Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Synthesis and characterization of a long side-chain double-cation crosslinked anion-exchange membrane based on poly(styrene-b-(ethylene-co-butylene)-b-styrene)

By choosing a triple block polymer, poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS), as the backbone and adopting a long side-chain double-cation crosslinking strategy, a series of SEBS-based anion-exchange membranes (AEMs) was successively synthesized by chloromethylation, quaternization, crosslinking, solution casting, and alkalization. The 70C16-SEBS-TMHDA membrane showed high OH⁻ conductivity (72.13 mS/cm at 80 °C) and excellent alkali stability (only 10.86% degradation in OH⁻ conductivity after soaking in 4-M NaOH for 1700 h at 80 °C). Furthermore, the SR was only 9.3% at 80 °C and the peak power density of the H₂/O₂ single cell was up to 189 mW/cm² at a current density of 350 mA/cm² at 80 °C. By introducing long flexible side chains into a polymer SEBS backbone, the structure of the hydrophilic–hydrophobic microphase separation in the membrane was constructed to improve the ionic conductivity. Additionally, network crosslinked structure improved dimensional stability and mechanical properties.     

排风扇前盖注射模设计

分析了排风扇前盖塑件的工艺特点,介绍了排风扇前盖注射成型模结构及模具的工作过程。     

上保护层开采底板破坏深度和应力分析研究

上保护层开采导致的底板变形、应力释放会使被保护层内高瓦斯沿着上覆岩层内形成的空隙裂隙结构向上运移，很容易造成所采工作面采空区内瓦斯增加，造成工作面瓦斯超限。以峰峰集团以黄沙矿为研究实例，针对其主采的2号煤层利用FLAC^3D模拟软件进行上保护层开采底板应力研究，揭示了上保护层开采底板应力的规律特性，对于保护层开采工作瓦斯治理具有一定的指导意义。     

浅谈压延铜箔光面色差的成因

针对压延铜箔在表面处理过程中光面易出现色差的问题,从设备、工艺、人员操作等方面进行成因探讨,并给出了应对措施。     

关于硬件木马电路检测技术分析及发展趋势探讨

本文结合HTH电路的复杂性等特征分析与实际应用现状,研究了HTH电路的具体检测技术方法并对当前热点技术进行对比分析,探讨了HTH电路检测方法的技术发展趋势。     

宏阳煤矿薄煤层沿空留巷实践应用

为了缓解矿井采掘接替紧张局面,宏阳煤矿采用沿空留巷技术,对12102运输顺槽采取顶板超前采面打设锚索梁、顶板超前预裂爆破,留巷段采用“钢梁+单体液压支柱”的方式进行巷道支护。该技术现场应用后,减少了巷道掘进工程量,减少了煤炭损失,增加了经济效益,降低了职工劳动强度,有利于采掘接替。     

Corrosion behavior of under‐, peak‐, and over‐aged 6063 alloy: A comparative study

The mechanical property of age‐hardenable Al‐alloys is governed by the state of ageing, which determines the microstructure and consequently, their corrosion behavior which is a vital aspect for a number of applications. This article presents a comparative assessment of corrosion behavior of under‐, peak‐ and over‐aged Al‐Mg‐Si alloy. Corrosion characteristics have been determined via immersion tests in 0.1 M ortho‐phosphoric acid solution and intergranular corrosion (IGC) tests. Corroded surfaces are examined by field emission scanning electron micrographs‐energy dispersive spectroscopy and 3D optical profilometer. The obtained results reveal that the corrosion rate at a specific immersion time as well as the depth of IGC increases in the order for under‐, peak‐, and over‐aged states. Irrespective of the state of ageing, corrosion loss increases linearly but the rate of corrosion decreases rapidly with increasing immersion time. The dominant mode of corrosion in under‐aged alloy is identified as localized pitting, while peak‐aged is highly susceptible to IGC in contrast extensive pitting corrosion is observed for over‐aged alloy. The observed differences in corrosion behavior are explained considering characteristics of precipitates. Formation of β (Mg₂Si) in case of over‐aged alloy and presence of inclusions like AlFeMnSi particles are found to accelerate pitting corrosion.     

多运营商高铁隧道移动网络覆盖方案

高铁移动网络覆盖是国内三大通信运营商的一个重点,而高铁隧道内移动网络覆盖更是运营商的一大难点痛点。文章根据我国中部省份某高铁线路覆盖规划实例,采用“设备+POI+泄漏电缆”模式,即三家运营商信号源设备通过同一POI(point of interface,多系统接入平台)接入,信号输出到泄漏电缆进行隧道覆盖,隧道口场坪站安装宽频切换天线对隧道外进行延伸覆盖,通过链路预算合理布置各运营商主设备信号源,从而实现隧道到室外的无缝覆盖。最后,根据已有成熟网络覆盖解决方案,对未来5G高铁隧道移动网络覆盖方案进行了探讨。     

基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。