爆炸焊接——热轧双相不锈钢复合钢板研制

本文主要阐述了通过爆炸焊接和热轧的方法,研制成功可焊性良好的且具有较好强度、韧性与综合性能的双相耐应力腐蚀的不锈复合钢板。还将热轧与热处理的两种试验作了较全面的常规、特殊检验试验,结果完全达到使用要求。     

PTA酸化沉淀池的腐蚀及其研究

阐述了ＰＴＡ酸化沉淀池的腐蚀状况、防腐材料的选材试验及防腐措施的研究及其使用效果；分析了Ｍ树脂玻璃钢的应用技术；提出了ＰＴＡ酸化沉淀池采用复合玻璃钢的防腐措施。     

环氧玻璃钢衬里在化工设备中的应用

本文叙述了非标准化工设备的环氧玻璃钢防腐衬里工艺、配方及使用考查结果．     

提高小口径深孔阀门密封面抗高温水蒸气腐蚀性能的研究

设计了一套高温水蒸气腐蚀的试验装置,利用这套装置对比了用于小口矩深孔阀门密封面上的三种焊层的抗高温水蒸气腐蚀性能,这三种焊层分别为：激光熔覆ＷＦ１４１合金层,手工电弧堆焊“丝１１１”和“堆５４７Ｍｏ”合金层。采用金相显微镜、Ｘ射线射仪、扫描电镜和能谱分析仪对腐蚀试样进行了分析,讨论了合金成分、焊层工艺等对密封面高温水蒸气腐蚀行为的影响,结果表明,激光熔覆ＷＦ１４１合金层具有优异的抗高温水蒸气腐蚀性     

Welding current influences on Inconel 625/X65 cladding interface

The pulsed gas tungsten arc welding with hot wire was used to clad Inconel 625 on the surface of X65 steel. The influences of welding current in horizontal welding position on the dilution, in further the composition, microstructure, and property of the Inconel 625/X65 cladding interface were investigated. Experimental results show that with the increase in welding current, namely, in heat input and arc force, dilution rate increased; the composition transition region in the cladding layer close to the fusion line, controlled by the cladding temperature, would be widen; in further, the microstructure would be different due to the heat transfer and composition change; the precipitates were niobium-rich MC carbide with a low welding current, but tended to be the intermetallic compounds, Laves phase, with a high welding current; the highest and lowest hardness values appeared on the heat-affected zone and cladding layer next to the bonding interface, respectively.     

钢内筒钛钢复合板焊接工艺特点

简要介绍了镇江电厂三期工程钢内筒钛钢复合板焊接工艺，及钛钢复合板焊接质量控制要点。     

Mechanical behaviour of surface layer fibreglass-reinforced flexible pavements

The work presented in this paper aims at providing a better understanding of the mechanical response of surface layer fibreglass-reinforced flexible pavements. The surface reinforcement technique consists of installing a fibreglass grid in between the levelling layer (placed on the base course to seal and level the pre-existing distresses) and the wearing course (or overlay). Flexural fracture tests were performed on two-layered reinforced asphalt specimens composed of both levelling and wearing courses to simulate a real overlay structure. Three fibreglass grids characterised by different mechanical and/or geometrical properties were employed. Strain localisation and damage distribution were investigated using an in-house digital image correlation system capable of achieving highly accurate 2D full-field strain maps of the specimens during loading. Finally, an analytical model was developed on purpose to reproduce the mechanical response of the asphalt mixture-interlayer system.     

焊缝层数对不锈钢复合板残余应力和变形的影响

利用有限元法开发顺次耦合的弹塑性焊接残余应力有限元分析程序,对304不锈钢复合板补焊残余应力进行分析;在试验验证的基础上,讨论焊缝层数对残余应力的影响。计算结果表明,最大焊接残余应力出现在热影响区。由于覆材和基材强度的不匹配,在基材和覆材的界面产生了不连续的应力分布,对开裂影响很大。随着焊缝层数增加,变形增加,导致部分残余应力释放,使得残余应力降低。     

Microstructural evolution of AISI 4340 steel during Direct Metal Deposition process

In the current investigation AISI 4340 steel was laser deposited on a rolled mild steel substrate by Direct Metal Deposition (DMD) technology. The microstructural investigation of the clad was performed using optical and electron microscopes and X-ray diffraction techniques. The microstructure consisted of ferrite, martensite and cementite phases. Two types of martensite, lathe-type and plate-type, were observed in the microstructure. Decrease in microhardness values from the top layer to the alloy layer proves that the degree of tempering of the martensite phase increases in the same direction. The lattice parameters of the identified phases were found to be shorter than those reported in literature. The reported parameters in literature are from samples processed under equilibrium conditions.