Diluted chemical bath deposition of CdZnS as prospective buffer layer in CIGS solar cell

In this study, dilute chemical bath deposition technique has been used to deposit CdZnS thin films on soda-lime glass substrates. The structural, morphological, optoelectronic properties of as-grown films have been investigated as a function of different Zn²⁺ precursor concentrations. The X-ray diffractogram of CdS thin-film reveals a peak corresponding to (002) plane with wurtzite structure, and the peak shift has been observed with the increase of the Zn²⁺ concentration upon formation of CdZnS thin film. From morphological studies, it has been revealed that the diluted chemical bath deposition technique provides homogeneous distribution of film on the substrate even at a lower concentration of Zn²⁺. Optical characterization has shown that the transparency of the film is influenced by Zn²⁺ concentration and when the Zn²⁺ concentration is varied from 0 M to 0.0256 M, bandgap values of resulting films range from 2.42 eV to 3.90 eV while. Furthermore, electrical properties have shown that with increasing zinc concentration the resistivity of the film increases. Finally, numerical simulation validates and suggests that CdZnS buffer layer with composition of 0.0032 M Zn²⁺ concentration would be a promising candidate in CIGS solar cell.     

Structural silicone sealants after exposure to laboratory test for durability assessment

During the service life of structural sealant glazing (SSG) facades, the load-bearing capacity of the silicone bonds needs to be guaranteed. Laboratory tests can assess the durability of SSG-systems based on mechanical characteristics of the bond after simultaneous exposure to both climatic and mechanical loads. This article studies how the material characteristics of two common structural sealants are affected by laboratory and field exposure. Dynamic mechanical analysis (DMA) confirms a reduction in the dynamic modulus of exposed silicone samples. Results from thermogravimetric analysis, Fourier-transform infrared spectroscopy, differential scanning calorimetry, and small-angle X-ray scattering/wide-angle X-ray scattering show differences between the two sealants and indicate no/minor changes in the composition and morphology of the laboratory and field exposed sealants. Mechanical characterization methods, such as DMA, and tensile and shear testing of the structural bond, are shown to be sensitive toward the combined climatic and mechanical loadings, and are hence suitable for studying degradation mechanisms of structural sealants.     

Influence of temperature on acoustic emission source location accuracy in underground structure

An acoustic emission (AE) experiment was carried out to explore the AE location accuracy influenced by temperature. A hollow hemispherical specimen was used to simulate common underground structures. In the process of heating with the flame, the pulse signal of constant frequency was stimulated as an AE source. Then AE signals received by each sensor were collected and used for comparing localization accuracy at different temperatures. Results show that location errors of AE keep the same phenomenon in the early and middle heating stages. In the later stage of heating, location errors of AE increase sharply due to the appearance of cracks. This provides some beneficial suggestions on decreasing location errors of structural cracks caused by temperature and improves the ability of underground structure disaster prevention and control.     

Structural analysis and optimization of a tethered swept wing for airborne wind energy generation

In this paper, we present an aero‐structural model of a tethered swept wing for airborne wind energy generation. The carbon composite wing has neither fuselage nor actuated aerodynamic control surfaces and is controlled entirely from the ground using three separate tethers. The computational model is efficient enough to be used for weight optimisation at the initial design stage. The main load‐bearing wing component is a nontypical “D”‐shaped wing‐box, which is represented as a slender carbon composite shell and further idealised as a stack of two‐dimensional cross section models arranged along an anisotropic one‐dimensional beam model. This reduced 2+1D finite element model is then combined with a nonlinear vortex step method that determines the aerodynamic load. A bridle model is utilised to calculate the individual forces as a function of the aerodynamic load in the bridle lines that connect the main tether to the wing. The entire computational model is used to explore the influence of the bride on the D‐box structure. Considering a reference D‐box design along with a reference aerodynamic load case, the structural response is analysed for typical bridle configurations. Subsequently, an optimisation of the internal geometry and laminate fibre orientations is carried out using the structural computation models, for a fixed aerodynamic and bridle configuration. Aiming at a minimal weight of the wing structure, we find that for the typical load case of the system, an overall weight savings of approximately 20% can be achieved compared with the initial reference design.     

Note of Caution for the Aqueous Behaviour of Metal-Based Drug Candidates

Poor aqueous solubility is one of the recurrent drawbacks of many compounds in medicinal chemistry. To overcome this limitation, the dilution of drug candidates from stock solutions of an organic solvent is common practice. However, the precise characterisation of these compounds in aqueous solutions is often neglected, leading to some uncertainties regarding the nature of the actual active species. In this communication, we demonstrate that two ruthenium complexes previously reported by our group for their chemotherapeutic potential against cancer, namely [Ru(DIP)₂(sq)](PF₆) and [Ru(DIP)₂(3-methoxysq)](PF₆), where DIP is 4,7-diphenyl-1,10-phenanthroline, sq=semiquinonate and 3-methoxysq=3-methoxysemiquinonate, form colloids in water-DMSO (1 % v/v) mixtures that are invisible to the naked eyes. [Ru(DIP)₂(3-methoxysq)](PF₆) was found to form a highly stable and monodispersed colloid with nanoaggregates of ∼25 nm. In contrast, [Ru(DIP)₂(sq)](PF₆) was found to form large reticulates of mostly spherical aggregates which size was found to increase over time. The difference in size and shape distribution of drug candidates is of tremendous significance as the study of their biological activity might be severely affected. Overall, we strongly believe that these observations should be taken into account by the scientific community working on the development of metal-based drugs with poor water solubility.     

Continuous Flow Fabrication of Block Copolymer–Grafted Silica Micro‐Particles in Environmentally Friendly Water/Ethanol Media

Polymer‐grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface‐initiated controlled radical polymerization (SI‐CRP) is the most feasible method to fabricate PGIPs. However, a conventional in‐batch reaction still suffers from several disadvantages, including time‐consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)‐b‐poly(N‐isopropylacrylamide) (PNIPAM)–grafted silica micro‐particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI‐CRP can be accomplished sequentially in a continuous flow system, avoiding multi‐step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (Р< 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in‐batch reaction at the same condition, the continuous system also suppresses possible gelation problems.     

开关磁阻电机结构性转矩脉动抑制方法

开关磁阻电机具有结构简单、成本低和调速范围广等优势,但其双凸极结构和控制器的开关特性,导致存在转矩脉动现象,使得抑制转矩脉动成为焦点问题。首先从开关磁阻电机的结构和运行机理出发,针对线性解析方法难以分析转矩特征的问题,建立电机有限元模型求解出转矩特征并进行样机验证试验。分析样机结构参数对转矩脉动的影响,针对结构参数耦合问题,选择NSGA-Ⅱ算法在参数优化平台上对样机结构参数进行多目标寻优,在保证优化后样机的转矩脉动系数和平均转矩均优于初始电机的条件下,最终获得样机最优化结果。结果表明,不同结构参数对电机转矩的影响有较大的差异,对结构参数的优化能有效地抑制转矩脉动,该参数优化方法可以为开关磁阻电机结构性转矩脉动抑制提供参考。     

以有机化学课程内容为引导，加强课程思政的探索与实践

有机化学是化学化工、材料、制药、食品等多个专业的基础课程,在其教学过程中,教师可以根据课程的内容及特点,分别以有机化学发展中的重大历史事件、有机化物的性质及有机反应为引导,开展学生的思想品德教育,加强课程思政建设。     

社交网络中基于网络结构支撑模型的谣言传播研究

结合结构支撑理论，探究节点网络结构支持力的一些性质，提出了社交网络结构中的全网支持力和被支持力的总量一致性，并进一步提出计算节点支持力的方法。谣言作为特殊信息，在支持力不同节点之间的传播特性有所不同，借鉴随机游走模型中的PageRank计算方法，对不同节点支持力的谣言传播以及传播后的辟谣状况进行了仿真模拟，结果表明支持力不同的节点对于谣言传播和辟谣影响明显。