Double emulsion (W/O/W) gel stabilised by polyglycerol polyricinoleate and calcium caseinate as mangiferin carrier: insights on formulation and stability properties

Mangiferin (MGF) is a phenolic compound isolated from mango, but its poor solubility significantly limits its use. In this study, MGF was embedded into the inner aqueous phase of W₁/O/W₂ emulsions. Firstly, the dissolution method of MGF was determined. MGF remained stable in solution with pH 13 at 30 min, and its solubility reached 10 mg mL⁻¹. When the pH of MGF solutions was adjusted from pH 13 to pH 6, MGF did not immediately crystallise, providing sufficient time to construct the MGF-loaded W₁/O/W₂ emulsions. Subsequently, the MGF-loaded W₁/O/W₂ emulsions were constructed using polyglycerol polyricinoleate (PGPR) and calcium caseinate (CAS). The formation and stability of the W₁/O/W₂ emulsions were investigated. The MGF-loaded W₁/O/W₂ emulsions stabilised with 1% PGPR and 1% – 3% CAS exhibited a low viscosity, limited loading capacity, and poor stability. Conversely, the MGF-loaded W₁/O/W₂ emulsions stabilised by 3%PGPR–3%CAS exhibited optimal loading capacity (encapsulation efficiency = 95.31% and loading efficiency = 0.91%) and stability, which was attributed to the fact that high viscosity and gel state retarded the migration of inner aqueous phase. These results indicated that the W₁/O/W₂ emulsions stabilised by PGPR and CAS may be a potential alternative for encapsulating mangiferin.     

Nano fibrillated cellulose-based foam by Pickering emulsion: Preparation,characterizations, and application as dye adsorbent

An ecofriendly and biodegradable porous structure was prepared from drying aqueous foams based on nano fibrillated cellulose (NFC), extracted from softwood pulp by subcritical water/CO₂ treatment (SC-NFC). The primary aim of this work was to use the modified SC-NFC as stabilizer for a water-based Pickering emulsion which upon drying, yielded porous cellulosic materials, a good dye adsorbent. In order to exploit the carboxymethylated SC-NFC (CMSC-NFC, with a degree of substitution of 0.35 and a charge density of 649 μeqv/g) as a stabilizer for water-based Pickering emulsion in subsequent step, an optimized quantity of octyl amine (30 mg/g of SC-NFC) was added to make them partially hydrophobic. A series of dry foam structures were prepared by varying the concentrations of treated CMSC-NFCs and 4 wt% was found to be the optimum concentration to yield foam with high porosity (99%) and low density (0.038 g/cc) along with high compression strength (0.24 MPa), superior to the conventionally extracted NFC. The foams were applied to capture as high as 98% of methylene blue dyes, making them a potential green candidate for treating industrial effluent. In addition, the dye adsorption kinetics and isotherms were found to be well suited with second order kinetics and Langmuir isotherm models.     

Material encapsulation in poly(methyl methacrylate) shell: A review

Material encapsulation is a relatively new technique for coating a micro/nanosize particle or droplet with polymeric or inorganic shell. Encapsulation technology has many applications in various fields including drug delivery, cosmetic, agriculture, thermal energy storage, textile, and self-healing polymers. Poly(methyl methacrylate) (PMMA) is widely used as shell material in encapsulation due to its high chemical stability, biocompatibility, nontoxicity, and good mechanical properties. The main approach for micro/nanoencapsulation of materials using PMMA as shell comprises emulsion-based techniques such as emulsion polymerization and solvent evaporation from oil-in-water emulsion. In the present review, we first focus on the encapsulation techniques of liquid materials with PMMA shell by analyzing the effective processing parameters influencing the preparation of PMMA micro/nanocapsules. We then describe the morphology of PMMA capsules in emulsion systems according to thermodynamic relations. The techniques to investigation of mechanical properties of capsule shell and the release mechanisms of core material from PMMA capsules were also investigated. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48039.     

脱硫胶粉在乳化改性沥青中的应用

考察了不同规格胶粉及不同脱硫程度的脱硫胶粉对橡胶改性乳化沥青性能的影响,结果表明,采用100目胶粉即可制备出橡胶改性乳化沥青,但乳化沥青的性能较差;采用活化度为50%左右的100目脱硫胶粉制备乳化沥青时,脱硫胶粉的用量相比于胶粉可大幅提高;在通过外掺100目50%左右活化度的脱硫胶粉(质量分数15%,以沥青计,下同)和质量分数2%的苯乙烯-丁二烯-苯乙烯嵌段共聚物改性的乳化沥青中添加质量分数1%的丁苯胶乳,所制备橡胶改性乳化沥青无筛上剩余物,5 d储存稳定性为2.9%,蒸发残留物的25℃针入度、软化点和5℃延度分别为55 (0.1 mm)、64.5℃和22.5 cm,能够满足乳化改性沥青的技术指标要求。     

Microstructure and permeability of porous YSZ ceramics fabricated by freeze casting of oil-in-water suspension

Porous yttria-stabilized zirconia (YSZ) ceramics are fabricated through freeze casting of oil-in-water suspension followed by sintering at 1250−1550 °C. The pore structure, compressive strength and permeability of porous YSZ ceramics are tailored via altering the emulsion content and sintering temperature. The samples obtained using higher emulsion content or at lower sintering temperature show larger Darcian and non-Darcian constants due to their higher open porosity and larger pore size. Furthermore, the investigation on individual contributions of viscous and inertial resistances on the total pressure drop during permeation process indicates that the viscous resistance increases but the inertial resistance decreases with increasing the emulsion content or decreasing the sintering temperature for samples. Porous YSZ ceramics obtained in this work with a k₁ range of 3.14 × 10⁻¹³–1.12 × 10⁻¹² m² are appropriate for applications in filters and membrane supports.     

道路用聚氨酯改性沥青的制备工艺探讨

结合不同改性剂掺量单因素试验,确定了采用88mm叶轮、115mm容器、圆盘锯齿式搅拌器(转速1400r/min)、175℃共混温度、改性剂掺量4.27%、单次搅拌300g的制备工艺参数。在此条件下制备的聚氨酯改性沥青具有优异的水稳定性、储存稳定性且耐老化、耐高温,拥有比普通聚合物改性沥青更高的车辙因子G*/sinδ和15℃动态模量,基本满足高模量沥青要求。     

Influence of HMTA ligand in MMA AGET ATRP emulsion polymerization

Interactions of hexamethylenetetramine ligand in atom transfer radical polymerization initiated by activator generated by electron transfer were studied. Polymerization of methyl methacrylate was done using two-step experimental procedure in 2 L emulsion batch reactor at 50, 60, and 80°C. The selection of reactant ratios was quite challenging for a reactor of this size. Replicate runs were conducted for data reproducibility purpose. Gravimetry method and gel permeation chromatography were used to determine monomer conversion, Mn, and PDI of polymer samples. PMMA produced was also characterized by means of dynamic light scattering, Fourier-transform infrared spectroscopy and nuclear Magnetic Resonance spectroscopy. Results showed high monomer conversion up to 93% and Mn ranging 243–274 kg/mol with PDI from 1.45 to 1.60. Besides, combining HMTA with sodium dodecyl sulfate, an anionic surfactant, a well-controlled polymer with a lower Mn of 201 kg/mol and PDI of 1.56 was obtained in 3 hr reaction time.     

道路用改性石油基彩色沥青的路用性能评价

以克拉玛依优质的低凝环烷基稠油馏分为基础原料，加入填充剂、改性剂等助剂，采用加热搅拌的工艺技术，使各组分很好地熔融为一体，生产出聚合物复合改性的道路用改性石油基彩色沥青系列产品。产品的综合性能超过重交通道路沥青的JTGF40-2004110号A类标准，在关键指标上已达到交通部（JTGF40-2004）的SBS改性沥青I—A标准的要求。对该产品进行的路用性能评价结果表明，所制备的彩色沥青混合料具有良好的水稳定性、高温稳定性、低温抗裂性能和耐紫外线老化性能，各项路用性质满足了彩色铺面的技术要求。     

涂料用纯丙乳液的性能研究

以甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)和甲基丙烯酸(MA)为主要原料,利用半连续乳液聚合工艺,制备了一种涂料用纯丙乳液基料;考察了乳化剂、引发剂用量及pH值对产物性能的影响。结果表明,当w(乳化剂)=3%,w(引发剂)=0.35%,pH在8~9左右时,涂膜的吸水率达到7.9%,残余单体量<0.5%,水稀释稳定性,钙离子稳定性,冻融稳定性均通过测试,纯丙乳液具有较好的综合性能。     

超临界流体萃取技术生产重交通道路沥青的研究

研究了采用超临界流体萃取技术(SFEF),以减压渣油和催化裂化油浆为原料,制备重交通道路沥青产品的可行性.结果表明:当原料中油浆掺入量为10%～30%时,可以生产出牌号为AH70,AH90,AH110的重交通道路沥青产品.工业试验表明,生产牌号为AH70,AH90的重交通道路沥青,采用此技术方案是可行的.