掺杂聚苯胺的表面接枝共聚改性

化学氧化法制备的聚苯胺表面的亲水性差，本文在本征态和不同酸掺杂志聚苯胺的表面上接枝共聚丙烯丙烯酸和丙烯酰胺，明显地改善了聚苯胺的表面亲水性。结果显示，聚苯胺表面经过等离子体处理后，有利于丙烯酸和丙烯酰胺在聚苯胺表面上的接枝共聚，随着接枝量增多，导电率则随之有所下降，此外，利用ＳＥＭ和反射ＩＲ表征了改性反聚苯胺表面的形态和结构。     

Fe2O3/TiO2和ZnO/TiO3纳米颗粒薄膜的亲水性能和光催化性能的研究

采用溶胶—凝胶法在玻璃上制备了锐钛矿型TiO2和过渡金属铁、锌离子掺杂的TiO2薄膜，并通过XRD、XPS、AFM表征了合成的薄膜．结果表明铁和锌离子掺入后，TiO2薄膜变的更加致密．铁离子和锌离子分别以Fe2O3和ZnO的形式存在．在紫外光照射下，TiO2薄膜表现明显的亲水性．金属离子掺杂的TiO2薄膜，亲水性能明显增强．铁离子掺入对光催化降解甲基橙有一定的抑制作用；少量的锌离子掺入对光催化降解甲基橙有促进作用，锌离子掺入量增大后，效果并不明显．     

臭氧氧化处理法对聚丙烯表面涂装性的改良 Ⅳ.聚丙烯表面亲水性和涂膜剥离强度的关系

讨论了用臭氧氧化法对聚丙烯表面进行涂装性改良时,丙烯均聚物、乙烯-丙烯嵌段共聚物及无规共聚物表面以接触角表示的亲水性和涂膜剥离强度之间的关系。结果表明,当聚丙烯表面对水的接触角在84°附近时,可反应型涂料的涂膜剥离强度将出现最大值。在此也证明了涂膜的剥离破坏存在着接着破坏和凝集破坏两种机理,当接触角减小到84°及84°以上时,剥离发生在聚丙烯和涂层的界面上产生接着破坏;当接触角减小到84°以下时,剥离发生在聚丙烯的表面氧化层相中,产生凝集破坏。     

Al2O3包覆石墨颗粒的制备及表征

以Al(NO3)3·9H 2O为主要原料,采用非均匀成核技术在鳞片状石墨表面包覆一层Al2O3,制备成石墨/氧化铝复合粉体.对复合粉体的制备条件、表面形貌和特性进行了研究.研究表明pH值、处理温度和覆层物质前驱体浓度是影响包覆的主要因素.TEM观察和XPS能谱检测表明,石墨颗粒表面均匀包覆有一层Al2O3.包覆后石墨表面由疏水转为亲水.     

聚乙二醇重氮树脂在聚乙烯膜材料表面的自组装及亲水改性

用铬酸氧化法在聚乙烯薄膜的表面引入了羧基阴离子,合成了端基阳离子性的聚乙二醇重氮树脂,用静电自组装并辅以紫外光照射的方法,在聚乙烯薄膜的表面引入了共价键连接的聚乙二醇分子链.用紫外-可见分光光度法研究了重氮树脂及其静电自组装体系的光分解性质,得到重氮基团的分解速率常数kd=0.021 4 s-1.红外分析表明,紫外光照射后聚乙烯薄膜表面连接的聚乙二醇分子链可耐DMF-ZnC l2-H2O三元极性溶剂的刻蚀.由于在聚乙烯薄膜的表面引入了亲水性的聚乙二醇分子链,其表面接触角从改性前的104°降至48°.     

Synthesis and characterization of poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers

Poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers with predetermined block lengths were synthesized by polycondensation of PLA diols and PEG diacids. The reaction was carried out under mild conditions, using dicyclohexylcarbodiimide as the coupling agent and dimethylaminopyridine as the catalyst. The resulting copolymers were characterized by various analytical techniques, such as GPC, viscometry, ¹H‐NMR, FTIR, DSC, X‐ray diffractometry, and contact angle measurement. The results indicated that these copolymers presented outstanding properties pertinent to biomedical use, including better miscibility between the two components, low crystallinity, and hydrophilicity. Moreover, the properties of the copolymers can be modulated by adjusting the block length of the two components or the reaction conditions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1729–1736, 2002; DOI 10.1002/app.10580     

Studies on grafting of acrylic acid onto polypropylene melt‐blown nonwovens induced by electron‐beam preirradiation

We report the graft copolymerization of acrylic acid onto the polypropylene (PP) melt‐blown nonwovens induced by electron beam (EB) preirradiation in this article. The occurrence of the graft copolymerization was confirmed by means of XPS, FTIR, and SEM. The effects of preirradiation dose, monomer concentration, bath ratio, reaction time, and temperature on the graft ratio were investigated. The water conservation, water absorption rate, and K⁺ exchange capacity were also determined on the grafted PP melt‐blown nonwovens, which showed that EB preirradiation‐induced grafting was an effective way to improve the hydrophicility of PP melt‐blown nonwovens. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4971–4977, 2006     

溅射气氛中O2／Ar比及热处理对直流反应磁控溅射法制备玻璃基TiO2薄膜结构与亲水性的影响

在工作气压为0．80Pa的氧氩气混合气氛下，改变氧与氩的流量比(O2／Ar：0．10，0．20，0．30)，在预先镀10nm左右SiO2的普通玻璃基片上用直流(D．C．)磁控溅射法制备了300nm左右的TiO2薄膜试样。离线在500℃、氧气氛下对试样热处理2h。用X射线光电子能谱(XPS)和X射线衍射仪(XRD)分别研究了试样热处理前后的表面元素组成、离子状态和物相组成，用接触角分析仪测试了试样在紫外光(UV)照射后的水润湿角。     

表面处理对亲水铝箔持续亲水性的影响

通过测定水洗200h后,水滴在亲水铝箔表面接触角的方法来确定脱脂和铬化对亲水铝箔持续亲水性的影响。发现只要清洗彻底,则持续亲水性与脱脂剂的种类无关。铬化对持续亲水性的影响很大,用磷酸铬酸盐法处理的铝箔,其持续亲水性比用铬酸盐法处理的要好。用磷酸铬酸盐法于30℃,将铝箔处理3min,最后涂布亲水涂层得到的亲水铝箔,其持续亲水性最佳,水冲200h后,接触角为9～11°。