| 基于溶解度参数分析方法的IPN密封材料研究 |
| |
| 引用本文： | 吴力力,丁玉奎,甄建伟,陈思扬,张伟光,王霞,张国兴.基于溶解度参数分析方法的IPN密封材料研究[J].包装工程,2017,38(23):83-87. |
| |
| 作者姓名： | 吴力力 丁玉奎 甄建伟 陈思扬 张伟光 王霞 张国兴 |
| |
| 作者单位： | 军械工程学院，石家庄 050003,军械工程学院，石家庄 050003,军械工程学院，石家庄 050003,军械工程学院，石家庄 050003,66352部队，北京 101508,69223部队，拜城 842300,69223部队，拜城 842300 |
| |
| 摘 要： | 目的基于耐溶剂性原则选择硝酸异丙酯的密封材料。方法通过溶解度参数的计算验证丁腈橡胶(NBR)与IPN会产生溶胀效应。根据聚合物的耐溶剂性原则,选择三元乙丙橡胶(EPDM)和聚四氟乙烯(PTFE)代替丁腈橡胶,而后比较各材料与IPN的溶解度参数差值。结果 IPN在NBR的可溶球体范围内,两者的三维溶解度参数十分接近;IPN,EPDM与PTFE的一维溶解度参数分别为8.6,7.7,5.14,EPDM与IPN的溶解度参数较为接近;PTFE与IPN的溶解度参数相差较大。结论 EPDM与PTFE均比NBR更适合密封IPN,其中EPDM最适合密封IPN。
|
| 关 键 词： | 丁腈橡胶 三元乙丙橡胶 聚四氟乙烯 溶解度参数 |
| 收稿时间： | 2017/5/24 0:00:00 |
| 修稿时间： | 2017/12/10 0:00:00 |
IPN Sealing Material Based on Solubility Parameter Analysis Method |
| |
| WU Li-li,DING Yu-kui,ZHEN Jian-wei,CHEN Si-yang,ZHANG Wei-guang,WANG Xia and ZHANG Guo-xing.IPN Sealing Material Based on Solubility Parameter Analysis Method[J].Packaging Engineering,2017,38(23):83-87. |
| |
| Authors: | WU Li-li DING Yu-kui ZHEN Jian-wei CHEN Si-yang ZHANG Wei-guang WANG Xia and ZHANG Guo-xing |
| |
| Affiliation: | The Ordnance Engineering College, Shijiazhuang 050003, China,The Ordnance Engineering College, Shijiazhuang 050003, China,The Ordnance Engineering College, Shijiazhuang 050003, China,The Ordnance Engineering College, Shijiazhuang 050003, China,66352 Troops, Beijing 101508, China,69223 Troops, Baicheng 842300, China and 69223 Troops, Baicheng 842300, China |
| |
| Abstract: | The work aims to select the sealing material of isopropyl nitrate (IPN) based on the solvent resistance principle. The fact that nitrile rubber (NBR) and IPN would result in swelling effect was verified by calculating the solubility parameters. According to the principle of solvent resistance, EPDM rubber and polytetrafluoroethylene (PTFE) were selected instead of NBR. Then, the difference between the solubility parameters of each material and IPN was compared. IPN was within the range of NBR soluble sphere and the three-dimensional solubility parameters of both were very close. The one-dimensional solubility parameters of IPN, EPDM and PTFE were 8.6, 7.7 and 5.14, respectively. The solubility parameters of EPDM and IPN were close to each other; the solubility parameters of PTFE and IPN were quite different. EPDM and PTFE are more suitable for sealing IPN than NBR, and EPDM is the most suitable for sealing IPN. |
| |
| Keywords: | nitrile rubber EPDM polytetrafluoroethylene solubility parameters |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《包装工程》浏览原始摘要信息 |
|
点击此处可从《包装工程》下载全文 |
|
