Optical design of the Lyman alpha based beam emission spectroscopy(LAB)diagnostic on the HL-2A tokamak

In this article, we present the optical design of a novel diagnostic on the HL-2 A tokamak, i.e. the20-channel edge Lyman-alpha beam emission spectroscopy, which is a promising solution for edge density turbulence research on tokamaks, as it offers the possibility of density fluctuation measurement with a 3.3 mm spatial resolution while maintains a high temporal resolution of1 μs. The optical path, including the reflective collection optics, the high-dispersion spectrometer, and the linear detector array, is carefully optimized to obtain a good image quality and a high throughput. The maximum root mean square radius of the collection optics is 64 μm.The detected photon flux is estimated to be about 10~(11) photons/s/channel.     

Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

基于阶段注意力机制的电力线提取算法

电力系统维护是电力系统稳定运行的重要保障，应用智能算法的无人机电力巡检则为电力系统维护提供便捷。电力线提取是自主电力巡检以及保障飞行器低空飞行安全的关键技术，结合深度学习理论进行电力线提取是电力巡检的重要突破点。本文将深度学习方法用于电力线提取任务，结合电力线图像特点嵌入改进的图像输入策略和注意力模块，提出一种基于阶段注意力机制的电力线提取模型（SA-Unet）。本文提出的SA-Unet模型编码阶段采用阶段输入融合策略（Stage input fusion strategy， SIFS），充分利用图像的多尺度信息减少空间位置信息丢失。解码阶段通过嵌入阶段注意力模块（Stage attention module，SAM）聚焦电力线特征，从大量信息中快速筛选出高价值信息。实验结果表明，该方法在复杂背景的多场景中具有良好的性能。     

Metal chlorides-promoted ammonia absorption of deep eutectic solvent

Ammonia is considered as a promising hydrogen or energy carrier. Ammonia absorption or adsorption is an important aspect for both ammonia removal, storage and separation applications. To these ends, a wide range of solid and liquid sorbents have been investigated. Among these, the deep eutectic solvent (DES) is emerging as a promising class of ammonia absorbers. Herein, we report a novel type of DES, i.e., metal-containing DESs for ammonia absorption. Specifically, the NH₃ absorption capacity is enhanced by ca. 18.1–36.9% when a small amount of metal chlorides, such as MgCl₂, MnCl₂ etc., are added into a DES composed of resorcinol (Res) and ethylene glycol (EG). To our knowledge, the MgCl₂/Res/EG (0.1:1:2) DES outperforms most of the reported DESs. The excellent NH₃ absorption performances of metal–containing DESs have been attributed to the synergy of Lewis acid–base and hydrogen bonding interactions. Additionally, good reversibility and high NH₃/CO₂ selectivity are achieved over the MgCl₂/Res/EG (0.1:1:2) DES, which enables it to be a potential NH₃ absorber for further investigations.     

超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

Structural modification of aminoclay for catalytic applications

Abstract

An eco-friendly catalyst system was synthesized using three step reaction. The Cu nanoparticles bridged aminoclay catalyst was analyzed using various analytical techniques. The structure of the catalyst was confirmed by FTIR and XRD. The synthesized catalyst system was used for the reduction of p-nitrophenol (NP), Cr(VI), and fluorescein (Flur) dye individually, as well as in their mixture forms. The k_app value was computed to access the efficiency of the catalyst. The results indicated that the k_app value of the individual system is higher than that of the mixture systems due to the absence of the complex formation reaction. The catalytic performance of the catalyst was also tested for the Schiff base (SB) formation between poly(ethyleneglycol) (PEG) and aniline (ANI) in an oxygen atmosphere. The ¹H-NMR spectroscopy result indicates that the present catalyst system produced 86% yield.     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.     

无人机在输电线路巡检中的多种应用

无人机技术目前的快速发展使得我们国家输电线路自身的巡检能力得到了持续的提升,基于此本文在对无人机技术给予认识的情况下,在了解了输电线路巡检过程中的使用优势之后,还总结了无人机技术在当前我国线路巡检过程中的应用路径以及应用方法;之后使用案例分析的方式分析了无人机技术在当前输电线路巡检过程中的应用方法。     

Sustainable disassembly line balancing model based on triple bottom line

End of life (EOL) phase of a product is receiving more attention due to increase in environmental concerns, and many studies have been conducted for value creation in EOL, focusing on concepts as remanufacturing, reuse and recycling in sustainable production manner. This study especially focuses on one of global problem, e-waste. To minimise the amount of wastes and maximise recovered materials from EOL, disassembly is one of the most important concept, associated with reuse, and balancing disassembly line in an optimal way is essential for organisations. In disassembly line balancing (DLB), not only precedence of tasks, but also risk criteria related to environment and human safety should be considered for sustainability. The aim of this study is to propose a model based on triple bottom line (TBL) dimensions, i.e. human safety, environmental safety and business criteria. To achieve sustainability in DLB, and for risk assessment in sustainable DLB, it had been decided to use a multi-criteria method, i.e. TODIM, acronym in Portuguese of ‘Tomada de Decisão Iterativa Multicritério’. The proposed model included 22 disassembly criteria categorised under TBL dimensions, which are derived from the literature. Implementation of the study was conducted for computer disassembly processes, and as a result of the study approximately 12% an improvement in cycle time was succeeded. In the long run, the integration of sustainability in disassembly operations may contribute to the competitive advantage of the company in terms of differentiation and corporate image by achieving business, environment and human targets simultaneously.     

A novel fast distance relay for series compensated transmission lines

This paper presents a fast distance relay for series compensated transmission lines based on the R–L differential-equation algorithm using the theory of equal transfer process of transmission lines. The measuring distances based on the proposed algorithm can fast approach the actual value of fault distance when a fault occurs in front of the series capacitor. When a fault occurs behind of the series capacitor, the fault loop, including the series capacitor, does not match the R–L transmission line model, so the measuring distances fluctuate severely. Based on this, the relative position of the fault with respect to the series capacitor can be judged effectively according to the fluctuation range of the measuring distances, and the accurate fault location can be obtained fast. A variety of PSCAD/EMTDC simulation tests show that the new relay has fast operating speed and high accuracy when applied to the long series compensated transmission lines.