Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Effect of PyC interface phase on the cyclic ablation resistance and flexural properties of two-dimensional Cf/HfC composites

Composites based on hafnium carbide and reinforced with continuous naked carbon fiber with and without PyC interface were prepared at low temperature by precursor infiltration and pyrolysis and chemical vapor deposition method. The microstructure, mechanical property, cyclic ablation and fiber bundle push-in tests of the composites were investigated. The results show that after three times ablation cycles, the bending strength of samples without PyC interface decreased by 63.6 %; the bending strength of samples with PyC interface only decreased by 37.8 %. The force displacement curve of the samples with PyC interface presented a well pseudoplastic deformation state. The mechanical behavior difference of two kinds of composites was due to crucial function of PyC interface phase including protection of fiber and weakening of fiber/matrix interface.     

A methodology for the estimation of transverse failure strength of an oxidized lamina from isothermal aging studies

Surface oxidation and ensuing damage substantially decrease the service life of High Temperature Polymer Matrix Composite (HTPMC) structures. Oxidative degradation behavior of composites is strongly dependent on the coupling between chemical and mechanical responses of the material. In a composite lamina, the onset of damage and subsequent coupled acceleration of both damage and oxidation are controlled by the transverse failure strength of the oxidized regions. The direct measurement of this strength from experimentation is challenging and cumbersome. A model-based methodology for estimating the mean transverse failure strength of the oxidized regions of a unidirectional composite is described in this paper. As the strength of the oxidized region is expected to show a high-degree of spatial variability, the estimated mean is shown to be relatively insensitive to the effect of strength variance. The developed methodology is illustrated with isothermal aging data available for a typical high-temperature composite system.     

Electromagnetic shielding properties of iron oxide impregnated kenaf bast fiberboard

The electromagnetic shielding effectiveness of kenaf fiber based composites with different iron oxide impregnation levels was investigated. The kenaf fibers were retted for removing the lignin and extractives from the fibers and magnetized. Using the unsaturated polyester and the magnetized fibers, kenaf fiber based composites were manufactured by the compression molding process. The transmission energies of the composites were characterized when the composite samples were exposed under the irradiation of electromagnetic (EM) wave with a variable frequency from 9 GHz to 11 GHz. Using the Scanning Electron Microscope (SEM), the iron oxide nanoparticles were observed on the surfaces and inside the micropore structures of single fibers. As the Fe content increased from 0% to 6.8%, 15.9% and 18.0%, the total surface free energy of kenaf fibers with the magnetizing treatments increased from 44.8 mJ/m² to 46.1 mJ/m², 48.8 mJ/m² and 53.0 mJ/m², respectively, while the modulus of elasticity reduced from 2875 MPa to 2729 MPa, 2487 MPa and 2007 MPa, respectively. Meanwhile, the shielding effectiveness was increased from 30–50% to 60–70%, 65–75% and 70–80%, respectively.     

Finite element analysis of fracture behavior in ceramics: Competition between artificial notch and internal defects under three-point bending

Evaluation of the nonlinear relationship between the surface defect size and fracture strength of ceramics is important for engineering applications. In this study, we aim to predict the apparent nonlinear relationship between the defect size and fracture strength of single-edge notched beams (SENBs) using the finite element method. Specifically, we applied the methodology for predicting fracture strength from microstructure distribution data (relative density, pore size, aspect ratio, and grain size) to a finite element analysis (FEA) model in which the shape and size of the initial defects are defined at notch locations. By reproducing the apparent nonlinearity caused by the competition between the surface and internal defects within the framework of linear elastic fracture mechanics, the effectiveness of the FEA methodology for the evaluation of strength scatter and allowable crack size in ceramics was demonstrated.     

Flexural behaviour of RC slabs strengthened with prestressed CFRP strips using different anchorage systems

The Externally Bonded Reinforcement (EBR) technique using Carbon Fiber-Reinforced Polymers (CFRP) has been commonly used to strengthen concrete structures in flexure. The use of prestressed CFRP material offers several advantages well-reported in the literature. Regardless of such as benefits, several studies on different topics are missing. The present work intends to contribute to the knowledge of two commercially available systems that differ on the type of anchorage: (i) the Mechanical Anchorage (MA), and (ii) the Gradient Anchorage (GA). For that purpose, an experimental program was carried out with twelve slabs monotonically tested under displacement control up to failure by using a four-point bending test configuration. The effect of type of anchorage system (MA and GA), prestrain level (0 and 0.4%), width (50 mm and 80 mm) and thickness (1.2 mm and 1.4 mm) of the CFRP laminate, and the surface preparation (grinded and sandblasted) on the flexural response were the main studied parameters. Better performance was observed for the slabs: (i) with prestressed laminates, (ii) for the MA system, and (iii) with sandblasted surface preparation.     

Microwave and conventional treatment of low-cement high-alumina castables with different water-to-cement ratio; Part II. Dehydration

Modern refractory castables contain between 3.5 and 5?wt.-% water that is necessary for sufficient flow during emplacement and for the formation of hydrate phases, necessary for the green strength of the material. Prior to the high temperature use of this material, it must be dried very carefully to avoid explosive spalling.This paper will demonstrate that beside conventional drying of pre-shaped materials in resistance furnaces microwave radiation is an energy saving and rapid method to remove pore water as well as hydrate bond water from the castable. In comparison to resistance furnaces, the use of microwave radiation does not affect the castable properties as there are mechanical strength (MOR, CCS), open porosity and pore size distribution. This study proved microwave radiation as valuable alternative with a series of tabular alumina based low cement castables (LLC) in which the water-to-cement-ratio (wcr = 0.64, 0.75, 0.82 and 1.13) was systematically altered by changing the cement concentration at constant mixing water concentration of 4.5%.     

Assessment of the effectiveness of steel fibre reinforcement for the punching resistance of flat slabs by experimental research and design approach

The present paper deals with the experimental assessment of the effectiveness of steel fibre reinforcement in terms of punching resistance of centrically loaded flat slabs, and to the development of an analytical model capable of predicting the punching behaviour of this type of structures. For this purpose, eight slabs of 2550 × 2550 × 150 mm³ dimensions were tested up to failure, by investigating the influence of the content of steel fibres (0, 60, 75 and 90 kg/m³) and concrete strength class (50 and 70 MPa). Two reference slabs without fibre reinforcement, one for each concrete strength class, and one slab for each fibre content and each strength class compose the experimental program. All slabs were flexurally reinforced with a grid of ribbed steel bars in a percentage to assure punching failure mode for the reference slabs. Hooked ends steel fibres provided the unique shear reinforcement. The results have revealed that steel fibres are very effective in converting brittle punching failure into ductile flexural failure, by increasing both the ultimate load and deflection, as long as adequate fibre reinforcement is assured. An analytical model was developed based on the most recent concepts proposed by the fib Mode Code 2010 for predicting the punching resistance of flat slabs and for the characterization of the behaviour of fibre reinforced concrete. The most refined version of this model was capable of predicting the punching resistance of the tested slabs with excellent accuracy and coefficient of variation of about 5%.     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

陶瓷减水剂、助磨剂、增强剂的发展现状、趋势及展望

阐述了陶瓷行业所用添加剂的分类，以及目前国际上主要生产陶瓷添加剂的厂家及主要产品，详细介绍了陶瓷坯体减水剂、助磨剂、增强剂的种类、应用、性能特点和它们与陶瓷材料的作用机理，并对陶瓷添加剂的发展前景进行了展望。