基于CFD⁃DEM的水下切粒装置水室内颗粒流动过程数值模拟

基于CFD?DEM耦合方法，研究了颗粒在水室内的流动状态，分析了不同刀盘转速、粒子水通入量和水室出口角度对造粒过程的影响，发现提高刀盘转速、增加粒子水通入量和水室出口倾斜一定的角度都有利于水室内颗粒的排出。进一步研究了颗粒与碎屑在水室内的流动，发现在水室出口处二者的流动基本呈现出一定的分离角度。     

Experimental and numerical investigations on the heat production and thermal storage characteristics of rapid preparation amorphous powder activated coke

The heat production and thermal storage characteristics of rapid-preparation amorphous powder activated coke (RAC) were investigated. RAC was prepared by using a drop-tube reactor system. The natural oxidation characteristics of RAC were studied through combined TG–FTIR analysis and temperature-programmed experiment. Experimental results showed that CO and CO₂ were the main oxidation products of RAC in air, and that the oxidation reaction was in accordance with the Arrhenius equation and law of mass action. Thermal storage characteristics were studied through computational fluid dynamics simulation. The maximum excess temperature θ_max increases linearly with the increase of the initial temperature. The concentration fields of the products show that CO₂ is mainly concentrated in the upper part of the coke bin, and the CO generated by CO₂ at high temperature is mainly concentrated in the central part of the coke bin.     

Evaluation of cut cell cartesian method for simulation of a hook and claw type hydrogen pump

Hook and claw pumps are used for recirculation of excess hydrogen in fuel cells. Optimization of the pump design is essential. Computational Fluid Dynamic (CFD) is an effective method for performance optimization. However, it is difficult to conduct CFD simulation because of the sharp cusp of the rotor profile. Cut cell Cartesian mesh could be the solution to handle this complex and moving geometries. The aim of this paper is to evaluate ANSYS Forte for hook and claw pumps. Firstly, the conservation accuracy of the cut cell cartesian mesh is verified using an adiabatic piston cylinder case. Then, simulation results of hook and claw type pump are compared with experimental data. Finally, simulation results of air and hydrogen are compared. The results show that the CFD simulation of hook and claw pumps using cut cell cartesian mesh could provide an efficient and effective approach for the optimization of the system.     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

Computational modelling of water flow inside laboratory Knelson concentrator bowl

Enhanced gravity concentrators such as Knelson concentrator (KC) are extensively used in the mineral processing industry. The complexities of KC bowl geometry and variation of feed characteristics have forced process engineers to design empirically new units using laboratory and pilot-scale Knelson concentrators. However, numerical modelling methods such as computational fluid dynamics (CFD) and discrete element method (DEM) provide a better insight of flow behaviour of fluid and particulate solid phases inside these processing units. This article reports findings of CFD simulations for single-phase water flow inside the laboratory KC. An available standard 7.5-cm laboratory KC bowl was numerically simulated using realisable k-ε turbulence model to resolve the turbulence dispersion of existing transitional flow regime. The effects of relative centrifugal force (RCF) intensity and bed fluidisation water flow rate on the water velocity and pressure distributions were studied. Simulations confirmed the swirling flow pattern governing inside the bowl. The results revealed that the impact of RCF intensity on the water field values is greater than that of bed fluidisation water flow rate. Both velocity and pressure variations inside the bowl rings followed a linear trend.     

住宅新风系统风量分配装置压力平衡研究

为确保住宅建筑新风系统风量的合理分配,本文提出了一种新风系统设计方法,并通过计算流体力学模拟了一体积较小且带有六个出口的风量分配装置,以在不同位置设置不同长度的导流板的方式,得出在两侧设置长度为43 mm的导流板,在中心设置长度为44 mm导流板时,可以实现在一定风量范围内达到风量平衡且出口压力相等。     

Novel hybrid serpentine-interdigitated flow field with multi-inlets and outlets of gas flow channels for PEFC applications

In our previous study, a novel flow field design for a polymer electrolyte fuel cell (PEFC) called “Hybrid Serpentine-Interdigitated (HSI)” had been proposed. Although it was very promising in terms of performance and pressure drop, it still had a major drawback of the low oxygen concentration area. To improve its design and performance, three HSI configurations with different numbers of gas inlet and outlet, namely one inlet and one outlet HSI (1-IO HSI), one inlet and two outlets HSI (1I-2O HSI) and two inlets and two outlets HSI (2-IO HSI) were numerically investigated and compared with the conventional single channel serpentine (1S). The investigation on the cell performance and other transport behaviors has been carried out using CFD techniques via ANSYS FLUENT software. At a practical operating potential of about 0.6 V of 50 cm² PEFCs, the 2-IO HSI offered the best distributions of oxygen, current density and water due to the shorter channel length. More importantly, the 2-IO HSI could contribute to a reduction in cathode pressure drop by 90%, as compared with the 1S, resulting in the enhancement in the net power output by 6%, approximately.     

基于CFD技术优化50 L发酵罐内气体分布器

通过CFD模拟技术对50L通气搅拌发酵罐内不同气体分布器的传质混合效果进行气液双相流模拟。首先对发酵罐自带气体分布器进行流场模拟,针对模拟结果提出两种改进气体分布器。结果表明:双层环形气体分布器表现出一种较理想的混合传质效果,为此类发酵罐的优化和放大提供一种有效的技术手段。     

Improved indoor environment through optimised ventilator and furniture positioning: A case of slum rehabilitation housing,Mumbai, India

This study optimized the ventilator and furniture location of a tenement unit in a low-income urban habitat to obtain maximum experiential indoor environmental quality (e-IEQ) over the breathing zone. Hypothetical interior layouts using a combination of the two design parameters of ventilator location and bed position were generated for optimizing the design layout. This layout could promote maximum indoor airflow and minimum indoor air temperature and contaminant concentration. In this study, an improved indoor environment is hypothesized to be attainable through improved natural ventilation and thermal performance in the occupied zones. A sequential methodology involving “parametric design modeling–computational simulation–multiobjective optimization–multicriteria decision making”-based framework was selected. Results exhibited that the currently designed tenement unit had a poor indoor environment, whereas the hypothesized iterated layout “optimized design layout, scenario 3 (ODL 3)” derived from the optimization and decision-making algorithm performed effectively in providing e-IEQ. An increase in experiential indoor air velocity by 0.2 m/s and a decrease in temperature by 2 °C were observed over the monitoring point in the ODL 3 considering the existing scenario. Therefore, this study can find a way toward the development of sustainable habitat design guidelines under upcoming slum redevelopment policies across the nation.