Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.     

Effect of microstructure on the fatigue crack growth behaviour of a near-α Ti alloy

Fatigue crack growth behaviour of Ti–6Al–2Zr–1.5Mo–1.5V (VT-20 a near-α Ti alloy) was studied in lamellar, bimodal and acicular microstructural conditions. Fatigue crack growth tests at both increasing and decreasing stress intensity factor range values were performed at ambient temperature and a loading ratio of 0.3 using compact tension samples. Lamellar and acicular microstructures showed lower fatigue crack growth rates as compared to the bimodal microstructure due to the tortuous nature of cracks in the former and the cleavage of primary α in the latter. The threshold stress intensity factor range was highest for acicular microstructure.     

Fatigue performance of Friction Stir Welded titanium structural joints

The Friction Stir Welding process for producing corner and T-joints out of 6 mm Ti–6Al–4V was developed in this effort using previous work on butt weld joints as a starting point. A limited number of corner joints were also subjected to a bending fatigue test to preliminarily assess the applicability of the process in producing fatigue critical structures. These results were also compared to predictions made by applying stress concentration factors to previously generated uniaxial butt joint test data. While additional testing is still required to obtain a higher degree of confidence in the conclusions of this study, it was found that the performance of these corner joints in fatigue could be compared to butt joint data when a geometrically based stress concentration factor is applied. Furthermore, these welded joints possessed equivalent fatigue performance relative to identical test specimens machined from wrought product forms, both bar and extrusion. Thus, from the perspective of fatigue design, this study has shown that Friction Stir Welding is able to produce structures with the same performance as currently made from wrought materials.     

乙烯齐聚催化剂研究进展

乙烯齐聚是合成直链低碳α-烯烃最先进的方法，直链低碳α-烯烃可用于生产低密度聚乙烯和高密度聚乙烯等多种精细化学品。本文综述了乙烯齐聚催化体系的研究进展，重点介绍了镍、锆、钛催化剂的组成以及反应时间、反应温度、溶剂、助催化剂等因素对乙烯齐聚活性和选择性的影响，并讨论了典型镍的催化机理。     

Ionic transport in amorphous anodic titania stabilised by incorporation of silicon species

Incorporation of silicon species from an alloy substrate into anodic titania is shown to stabilise the structure of the film, facilitating investigation of the ionic transport processes in amorphous titania grown at high efficiency. Thus, an amorphous anodic film developed on a sputtering-deposited Ti-6 at.%Si alloy formed to 100 V in phosphoric acid electrolyte in contrast to a partially crystalline film developed on relatively pure titanium at <20 V. Silicon species, which are immobile and act as marker species in the growing film, are present in the inner 58% of the film thickness. Evidently, the film material forms simultaneously at the film/electrolyte and alloy/film interfaces by co-operative transport of cations and anions, as is usual in amorphous anodic oxides. The phosphate anions incorporated from the electrolyte migrate inward at 0.34 times the rate of O²⁻ ions and hence are present in the outer 62% of the film thickness.     

武山铜矿主井系统延深改造及效果浅析

武山铜矿主井延深时根据新的采、选工艺要求，在前期工程的基础上，对其箕斗提升系统进行改造，增设坑内破碎。针对该矿特粘的矿石性质和前期工程遗留问题，在具体设计和实施过程中采取特别措施保证系统通畅和安全并注意节省投资。同时对尚存在的问题也提出了新的思考。     

β21s高强度钛合金的铣削试验研究

针对一种新型的难加工钛合金材料β21s,进行了刀具磨损试验和铣削力的测量试验,对材料的切削加工性进行评价,并且给出优选结果,为实际生产提供参考。     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

Formation and electronic structure of interface

In the present work the formation of the interface between polycrystalline silver and thin films of titanium oxide was studied with photoelectron spectroscopy (XPS, UPS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS). Titanium oxide was deposited stepwise on 100 nm thick silver films by reactive magnetron sputtering allowing to study the evolution of the interface formation process. The process involves two steps: formation of thin layer of silver oxide and subsequent growth of the TiO₂ film. For better understanding of the silver oxidation process, pure silver films were exposed to a low temperature Ar/O plasma for different time intervals providing a possibility to investigate early stages of the oxide film growth.     

Photochemical reduction of molecular weight and number of double bonds in natural rubber film

Natural rubber (NR) can be degraded depending on various factors such as heat, mechanical force, chemical reaction, and light. Light is a very interesting factor because it can cause the NR to degrade under low temperature and pressure. The photo-degradation of NR films was carried out to investigate the effects of the light and the temperature on the reduction of the weight-average molecular weight (Mw) and the double bonds in the NR films. The NR films, with and without catalysts, titanium dioxide (TiO₂), and potassium persulfate (K₂S₂O₈), were exposed to light from a mercury light bulb at 7,000 and 36,000 lux, and at the temperature of 25 °C and 80 °C for 192 hrs. After exposure, the Mw of the NR films was analyzed by gel permeation chromatography (GPC). Changes in the Mw were used to construct a kinetic model for the process, (1/Mw)=(1/Mw₀)+(kt/2M₀) where k is the rate constant, and M₀ is the Mw of the monomer unit. The linear relationship between 1/Mw and time suggested pseudo first-order processes with random scission. The Mw distribution information from the GPC was used to calculate the number of double bonds in the NR films. The trend of the double bonds reduction curves was quite similar to the result obtained from the calculation from the FTIR spectra. This indicated that this calculation method might possibly be another alternative way to obtain the number of double bonds in the NR.