排风扇前盖注射模设计

分析了排风扇前盖塑件的工艺特点,介绍了排风扇前盖注射成型模结构及模具的工作过程。     

Flame Front Deformation Instabilities of Filtration Combustion for Initial Thermal Perturbation

The flame front deformation instability of low-velocity filtration combustion within an inert packed bed is studied based on the initial preheating non-uniformity. Based on the experimental phenomena, an initial thermal perturbation model is numerically proposed so as to predict the deformation behaviors of the flame front instabilities. The numerical prediction indicates that the assumption of an initial thermal perturbation is a feasible explanation as the cause of the flame front inclination instability. As the initial thermal perturbation increases, the phenomena of the flame front break and shrinking instabilities could easily occur at high filtration velocity or low equivalence ratio. Moreover, the evolutions of the flame front break rate and the shrinking rate are quantitatively analyzed.     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

Numerical Study of Finite Element Method Based Solutions for Propagation of Wetting Fronts in Unsaturated Soil

The accurate prediction of the propagation of a wetting front in an unsaturated soil subjected to surficial infiltration is of practical importance to many geotechnical and geoenvironmental problems. The finite element method is the most common solution technique as the hydraulic soil properties are highly nonlinear. Two important issues are often found to create difficulties in such analyses. First, numerical oscillations are usually observed in the calculated pore pressures at the wetting front. Second, when a reasonable mesh size and time step are used, the elevation of the wetting front may be seriously overpredicted. This paper is focused on the second issue. The under-relaxation (UR) technique used in the iterative process within each time step is found to have a serious impact on rate of convergence with refinement in mesh size and time step. Two different techniques are typically used; the first evaluates the hydraulic conductivity using an average of heads calculated from the preceding time node and the most recent iteration of the current time node (UR1), and the second evaluates the hydraulic conductivity using the average of heads calculated from the two most recent iterations of the current time nodes (UR2). The study shows that UR1, which is adopted in programs such as SEEP/W, ensures that the solution converges rapidly to a stable solution within a time step, but may converge to the wrong wetting front at a given elapsed time unless a sufficiently refined mesh is used. UR2 converges much more slowly within a time step, but the error in the wetting front is smaller than that generated by UR1.     

AutoCAD 下非结构网格自动生成

在AutoCAD环境下，从背景网格生成和数据结构两方面对推进阵面法进行修正。采用修理后的方法，使得在流场、泥沙输移和床面冲淤数值计算的前处理过程中无须精心预设内部控制点而只需给边界一个尺度，就能自动生成适应任意复杂边界的非结构网格，从而提高网格生成、优化的效率和通用性。     

Estimation of Width and Depth of the Wetted Soil Volume Under a Surface Emitter,Considering Root Water-Uptake and Evaporation

A cylindrical flow model that describes local infiltration from a surface point source, by incorporating evaporation and water extraction by roots, was used to obtain numerical results that were the base for the development and testing of an empirical method for determining the surface and vertical components of the wetting front. The implementation of the mathematical model took place against two of the twelve USDA soil classes, using three water application rates for each one. The empirical methodology consisted of two simple, time dependent empirical relationships: a power law for the stage of the infiltration, which was applied in both directions and a polynomial for the stage after the end of the irrigation, applied only for the vertical component, to account for percolation losses. The statistical criteria used for the evaluation of the method showed good agreement between the numerical results and the values calculated by the empirical relationships. Based on the limited availability of necessary experimental data for detailed analysis of multidimensional transient infiltration, the introduction of such an empirical model, as a design tool for trickle irrigation systems, may contribute to the selection of the optimum application rate and lateral spacing.     

Geometric features of the flame propagation process for an SI engine having dual‐ignition system

Flame front surface area and enflamed volume (the volume enclosed with flame front) is theoretically analysed for a spark‐ignition engine, having cylindrical disc‐shaped combustion chamber with two spark plugs located axisymmetrically on cylinder head, between cylinder axis and cylinder wall. Spherical flame front assumption is used. A computer code is developed based on purely geometric consideration of the flame development process in combustion chamber, and is used to investigate the effects of variations of spark plugs' locations on geometric features of the flame front. A comparison has also been made with a spark‐ignition engine having one spark plug at the same location. Copyright © 2002 John Wiley & Sons, Ltd.     

铸造Ti—0.2Pd合金SF—1000双级风机叶轮的研制

Ｔｉ－０．２Ｐｄ合金ＳＦ－１０００双级风机叶轮是大型盐酸再生设备的主要部件，采用整体铸造方法制造，无论在技术上还是经济上都是十分有利的。本文主要介绍采用加工石墨，铸铁组合型，真空电弧凝壳熔炼铸造工艺，成功地研制出整体铸造风机叶轮。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Evaluation of Textile Bobbins Drying Processes: Experimental and Modelling Studies

Drying of textile bobbins was carried out on two kinds of laboratory-scale dryers: in a cross circulation drying rig, atmospheric pressure heating air is used, while in the through circulation drying apparatus, the heating air is pressurized before the drying process takes place. In both cases, a bobbin was fitted with seven thermocouples, placed in a plane normal to the bobbin axis but at different radial distances, in order to provide temperature data during the drying process. In cross circulation drying, plots of temperature against time indicated the presence of two moving fronts, one starting from inside the bobbin, another from the outside, while in through circulation drying, similar plots showed the presence of an evaporation front, moving from inside the bobbin to the outside. In both canes, numerical models were developed to simulate the drying processes.