HART通信协议在汽油机速度测量和监控方面的应用

首先介绍了HART通信协议及他的优点，然后介绍了HART通信协议在汽油机测速方面的软件实现。该软件主要采用目前流行的VB编程语言。可设计出界面友好、功能强大的测量和监控软件。     

铁路罐车密闭装车计量系统的运行分析

从中国石化股份公司济南分公司新上铁路罐车密闭装车计量系统的背景出发，阐述该系统的设计思想和组成；通过分析实际运行过程中仪表比对数据，讨论影响仪表贸易交接准确性的各种因素，提出相应的解决方法；最后通过铁路罐车密闭装车计量系统投用效果。证实该系统可产生明显的经济效益。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

火工品压药机装配误差的研究

针对军用雷管生产线中压药机结构,分别用极值法和概率法对压药机冲子和雷管的配合精度,进行了装配尺寸链的描述和计算,并对所得的结果进行了比较。     

A Topological Implementation for Motion Planning of a Robotic Arm

An efficient path planning algorithm based on topologic method is presented in this paper.The collision free path planning for three-joint robotic arm consists of three parts:partition of C-space,construction of CN and search for a path in CN.We mainly solved the problems of partitioning the C-space and undging the connectivity between connected blocks,etc.For the motion planning of a robotic arm with a gripper,we developed the concepts of global planning and local planning,and discussed the basic factors for constructing the planning system.In the paper,some evaluation and analysis of the complexity and reliability of the algorithm are given,together with some ideas to improve the efficiency and increase the reliability.At last,some experimental results are pesented to show the efficency and accuracy of the algorithm.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

AD2S80在测角系统中的应用

DS2S80是美国AD公司生产的以鉴幅方式对感应同步器信号进行处理的专用芯片。由它与感应同步器构成的测角系统具有成本低、功耗小、所需外部元件少、可靠性好等优点。介绍了AD2S80数字转换芯片的引脚、组成测角系统的工作原理、外围电路的设计，给出了一种半量式测角系统的实现方案。     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

压电量测系统漏电影响分析

本文通过对压电量测系统等效电路图的逐步简化,得出矩形脉冲信号的漏电方程;并对系统在各种情况下的时间常数,漏电相对误差进行了计算,最后就系统在校准和现场测试中经常碰到的几种情况,进行了定量估算,从而解决了压电量测系统在使用中的一些具体问题。