characterize the nanocomposite materials, FESEM, EDX, elemental mapping, XRD, FTIR, Raman spectroscopy, UV–vis, VSM and BET were employed. When exposed to UV rays, the nanocomposite showed extraordinary photocatalytic degradation of MO dye. According to the measurements of photocatalytic activity, the highly efficient photocatalytic efficiency of the nanocomposite could be attributed to preventing electron-hole recombination by highly effective electron transfer between rGO and semiconductor NPs. The nanocomposite succeeded in the efficient degradation of MO dye, even after five photocatalytic cycles.     

Fabrication and characterization of novel Ag2O-polyimide composites with enhanced visible-light photocatalytic activity

Novel high-efficiency visible-light photocatalyst, silver oxide (Ag₂O)-polyimide (PI) photocatalyst is synthesized by a liquid phase reaction method. The obtained samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectra (FT-IR) and photoluminescence (PL). The photocatalytic activity of the Ag₂O-PI composites are evaluated by the decomposition of Rhodamine B (RhB) under visible-light irradiation. All Ag₂O-PI composite possesses higher photocatalytic activity than pure Ag₂O and PI. It could be found that RhB was photodegraded with the highest degradation efficiency of 97.9% when the mass ratio of Ag₂O and PI reached to 2:1. This enhancement can be attributed to the efficient separation of photogenerated electron and holes. Furthermore, the possible mechanism for the photocatalytic activity of Ag₂O-PI composites was also proposed.     

TiCl3、TiCl4共水解制备金红石相氧化钛粉体

通过TiCl3、TiCl4共同水解可以制备出金红石相的氧化钛粉体．改变原料浓度可以控制产物的形貌，较高浓度下得到300—500nm的球状颗粒，由许多细小晶粒组成；较低浓度下得到纳米针状颗粒．提高TiCl3的浓度可以使晶粒尺寸有所减小．     

Ag/TiO2薄膜结构和光催化性能研究

采用溶胶-凝胶技术制备了Ag掺杂的TiO2薄膜.用XRD、氮吸附法、UV-VIS-NIR分光光度计以及XPS对Ag掺杂后TiO2薄膜结构的变化进行了分析;用分光光学法通过在紫外光照下分解亚甲基蓝的实验比较了TiO2薄膜与Ag/TiO2薄膜的光催化性能.结果发现,掺杂适量的Ag有助于TiO2薄膜光催化氧化性能的提高,原因在于:（1）Ag通过引入耗尽层提高了TiO2的电荷分离能力,并吸引空穴向薄膜表面移动,结果使薄膜表面空穴的浓度提高,薄膜光催化效率提高;（2）Ag减小了TiO2粒子的粒径,使TiO2禁带宽度增大,薄膜光催化氧化的能力提高;（3）Ag掺杂后,TiO2薄膜表面对-OH基和水的吸附增加,使光照后TiO2薄膜表面活性自由基·OH的浓度增加,空穴向薄膜所吸附物质的转移能力提高.     

Facile synthesis of nano-TiO2/stellerite composite with efficient photocatalytic degradation of phenol

In this paper, we report a kind of nano-TiO₂/stellerite composite with enhanced photoactivity, which was synthesized by a typical homogeneous precipitation method followed by a calcination crystallization process using natural stellerite as support. The as-prepared composites were characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM), nitrogen adsorption-desorption, high resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS). The results showed that TiO₂ loading amounts and calcination temperatures had significant influence on the adsorption and photocatalytic degradation properties of phenol. Moreover, it was indicated that the TiO₂ nanoparticles (NPs) with smaller grain size (around 12.0?nm) and narrower size distributions were uniformly deposited on the surface of stellerite as a layer of film. Compared with commercial P25, the received composite exhibited more superior photocatalytic degradation performance towards phenol. The enhanced photocatalytic degradation performance should result from the better dispersibility of TiO₂ NPs and higher separation efficiency of photogenerated electron-hole pairs. This work may set foundation for the practical application of this new composite photocatalyst in the field of wastewater treatment.