Realization of 1 μm thick,crack-free and smooth PMN-PT film in the MPB through PLD: A comprehensive study

This paper presents a comprehensive study on the various hurdles and solutions in the realization of phase pure, pinhole-free and crack-free, 0.65PMN-0.35PT/LSCO/Pt/TiO₂/SiO₂/Si heterostructures using pulsed laser deposition. A few major inquiries were i) effect of excess PbO in the target, ii) modulation of deposition and annealing temperatures for the growth of LSCO buffer layer, iii) thickness of the buffer layer iv) effect of the flow of oxygen in the chamber during and after deposition and v) the annealing conditions; on the phase formation, morphology and leakage response demonstrated by the films. Ferroelectric response parameters viz. P_sat = 47.7 μC/cm², P_r = 20.03 μC/cm², E_C = 62.03 kV/cm and absolute area = 21460 units attest the quality of the grown film.     

One-step synthesis of high purity ZnO micro/nanostructures from pure Zn and pre-alloyed brass powders by vapor phase transport

In this research, vapor phase transport (VPT) was introduced as a facile, inexpensive method to produce ZnO micro/nanostructures from various Zn sources such as pure Zn and alpha brass pre-alloyed powders (Cu–20Zn and Cu–28Zn) at different processing temperatures of 930 °C–1050 °C. Simultaneous thermal analysis (STA) was carried out to investigate Zn evaporation and ZnO micro/nanostructure formation. STA results showed an exothermic peck at 711 °C and 728 °C for Cu–20Zn and Cu–28Zn, respectively, due to oxidation of the evaporated Zn element and formation of ZnO micro/nanostructures. X-ray diffraction results showed that high purity ZnO micro/nanostructures were successfully synthesized via VPT process and the crystallite size was increased from ~60 nm to ~100 nm with increasing processing temperature. Field emission scanning electron microscopy observations showed morphology (e.g. rods, column, tetrapods, and combs) and size of the synthesized micro/nanostructures were dependent on the Zn sources and processing temperature, in which average diameter of the synthesized ZnO structures was increased with increasing the processing temperature. The smallest (98 nm) and largest (603 nm) average diameters of synthesized ZnO micro/nanostructures were attained from the pure Zn and Cu–28Zn brass powders at 930 °C and 1050 °C, respectively.     

Atomic layer chemical vapour deposition of copper

Copper films with (1 1 1) texture are of crucial importance in integrated circuit interconnects. We have deposited strongly (1 1 1)-textured thin films of copper by atomic layer deposition (ALD) using [2,2,6,6-tetramethyl-3,5-heptadionato] Cu(II), Cu(thd)₂, as the precursor. The dependence of the microstructure of the films on ALD conditions, such as the number of ALD cycles and the deposition temperature was studied by X-ray diffraction, scanning electron microscopy (SEM), and transmission electron microscopy. Analysis of (1 1 1)-textured films shows the presence of twin planes in the copper grains throughout the films. SEM shows a labyrinthine structure of highly connected, large grains developing as film thickness increases. This leads to low resistivity and suggests high resistance to electromigration.     

Nanostructured polymer blends: Synthesis and structure

Nanostructured polymer blends prepared via anionic ring opening polymerizations of cyclic monomers in the presence of a pre-made polymer melt exhibit a number of special properties over traditional polymer blends and homopolymers. Here, we report on a simple and versatile method of in situ polymerization of macrocyclic carbonates in the presence of a maleic anhydride polypropylene (mPP) matrix and a surface-active compatibilizer (i.e. PC grafted onto a mPP backbone generated in situ) to yield a micro- and nanostructured polymer blends consisting of a polycarbonate (PC) minor phase, and a polypropylene (PP) major phase. By varying the processing conditions and concentration of the macrocyclic carbonate it was possible to reduce the size of the PC dispersions to an average minor diameter of 150 nm. NMR and TEM characterizations indicate that the PC dispersions do not influence crystal content in the PP phase. Overall, the results point to a simple strategy and versatile route to new polymeric materials with enhanced benefits.     

Dynamic vulcanisation of EPDM/PE-based thermoplastic vulcanisates studied along the extruder axis

Simple blending and dynamic vulcanisation of EPDM/PE blends using the resol/SnCl₂ system was studied in an extruder using a series of sampling devices. The melting of the PE pellets occurs just in front of and in the first kneading zone. Upon complete melting of the PE phase, the EPDM/PE blends reach very quickly their final morphology. Crosslinking of the EPDM phase to high levels occurs already when the PE phase is not yet fully molten. The higher the EPDM content, the higher the viscous dissipation, the higher the melt temperature and, consequently, the higher the crosslinking rate. For the EPDM/PE (50/50; w/w) TPV a transition from continuous via co-continuous to fully dispersed EPDM is observed, which is driven by crosslinking. Although the degree of crosslinking of the EPDM rubber is very high, this does not prevent phase inversion of the blend. The EPDM/PE interface is rather blurred, because PE crystalline lamellae are growing into the EPDM domains, probably because of the high compatibility between PE and EPDM (60 wt% of ethene). This study shows that dynamic vulcanisation in extruders proceeds quite differently from that in batch kneaders, where melting, mixing and crosslinking are separated in time. In extruders mass and heat transport, melting of the thermoplastic, morphology development (including dispersion and phase inversion), distribution and dissolution of (crosslinking) chemicals and crosslinking of the rubber do not occur as independent phenomena, but mutually and/or continuously interact.     

Development of co-continuous structure in liquid crystalline polyester

We investigated liquid crystallization of liquid crystalline polyester BB-5 during isothermal annealing by digital high-fidelity microscope and light scattering. A liquid crystalline spherical domain having a radius of micrometers appeared by annealing at around 180 °C. The domain grew dendritically in all directions. Neighboring liquid crystalline regions coalesced and then interconnected. The interconnected structure changed to a co-continuous two-phase structure with increasing ordering of the liquid crystalline phase, and the interface between the liquid crystalline phase and the isotropic phase became smoother over time. Liquid crystallization stopped before volume filling the whole space, and the liquid crystalline phase and isotropic phase coexisted. The liquid crystalline region became narrower with an increase in the temperature of the liquid crystallization. Such structural development is different from the liquid-liquid phase separation via spinodal decomposition, and it may be attributed to the segregation of non-liquid crystallizable low molecular weight molecules from the growth front by fractionation of the molecular weight distribution during the liquid crystallization in terms of the instability of the diffusion-controlled interface.     

ABS／PC／MMA类共聚物Q三元共混体系的性能和形态

本文研究了ABS/PC甲基丙烯酸甲酯(MMA)共聚物Q三元共混物的性能与Q含量的关系,对不同Q含量下共混物的拉伸、冲击、弯曲、耐热、熔体指数等性能进行了测试,并用扫描电镜观察了该三元共混物的形态。结果表明,加入共聚物Q可增加共混体系的相容性,在适当组成下可使共混物的弯曲强度提高到原来的1.7倍,同时其他力学性能有所提高或不受损失;共混物的熔体指数能符合工业生产要求。从经济角度看,Q价格也较低。因而ABS/PC/Q三元共混物可望开发为具有重要实际意义的塑料合金。     

Effect of pH on the Crystallization of Homogeneously Precipitated Nanosized PZT Powder

Nanosized lead zirconate titanate (PZT) powder with Zr:Ti ratio in the morphotropic phase boundary region was synthesized by homogeneous precipitation of metal ions. The powder precipitated at 90°C and at pH 6.7 resulted single-phase perovskite lead zirconate titanate powder when calcined at 550°C and above for 4 hours in air. The solution pH and the precipitation temperature strongly affect the composition of the calcined powder. The results obtained by structural characterization of homogeneously precipitated powder were compared with that obtained from the conventional precipitation method using ammonia in terms of crystallization, homogeneity, and microstructure. The homogeneously precipitated powder showed smaller particle size, minimum agglomeration and uniform shape on calcination and annealing. Powdered samples that precipitated by homogeneous precipitation crystallized directly to perovskite PZT, without any intermediate pyrochlore phase formation. In contrast, the NH₃ precipitated powder converted to perovskite PZT via metastable pyrochlore and it showed phase segregation upon annealing at higher temperatures. The reaction kinetics has been studied by X-ray diffraction, differential thermal analysis, and differential scanning calorimetry.     

EPDM/PP热塑性弹性体相态研究

采用透射电镜(TEM)研究动态硫化EPDM/PP热塑性弹性体制备工艺及增容改性对形态结构的影响,研究发现通过添加增容剂可使EPDM相呈颗粒分布于连续相中。     

Evaluation of Morphology—Stable Critical Size of KNbO3 Crystals

Skeletal form of KnbO3 crystals growing in Li2B4O7 solvent was in-situ observed at 900℃ and it was found that shallow depression started to develop on the surface of KnbO3 crystals when the crystal size exceeded several micron,typically 7 micron.Based on the quantitative criterion derived by Chernov,the estimated critical size of KNbO3 crystals was 1 micron,which was consistent with the experimental measurement.The kinetic coefficients,Kcorner and Kcr,in the criterion were experimentally obtained in the diffusive-convective and diffusive-advective flow states respectively.