Generation,validation and application of dynamic load profiles in flow measurement using cavitating Herschel–Venturi nozzles

Today, utility meters for water are tested for measurement behavior at stable operating conditions at specified flow rates as part of the approval process. The measurement error that occurs during start and stop or when changing between flow rates may not be taken into account. In addition, there are new technologies whose measuring behavior under real-world conditions is only known to a limited extend. To take these facts into account, a new method has been developed and tested to determine the measurement behavior of water meters under dynamic load profiles as they occur in the real application. For this purpose, a test rig for flow rate measurement was extended by a cavitation nozzle apparatus and the generation of dynamic load profiles was validated. For the cavitation nozzles used, possible factors influencing the flow rate, such as temperature and purity of the water as well as the upstream pressure were investigated. Using different types of domestic water meters, the applicability of the dynamic test procedure was demonstrated and the measurement behavior of the meters was characterised.     

上水口环形吹氩对中间包内渣眼形成的影响

 中间包上水口环形吹氩可以在塞棒周围形成清洗钢液的环形气幕，同时部分氩气泡随钢液进入上水口内，可以减少非金属夹杂物在水口内壁的黏附，起到防止水口堵塞的作用。然而，不合理的吹氩量会导致中间包内液面渣层受过强的气液羽流冲击而形成渣眼，使得钢液裸露并发生二次氧化，严重影响铸坯质量。采用标准 k ε 湍流模型研究中间包内流体流动，采用DPM模型和VOF模型耦合方法，研究上水口环形吹氩条件下渣眼的形成及演化规律。结果表明，上水口环形吹氩在塞棒周围形成较强的上升流，塞棒上部邻近区域存在多个涡流区；在钢液涡流的影响下，中间包液渣下层远离塞棒区域，上层向塞棒区域迁移；随着吹氩量的增大，平均湍动能增大，塞棒附近钢液速度逐渐增大，钢渣界面钢液速度先增大后减小，渣眼边缘钢液速度先增大后减小然后再增大，速度与垂直方向夹角逐渐减小；增大吹氩量，中间包熔池液面形成以塞棒为中心的渣眼，渣眼面积逐渐增大。试验条件下不产生渣眼的临界吹氩量为4.2 L/min，对应的钢渣界面最大速度为0.247 m/s，与垂直方向夹角为70°。     

铝碳质长水口用低铝抗氧化涂层的研制

为抑制铝碳质长水口使用过程中石墨的氧化，其表面会涂覆含 20%~30%Al₂O₃的抗氧化涂层，但切割丝钢等特种钢冶炼过程必须严格控制钢液中夹杂的 Al₂O₃的含量，因此需要制备低氧化铝含量的抗氧化涂层。本文通过调节涂料组成、加水量和水玻璃加入量制备了低铝抗氧化涂层，并利用扫描电镜分析了抗氧化实验后试样断口的显微结构。结果表明：以粘土粉、钾长石粉和硅砂为主要原料，添加 10%硼砂的涂料可在 800 ℃形成良好的釉层，此时涂料中 A12O3的含量可降至 12%，得到了低铝涂料；当加入占涂料质量 80%的水和 40%的水玻璃时，涂层具有最佳的涂覆性能和抗氧化性能，涂层和长水口基体结合致密，保护了长水口中的石墨不被氧化。     

FCC装置主风分布管喷嘴磨损的气相流场分析

用FLUENT流体计算软件对FCC装置再生器树枝状分布管喷嘴流场进行了计算,分析了喷嘴发生磨损的机理.对喷嘴流场的计算表明喷嘴磨损是催化剂颗粒造成的,属于气固两相流冲蚀磨损.由于某些喷嘴的压力降偏低和流场存在偏流,造成催化剂颗粒倒流至喷嘴内部或分布支管内部.催化剂颗粒流经喷嘴时,斜向冲击内壁产生冲蚀磨损.磨损首先发生在喷嘴内壁局部区域,形成圆弧状磨损痕迹,再将喷嘴磨穿,逐渐扩大为整个喷嘴,磨掉喷嘴.这些分析结果可为主风分布管的设计提供帮助.     

一种洁净的、非接触性的新型粘合剂喷洒技术

介绍了Robatech公司开发的PFC喷嘴。这种喷嘴为标准化组件，具有较大的适用性，既适用于新厂配套，也适用于老设备改造。     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

Extension of a combined analytical/numerical initial value problem solver for turbulent mixing with combustion

Here, we describe the development of a reacting flow multi-species/combustion methodology, implemented as an extension to the differential reduced ejector analysis (DREA) computer program [Mathematical and computer modeling, vol. 31, 2000, p. 21; Appl. Math. Model. 25 (2001) 427; Comput. Math. Appl. 43(10–11); NASA Contractor Report, 1998]. Use of the single fluid IVP solver framework that was developed for the original DREA model has been directly coupled into the combustion formulation. With these modifications, the analysis has an elementary single step reaction Fuel+Oxidizer→Product combustion capability. Though approximate in nature, the simplicity and efficiency of the DREA formulation make it suitable for its original niche, namely design and preliminary design environments where more complex and expensive models may be inappropriate.     

磨料高压水除鳞系统设计研究

磨料高压水除鳞系统取代酸洗线，原机械部分和磨料高压水部分都作了较大改进，才能保证除鳞彻底。     

自振空化射流提高钻井速度的实验研究

空化射流用于提高钻井速度的可行性研究结果表明，在钻进作业中，利用空泡破裂产生强大破坏作用来提高钻探的效率，其效果显著，可行性高。室内实验表明，自振空化射流在比普通喷嘴射流更深的井底或更高的围压条件下，有更大的起始空化数和更强的空化能力。自振空化喷嘴起始空化数大都在1.0以上，最高达到1.67，而锥形喷嘴最高仅为0.43，围压下其冲蚀效率是锥形喷嘴的1~2倍。现场试验同样证实设计的自振空化射流喷嘴在保护钻头、减少钻头磨损及增加进尺、提高机械钻速方面有显著作用。