Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Dispersion characterization in layered double hydroxide/Nylon 66 nanocomposites using FIB imaging

Layered double hydroxides (LDHs), a newly emerging 2D host material, consist of cationic brucite-like layers and exchangeable interlayer anions. In this work, the morphology and dispersion of LDH particles in LDH/Nylon 66 (salt) nanocomposites has been investigated using focused ion beam (FIB) techniques, transmission electron microscopy (TEM) and X-ray diffraction (XRD). The FIB images show that LDHs are present in the polymer phase dispersed to different degrees, with partial intercalation, exfoliation, and aggregation all being observed. The most even dispersion was achieved in nanocomposites with the lowest loading (0.5 wt % LDH). Residual tactoids and agglomerates were most common in the samples made with the highest concentration of LDHs studied here (5 wt %). The dispersion observed using FIB was consistent with TEM and XRD analysis, yet this technique had significant benefits in terms of time and simplicity over these “conventional” technologies. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

增强增韧尼龙66工程塑料流变行为的研究

对以合金化技术改性所得增强增韧尼龙６６进行流变行为研究的结果表明，填充玻纤，可使其增强，但使流动性能下降：共混接枝聚丙烯，可使其增韧，并改善加工流动性，填充超细滑石粉，除有一定增强作用外，也使加工流动性，制品表面光滑程度和尺寸稳定性得到改善。填充共混的协同作用使改性尼龙６６有较好的综合性能。     

PVA/UiO-66复合薄膜的制备及性能表征

采用溶剂热法合成出了金属有机骨架材料UiO-66,并通过流延法制备出了一系列PVA/UiO-66复合膜。通过红外光谱仪(FTIR)、X射线衍射仪(XRD)、扫描电子显微镜(SEM)、接触角、溶胀度、拉伸强度和透光性等表征方法,详细研究了UiO-66含量对复合膜各种物性的影响。结果表明,PVA在经富马酸交联后,耐水溶胀性和拉伸性能都得到了显著改善。随着UiO-66负载量的提高,复合膜的溶胀度、拉伸强度和透光性能逐渐降低,而水接触角和甘油接触角逐渐增大。     

补强剂和共混工艺对PA/PVC/NBR三元共混弹性体性能的影响

在选择三元共聚尼龙（PA）、聚氯乙烯（PVC）、丁腈橡胶（NBR）为主体材料，制备PA／PVC／NBR（10／30／60）三元共混弹性体的工作基础上，进一步探讨了填料品种和用量，共混温度，加料顺序等因素PA／PVC／NBR三元共混弹性体的影响。试验结果表明：在PA／PVC／NBR（10／30／60）共混体系中，补强型填料的补强效果优于非补强型的填料，6种填料补强效果依次是：快压出炭黑＞半补强炭黑＞白炭黑＞活性重质，CaCO3＞陶土＞滑石粉，快压出炭黑的适宜用量是20－50份。在制备PA／PVC／NBR三元共混物时，适宜的共混温度是122－140℃，并且采用二段法混工艺制得的共混物性能优于采用一段法共混工艺。     

Studies on crystallization behaviors and crystal morphology of polyamide 66/clay nanocomposites

X‐ray diffraction methods, DSC thermal analysis, and polarized light microscopy (PLM) were used to investigate the structural changes of nylon 66/clay nanocomposites. PA 66/clay nanocomposites were prepared by the method of melt intercalation. The results indicate that the addition of the intercalated organo‐montmorillonite (OMMT) can induce generation of the β‐form crystal of PA 66 and substantially affect the arrangement of molecules in the α‐form crystal, although the crystallinity scarcely changes. Also, the DSC results indicate that the addition of OMMT in the PA 66 matrix leads to increases of crystallization temperatures and the full width at half maximum (FWHM) of the exothermic peaks. Moreover, the viscosity factor is the main influence on FWHM of the exothermic peaks of PA 66/clay nanocomposites. The results of nonisothermal crystallization kinetics show that OMMT has the effect of heterogeneous nucleation and leads to the decrease of the size of the spherocrystal. The heterogeneous nucleation effects of OMMTs influence the mechanism of crystallization and the growth mode of PA 66 crystals. PLM photographs verify that the size of spherocrystal is decreased and visually confirm the theory of crystallization kinetics. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 756–763, 2005     

汽车起动机齿轮拨叉失效分析

分析了引起汽车起动机齿轮拨叉收缩变形及强度低所引起的制品失效原因,采用定型棒对制品进行定型以补偿拨叉的收缩变形;通过改进浇口位置来调整玻璃纤维在制品中的取向,使拨叉受力方向与玻璃纤维取向平行,从而消除了制品因强度低所引起的失效。     

锦纶66浸胶帘子布生产中的张力与控制

分析了帘子布生产中张力的作用及各区段的张力情况。张力应根据生产品种及浸胶帘子布的内在质量要求来选择，一般张力设定依据为拉伸区张力是干燥区张力的１倍，定型区张力是拉伸区张力的０．６５倍。同时应控制好各区段的温度，降低拉伸应力使锦纶６６帘子布拉伸均匀，提高帘子布的物理性能。     

聚酰胺66的复配阻燃研究

采用35％磷-溴-锑复配阻燃体系对聚酰胺66进行阻燃，极限氧指数可提高到33．6％，达到UL94-V0级(1．6mm)，且无熔融滴落。阻燃体系的添加会导致聚酰胺66力学性能的下降，但与无机阻燃体系相比较，磷-溴-锑复配阻燃体系对聚酰胺66的力学性能影响较小。采用扫描电镜观察阻燃剂在聚酰胺66中的分散效果，发现分散均匀的体系，在水中或者在110℃的析出实验条件下，阻燃剂的析出量很小，可以维持较长时间的阻燃效果。     

玻纤增强PA66／PP合金的特性及应用

介绍玻纤增强ＰＡ６６／ＰＰ合金的制备工艺及特性，与纯尼龙６６树脂相比，加工性能好，综合性能优异。该材料适用于中小型油浸式变压器的分接开关及其它绝缘部件。