| 搭接率对TC4表面Ni60A熔覆层组织性能的影响 |
| |
| 引用本文： | 龚玉玲,武美萍,崔宸,缪小进. 搭接率对TC4表面Ni60A熔覆层组织性能的影响[J]. 金属热处理, 2021, 46(9): 229-233. DOI: 10.13251/j.issn.0254-6051.2021.09.041 |
| |
| 作者姓名： | 龚玉玲 武美萍 崔宸 缪小进 |
| |
| 作者单位： | 江南大学 机械工程学院, 江苏 无锡 214122;泰州学院 船舶与机电工程学院, 江苏 泰州 225300;江南大学 机械工程学院, 江苏 无锡 214122 |
| |
| 摘 要： | 利用激光熔覆同轴送粉技术,在TC4钛合金表面制备了多道搭接的Ni60A激光熔覆层.利用SEM、硬度测试及摩擦磨损试验,对多道搭接率(30％、40％、50％、60％和70％)下熔覆层的组织性能进行了分析.结果表明:搭接率对Ni60A熔覆层的组织性能影响较大,搭接可实现涂层的二次加热,当搭接率为50％时,涂层中硬质相TiC...
|
| 关 键 词： | 激光熔覆 Ni60A熔覆层 搭接率 微观形貌 耐磨性 硬度 |
| 收稿时间： | 2021-03-29 |
Effect of overlap rate on microstructure and properties of Ni60A clad coating on TC4 titanium alloy |
| |
| Gong Yuling,Wu Meiping,Cui Chen,Miao Xiaojin. Effect of overlap rate on microstructure and properties of Ni60A clad coating on TC4 titanium alloy[J]. Heat Treatment of Metals, 2021, 46(9): 229-233. DOI: 10.13251/j.issn.0254-6051.2021.09.041 |
| |
| Authors: | Gong Yuling Wu Meiping Cui Chen Miao Xiaojin |
| |
| Affiliation: | 1. School of Mechanical Engineering, Jiangnan University, Wuxi Jiangsu 214122, China;2. School of Shipping and Mechatronic Engineering, Taizhou University, Taizhou Jiangsu 225300, China |
| |
| Abstract: | Multi-pass Ni60A laser clad coating was prepared on the surface of TC4 titanium alloy by using laser cladding coaxial powder feeding technology. The microstructure and properties of the clad coating with overlap rates (30%, 40%, 50%, 60% and 70%) were analyzed by using SEM, hardness test, and friction and wear test. The results show that the overlap rate has a greater impact on the microstructure and properties of the clad coating, which can realize the secondary heating of the coating. When the overlap rate is 50%, the size of hard phase TiC and the content of TiNi in the coating increase, which can effectively improve the hardness of the coating, resist the shear force on the grinding ball, so that the surface is not easy to be damaged, and the surface of the coating is smooth, which can greatly reduce the friction coefficient. When the overlap rate is 30%, the grains can't fully absorb the laser energy, resulting in smaller grain size. But when the overlap rate is too high, the B, C, Ni and other elements in the coating will be diluted with the over burning, resulting in the loss of reinforcing elements in the coating and reducing the mechanical properties of the coating. Therefore, the most suitable overlap rate of the Ni60A coating is 50%. |
| |
| Keywords: | laser cladding Ni60A clad coating overlap rate microstructure wear resistance hardness |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《金属热处理》浏览原始摘要信息 |
|
点击此处可从《金属热处理》下载全文 |
|
