Performance characteristics of concrete based on a ternary calcium sulfoaluminate–anhydrite–fly ash cement

This paper reports an assessment of the performance of concrete based on a calcium sulfoaluminate–anhydrite–fly ash cement combination. Concretes were prepared at three different w/c ratios and the properties were compared to those of Portland cement and blast-furnace cement concretes. The assessment involved determination of mechanical and durability properties. The results suggest that an advantageous synergistic effect between and ettringite and fly ash (Ioannou et al., 2014) was reflected in the concrete’s low water absorption rates, high sulfate resistance, and low chloride diffusion coefficients. However, carbonation depths, considering the dense ettringite-rich microstructure developed, were higher than those observed in Portland cement concretes at a given w/c ratio. It was concluded that the amount of alkali hydroxides present in the pore solution is as important factor as the w/c ratio when performance of this type of concrete is addressed.     

Chloride migration in concrete with superabsorbent polymers

Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete mixtures are tested 7, 14, and 28 days after casting. The development of degree of hydration is followed for 20 corresponding paste mixtures.Both when SAP is added with extra water to compensate the SAP water absorption in fresh concrete and without extra water, the internal curing water held by SAP may contribute to increase the degree of hydration. No matter if SAP is added with or without extra water, it appears that the so-called gel space ratio can be used as a key parameter to link age and mixture proportions (water-to-cement ratio and SAP dosage) to the resulting chloride migration coefficient; the higher the volume of gel solid relative to the space available for it, the lower the chloride migration coefficient, because the pore system becomes more tortuous and the porosity becomes less.     

Transport of a surface-applied corrosion inhibitor in cement paste and concrete

Surface-applied corrosion inhibitors are a kind of repair material and usually contain an aminoalcohol and a component forming a salt with the aminoalcohol. According to the manufacturers, this type of inhibitor penetrates very rapidly into concrete; however, the transport mechanisms have not been sufficiently investigated so far. The major part of the study therefore focused on the transport of the ingredients of an inhibitor in cement paste and concrete, which contained an aminoalcohol and a phosphorous compound. It has been shown that the latter forms an insoluble calcium salt in the environment of cement and precipitates quantitatively. It is thus unable to penetrate from the outside into the alkaline concrete zone and cannot develop its inhibiting effect there. The aminoalcohol, on the other hand, is not bound by cement, but remains largely dissolved in the pore liquid, thus providing optimal conditions for high mobility. The analysis of the transport mechanisms involved has revealed that diffusion in the dissolved state is by far the most efficient transport mechanism. While basically the transport of the aminoalcohol via the gaseous phase is possible, it does play an inferior role only. Surprisingly, the substance had hardly been absorbed by concrete by capillary suction, but at first remained close to the concrete surface.     

大型现浇钢筋混凝土U型渡槽施工技术

禹门口提水工程干渠上的十几座大型钢筋混凝土渡槽采用现浇混凝土施工方案。经过十几座渡槽的施工及通水检验，证明现浇施工技术与工艺已经成熟。本文就施工中遇到的高大排架外形与垂直度控制、槽身模板制做与固定、模具的空中支撑、运输与入仓办法等做以简单介绍。     

Reliability and scale effect in toughness of concrete structures

In the present work, the distribution of the random toughness characteristics (i.e. critical energy release rate, G_1c) has been evaluated on the basis of experimental observations. Fracture test results from three groups of geometrically similar concrete specimens of size (width×total depth×thickness), 420×420×50–1680×1680×200 mm³, made with different maximum aggregate size of 9.5, 19, 38, and 76 mm were analyzed using a recently proposed distribution of extremes. In applications of probability, it is important to use an appropriate distribution type and adequate techniques for estimating the parameters of distribution. In this study, a new type distribution of minima is employed for probability computations. It was noticed that the entropy of distribution increases with the crack length, i.e. the uncertainty of toughness, G_1c, value increases with crack length. A non-linear reduction of the maximum allowable splitting force with the defect size, a, was noticed. For large specimens, the maximum allowable splitting load is more sensitive to the required reliability level than that for small specimens. Reliability increases with aggregate size when all other conditions were constant.     

斗晏水电站混凝土面板堆石坝趾板设计

阐述了江西省重点建设项目斗晏水电站混凝土面板堆石趾板设计，并重点介绍较大断层上趾板设计处理方式。     

峡口水库沥青混凝土面板的施工与试验

以灌溉、防洪为主的峡口水库大坝，为沥青混凝土面板堆石坝，为研究低温抗裂性能，对沥青混凝土面板破损取样，进行了配比和多种力学性能试验，并与原面板设计指标进行了对比。由于面板经受住了－20℃以下的低温考验，其所用沥青指标、破损取样试验结果，特别是冻断低温指标，对确定水工沥青混凝土低温抗裂检验标准有重要参考价值。     

Indicators for inspection and maintenance planning of concrete structures

Based on an idea introduced by Benjamin and Cornell (1970. Probability, statistics and decision for civil engineers. New York: McGaw Hill) and previous works by the authors it is demonstrated how condition indicators may be formulated for the general purpose of quality control and for assessment and inspection planning in particular. The formulation facilitates quality control based on sampling of indirect information about the condition of the considered components. This allows for a Bayesian formulation of the indicators whereby the experience and expertise of the inspection personnel may be fully utilized and consistently updated as frequentistic information is collected. The approach is illustrated on an example considering a concrete structure subject to corrosion. It is shown how half-cell potential measurements may be utilized to update the probability of excessive repair after 50 years. Furthermore in the same example it is shown how the concept of condition indicators might be applied to develop a cost optimal maintenance strategy composed of preventive and corrective repair measures.     

A comparative study of numerical solutions to non-linear discrete crack modelling of concrete beams involving sharp snap-back

Numerical problems are often encountered in modelling crack propagation in concrete beams using non-linear finite element (FE) analysis, especially when sharp snap-back behaviour in load-displacement relations occurs. This paper firstly identifies 16 arc-length control based numerical strategies based on extensive literature review. They are then used to carefully model the structural behaviour of a four-point single notched shear beam using discrete crack modelling approach in which cracks are represented by interface elements with bilinear softening constitutive laws. Based on extensive FE analyses, detailed comparisons of the merits and demerits of these numerical algorithms are then made. The results indicate that the effectiveness and efficiency of different algorithms may vary considerably from one to another, with the local arc-length based procedures in conjunction with tangential stiffness strategy and reversible unloading model being the most robust.     

Experimental Investigation of FRP-Strengthened RC Beam-Column Joints

The results of a comprehensive experimental program, aimed at providing a fundamental understanding of the behavior of shear-critical exterior reinforced concrete (RC) joints strengthened with fiber reinforced polymers (FRP) under simulated seismic load, are presented in this study. The role of various parameters on the effectiveness of FRP is examined through 2/3-scale testing of 18 exterior RC joints. Conclusions are drawn on the basis of certain load versus imposed displacement response characteristics, comprising the strength (maximum lateral load), the stiffness, and the cumulative energy dissipation capacity. The results demonstrate the important role of mechanical anchorages in limiting premature debonding, and they provide important information on the role of various parameters, including: area fraction of FRP; distribution of FRP between the beam and the column; column axial load; internal joint (steel) reinforcement; initial damage; carbon versus glass fibers; sheets versus strips; and effect of transverse beams.