混合乳化剂的优选及抗高低温水包油钻井液的研制

O/W乳化钻井液用的阴离子/非离子混合乳化剂,其中的非离子乳化剂先用PIT法初选,再以O/W乳状液黏度为性能指标,用HLB法选定,其中的阴离子乳化剂也用HLB法筛选。选定的一对非离子和阴离子乳化剂按不同比例复配,利用混合表面活性剂HLB值的加和性原理,由O/W乳状液黏度-HLB值关系确定二者最佳配比。O/W乳化钻井液以体积比70/30的柴油 原油为油相,油水相体积比40/60-60/40,乳化剂加量为油水总体积的4%-7%,加入的主要处理剂有:一种代替膨润土的成胶剂,抗高温液体抑制剂,油溶性储层保护剂,降滤失剂等。该钻井液在180℃、最高压力2.5 MPa下热处理24小时或在-26℃冷冻24小时后解冻,均不发生破乳,性能不恶化;用-26℃冷冻7天的乳化剂配制的钻井液,常温和热处理后性能良好。该钻井液流变性能良好,动塑比0.23-0.60,静切力2-8/2-10 Pa,滤失量为零,抑制性良好。图1表3参4。     

Encapsulation of PV modules using ethylene vinyl acetate copolymer as a pottant: A critical review

The primary purpose of this work is to review the literature about what is and is not known about using ethylene vinyl acetate (EVA0 copolymer as the encapsulant (or pottant) material in photovoltaic (PV) modules. Secondary purposes include elucidating the complexity of the encapsulation problem, providing an overview about encapsulation of PV cells and modules, providing a historical overview of the relevant research and development on EVA, summarizing performance losses reported for PV systems deployed since ca. 1981, and summarizing the general problems of polymer stability in a solar environment. We also provide a critical review of aspects of reported work for cases that we believe are important.Failure modes resolved in the early work to establish reliability of deployed modules and the purposes and properties of pottants, are summarized. Typical performance losses in large field-deployed, large-scale systems ranging from 1% to 10% per year are given quantitatively, and qualitative reports of EVA discoloration are summarized with respect to ultraviolet (UV), world-wide location and site dependence.The general stability of polymers and their desirable bulk properties for solar utilization are given. The stabilization formulation for EVA, its effectiveness, and changes in it during degradation are discussed. The degradation mechanisms for the base resin, e.g., unstabilized Elvax 150^TM, and stabilized EVA are indicated for literature dating to the early 1950s, and the role played by unsaturated chromophores is indicated. The limited number of studies relating discoloration and PV cell efficiency are summarized.Observed degradation of EVA or the unstabilized base resin in the laboratory and examples used to measure the degradation are summarized in sections entitled: (1) thermally-induced degradation; (2) photodegradation and photothermal degradation of EVA in different temperature regimes; (3) photobleaching and photodegradation of the UV absorber and cross-linking agent; (4) acetic acid and metal and metal-oxide catalyzed oxidative degradation; and (5) discolaration and PV cell efficiency losses.Processing effects/influences on EVA stability are discussed in sections entitled: (1) EVA raw materials and extruded, uncured films; (2) thermal encapsulation processes; (3) effects of lamination, curing, and curing peroxide on gel content and chromophores formed; and (4) incomplete shielding of curing-generated chromophores. A summary is given for the limited number of accelerated lifetime testing efforts and examples of erroneous service lifetime predictions for EVA are discussed. The known factors that effect the discoloration rate of several EVA formulations are discussed in which the reduction in rate by using UV-absorbing superstrates is a prime example. A summary is given of what is and is not known about EVA degradation mechanisms, degradation from exposures in field-deployed modeules and/or laboratory testing, and factors that contribute to EVA stability or degradation. Finally, conclusions about using Elvax 150 in EVA formulations are summarized, and future prospects for developing the next-generation pottant for encapsulating PV modules are discussed.     

SJT-B助剂/表面活性剂/聚合物三元复合体系的黏度和界面张力研究

助剂SJT-B是10%的磷硅酸盐胶体溶液,含有Na^＋和K^＋、SiO3^2-和PO4^3-等离子,在活化状态下一部分SiO3^2-和PO4^3-生成具5个负电荷的聚磷硅酸根链状阴离子,后者可结合Ca^2＋、Mg^2＋而形成纳米磷硅酸盐胶态粒子,避免结垢并防止金属腐蚀。以助剂SJT-B代替NaOH,用大庆油田回注污水配制SJT-B/烷基苯磺酸盐/聚合物三元复合溶液,取SJT-B浓度为1.0-8.0 g/kg,石油磺酸盐浓度为0.5-4.0 g/kg,聚合物浓度为1.2 g/kg,按排列组合法得到25个实验配方。对照NaOH/石油磺酸盐/聚合物溶液组成为12/3.0/1.2 g/kg,初配黏度（45℃,7.34s^-1）27.3 mPa·s,界面张力（45℃）3.20×10^-3mN/m。初配各实验配方溶液黏度31.2-44.8 mPa·s,45℃老化30天后黏度降低率2.71%-36.97%;初始界面张力最低值1.13×10^-3mN/m,最高值4.34×10^-2mN/m,在界面活性图上,10^-3mN/m超低界面张力区出现在高SJT-B和烷基苯磺酸盐区,老化后该区扩大。筛选出的SJT-B/石油磺酸盐/聚合物体系组成为4.0/3.0/1.2 g/kg,其初始黏度为37.1 mPa·s,老化后黏度降低3.77%,初始界面张力1.79×10^-2mN/m。图2表3参8。     

环氧玻璃钢衬里在化工设备中的应用

本文叙述了非标准化工设备的环氧玻璃钢防腐衬里工艺、配方及使用考查结果．     

中原高温高盐油藏疏水缔合聚合物凝胶调剖剂研究

针对中原油田高温(>80℃)、高盐度(>50 g/L)、高硬度(>1 g/L)砂岩油藏,研制了地下成胶的高热稳定性聚合物凝胶调剖剂。所用聚合物为疏水缔合聚合物AP-P4,M=9.0×106,HD=27%,疏水基摩尔分数0.2%;交联剂为可生成酚醛树脂的3种化合物;调剖剂胶液用矿化度160 g/L的马寨油田污水配制;实验温度95℃。根据形成的凝胶黏度(95℃,1.1 s-1)确定交联剂各组分用量为:MZ-YL 0.429%,MZ-BE 0.060%,MZ-XS 0.012%;酸度调整剂用量0.12%;成胶时间10~15小时。2.5、3.0、3.5 g/L AP-P4的凝胶在95℃老化100天后黏度保持在~40 Pa.s及以上。初配制胶液在3000 r/min下剪切15分钟后黏度降低87.5%~89.0%,但成胶后和老化过程中凝胶黏度只比未剪切样降低17.1%~6.6%。3.5 g/L AP-P4的调剖剂对~1μm2的6支储层岩心的堵塞率在88.1%~95.8%范围,平均93.3%,造成的残余阻力系数在15.2~28.6范围,平均19.8,使渗透率级差2.3~8.0的4组双人造岩心的注水流量比发生不同程度的反转。认为该凝胶调剖剂高温下稳定性好的原因,是强化学交联密度低,因而凝胶脱水收缩作用弱。图2表5参5。     

Polymerization behavior and polymer properties of eosin-mediated surface modification reactions

Surface modification by surface-mediated polymerization necessitates control of the grafted polymer film thicknesses to achieve the desired property changes. Here, a microarray format is used to assess a range of reaction conditions and formulations rapidly in regards to the film thicknesses achieved and the polymerization behavior. Monomer formulations initiated by eosin conjugates with varying concentrations of poly(ethylene glycol) diacrylate (PEGDA), N-methyldiethanolamine (MDEA), and 1-vinyl-2-pyrrolidone (VP) were evaluated. Acrylamide with MDEA or ascorbic acid as a coinitiator was also investigated. The best formulation was found to be 40 wt% acrylamide with MDEA which yielded four to eightfold thicker films (maximum polymer thickness increased from 180 nm to 1420 nm) and generated visible films from fivefold lower eosin surface densities (2.8 versus 14 eosins/μm²) compared to a corresponding PEGDA formulation. Using a microarray format to assess multiple initiator surface densities enabled facile identification of a monomer formulation that yields the desired polymer properties and polymerization behavior across the requisite range of initiator surface densities.     

Motion-based method for estimating time required to attach self-adhesive insulators

A self-adhesive insulator is a component of a home appliance that is used to suppress vibration or prevent humidity affecting the internal parts of the appliance. There is a wide range of types and designs available, allowing them to be applied to areas having different shapes. At the design stage, once an insulator design has been developed sufficiently to identify its dimensions and features, the attaching time and baseline cost must be estimated with reasonable accuracy to enable a comparison of vendor quotes. However, the current estimation method is not sufficiently accurate in terms of the baseline cost. This paper presents a motion-based time-estimating scheme with which the time required for the attachment of such insulators can be calculated more accurately. The scheme has been developed by analyzing the motions needed to attach 350 insulators and then designating representative motions and their time values. For this purpose, a modular arrangement of predetermined time standards (MODAPTS) is adopted. Motion-based time-estimation method is useful in terms of simplicity and accuracy. It enables design engineers to estimate the time required for the attachment based only on a drawing of the insulator and a few MODAPTS rules. Estimates made with this method should vary from the actual value by no more than 9.5%.     

Insect sex pheromones

The half-lives (t _1/2) for evaporative loss ofn-alkyl andn-alkenyl acetates from rubber septa were determined at temperatures varying from 15 to 35 °C. The changes int _1/2 with temperature gave high correlations with the equation, Int _1/2 = H/RT+y _o where H is the heat of vaporization,R is the gas constant,T is the absolute temperature, andy _o is a constant. Half-lives changed dramatically with temperature and the degree of change with temperature increased with increasing molecular weight. For mixtures, component ratios changed with temperature, but the degree was modest. At 20 °C there was a 7.5-fold ratio oft _1/2 between members of the homologousn-alkyl orn-alkenyl acetates differing by two carbon atoms. The large change int _1/2 with temperature and with number of carbon atoms is a consequence of the thermodynamic relationships and the temperature range of pheromone usage. Therefore, a similar degree of change inf _1/2 with temperature and number of carbon atoms will apply to other formulations of the same type (those in which the rate of evaporation is first order). The values oft _1/2 at 20 °C mainly agreed very well with those reported previously at room temperature. However, our previously reported values for pentadecyl and hexadecyl acetate were revised. Half-lives were shown to depend on the vapor pressure of a compound in the formulation substrate, but not on the vapor pressure of the pure compound.Mention of a commercial or proprietary product does not constitute an endorsement by the USDA.     

A vapor collection and thermal desorption method to measure semiochemical release rates from controlled release formulations

Chemicals (bp 270–490 °C/1 atm) evaporated from a controlled-release formulation dispenser were carried by an airflow to a collector packed with a polymeric adsorbent. After a set time, the chemicals were recovered by thermally desorbing them onto a gas-liquid chromatograpic column. They were then separated and quantified. The apparatus is described, and the requirements for its successful use are discussed. The soundness of the thermal desorption technique was confirmed by comparison with another technique: solvent elution from the collector. The advantages of the former technique are discussed.Mention of a commercial or proprietary product in this paper does not constitute an endorsement of that product by the USDA.     

水基性农药制剂的开发和前景

论述了水基性农药制剂的内容和类型,详细地讨论了悬浮剂、水乳剂和微乳剂水基性制剂的开发、优劣和前景。指出微乳剂在国际上不是剂型开发的趋势,国内开发微乳剂应审慎对待;而开发悬浮剂和水乳剂的水基性制剂是更有利和有前景的。