梯度铝蜂窝夹芯板的力学行为

梯度分层铝合金蜂窝板是一种有效的吸能结构,本工作在梯度铝蜂窝结构的基础上根据梯度率的概念,通过改变蜂窝芯层的胞壁长度,设计了4种质量相同、梯度率不同的铝蜂窝夹芯结构。通过准静态压缩实验,并结合非线性有限元模拟准静态及冲击态下梯度铝蜂窝夹芯结构的变形情况及其力学性能,分析对比了相同质量下梯度铝蜂窝夹芯结构在准静态下的变形模式以及冲击载荷下分层均质蜂窝结构和不同梯度率的分层梯度蜂窝结构的动态响应和能量吸收特性。结果表明:在准静态压缩过程中,铝蜂窝梯度夹芯板的变形具有明显的局部化特征,蜂窝芯的变形为低密度优先变形直至密实,层级之间的密实化应变差随芯层密度的增大而逐渐减小;在高速冲击下,梯度蜂窝板并非严格按照准静态过程中逐级变形直至密实,而是在锤头冲击惯性及芯层密度的相互作用下整体发生的线弹性变形、弹性屈曲、塑性坍塌及密实化;另外,在本工作所设计的梯度率中,当梯度率为γ₁=0.0276时,梯度蜂窝夹芯板的吸能性达到最好,相较于同等质量下的均质蜂窝夹芯板,能量吸收提高了10.63%。     

Selective Coating of SnS on the Bio‐Inspired Moth‐Eye Patterned PEDOT:PSS Polymer Films

A new strategy for the selective coating of tin sulfide (SnS) on the surface of moth‐eye patterned (MEP) conducting polymer film is studied by considering the optical properties of the antireflective moth‐eye pattern and flexibility of polymer films. The semiconductor SnS is selectively coated on the surface of MEP microdomes of poly(3,4‐ethylenedioxythiophene) poly(styrene‐sulfonate) (PEDOT:PSS) film. The SnS coated MEP film is obtained by using pore selectively SnS thin layer functionalized polystyrene honeycomb‐patterned porous (HCP) film as a template. Aqueous PEDOT:PSS solution is poured on the SnS functionalized HCP films and detached for the fabrication of SnS coated MEP films. The films show a satisfactory photo‐responsive property under solar stimulated light illumination due to the antireflective MEP structure of PEDOT film and homogenous SnS coating on the surface of the conducting polymer.     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Structural dimension optimization and mechanical response analysis of fabricated honeycomb plastic pavement slab

Because of favorable mechanical properties, deformation resistance and being conducive to environmental protection, honeycomb fabricated plastic pavement slabs are highly recommended these years. At present, most studies focus on the performance of plastic materials, however, the dimension optimization of fabricated plastic pavement slab is rarely mentioned. In this paper, an optimized geometry of the honeycomb pavement slab was determined through finite element analysis. Mechanical response of honeycomb slabs with different internal dimensions and external dimensions were explored. Several dimension factors were taken into consideration including the side length, rib thickness, the thickness of both top and bottom slabs of honeycomb structure and the length, the width and the thickness of the fabricated plastic slab. The results showed that honeycomb pavement slab with 6 cm bottom slab, 12 cm top slab,18 cm side length and 6 cm rib thickness is recommended, additionally, an external dimension of 4 m × 4 m × 0.45 m is suggested. Then, the mechanical responses of this optimized fabricated plastic slab were further investigated. Significance of different influencing factors, including wheel load, elastic modulus of plastic material, base layer thickness, soil foundation modulus and base layer modulus were ranked.     

蜂窝陶瓷负载锰酸锶镧基催化剂制备及性能

采用不同浓度硝酸和草酸溶液,对堇青石蜂窝陶瓷载体进行预处理,考察了酸处理对载体失重率、吸水率及压缩强度的影响。采用催化剂粉体浆料涂覆法,制备了堇青石蜂窝陶瓷负载锰酸锶镧基La0.8Sr0.2Mn0.4Al0.4Zn0.2O3-δ(LSMAZ)整体式催化剂,运用X射线衍射(XRD)、扫描电镜(SEM)等手段对催化剂进行表征,并在管式反应器上进行甲烷催化燃烧活性测试。结果表明,酸处理能增大载体比表面积和吸水率;相同条件下草酸对载体的侵蚀效果优于硝酸;提高草酸浓度能增强侵蚀效果,但过高浓度的酸处理会使载体压缩强度过小而无法应用。经1050℃煅烧5 h后,所制备的整体式催化剂具有适宜的脱落率,无明显载体-LSAMZ界面反应,并具有最高的甲烷燃烧催化活性。     

蜂窝陶瓷蓄热材料的研究现状

蜂窝陶瓷蓄热材料应该具有热膨胀系数低、比热容大、比表面积大、导热性能好、抗热震性好等特性。本文详细介绍了几种多孔陶瓷材料的优缺点,指出堇青石质复相材料是目前研究最广泛的蜂窝陶瓷材料。堇青石与多种催化剂匹配性好,比表面积大、热膨胀系数小,但耐热性稍差,于是通过添加一些添加剂来提高堇青石作为蜂窝陶瓷蓄热体的性能。这些添加剂与堇青石结合形成复相材料,可以降低热膨胀系数、提高抗热震性等。     

清洗工艺对GH4099蜂窝夹层结构钎焊性能的影响

目的 研究激光清洗和离子轰击对GH4099蜂窝夹层结构钎焊性能的影响,优化GH4099蜂窝夹层结构焊前清洗工艺。方法 分别用400#砂纸、不同激光功率(60~200 W)、不同离子轰击时间(1~2 h)对GH4099带材表面进行了砂纸打磨、激光清洗和离子轰击试验,分析了激光清洗和离子轰击对GH4099表面形貌、O元素含量、BNi2钎料润湿性的影响,测试了不同清洗工艺下蜂窝夹层结构钎焊接头的拉伸性能。结果 随激光功率从60 W增加到100 W,GH4099表面O含量逐渐降低,表面粗糙度逐渐增大,钎料润湿面积百分比增加到83.5%,润湿性增加。当激光功率大于100 W时,表面残留网状分布的氧化物,导致钎料润湿性降低。当激光功率进一步增加到200 W时,氧化物网状分布现象减轻,润湿性随之增加,粗糙度也有所降低;随离子轰击时间从1 h增加到2 h时,带材表面氧化皮逐渐去除干净,钎料润湿性随之增加,钎料对离子轰击2 h的表面的润湿面积百分比达到91.2%,与400#砂纸打磨的相当。经离子轰击2 h、1 020 ℃-15 min钎焊获得的夹层结构等效抗拉强度为11.9 MPa。结论 与激光清洗相比,离子轰击可以同时去除蜂窝型面及附近侧壁部分的氧化皮,能更有效地改善钎料对蜂窝基体的润湿性。     

新型玻璃钢蜂窝夹层结构模板的试验研究

本文提出以玻璃钢板、纸蜂窝及适当玻璃钢管制成的一种新型建筑模板。新型夹层模板的荷栽试验结果表明：在芯层中加入玻璃纤维管能有效控制夹层结构的剪切变形，提高面板材料的利用率。该种新型模板的变形及承栽能力均满足施工要求。在试验研究的基础上，本文给出新型夹层结构的应力和挠度计算公式。     

植物纤维纸蜂窝制备的环境影响评价

利用CML环境影响评价方法,研究并比较了植物纤维纸蜂窝和传统芳纶纸蜂窝制备的环境影响。结果表明,针对所涉及的11个环境影响指标,植物纤维纸蜂窝低于芳纶纸蜂窝0.68 %~49.41 %;权重化结果表明,植物纤维纸蜂窝制备环境影响总体低于芳纶纸蜂窝18.77 %;制备芳纶纸蜂窝的环境影响主要来自于芳纶纸和电能的消耗;制备植物纤维纸蜂窝的环境影响主要来自于混杂纸和电能的生产。