PLC与SEW多轴伺服驱动总线集成在玻璃生产线控中的应用

本文介绍了一种将西门子PLC与SEW多轴伺服驱动通过PROFINET总线组合集成的一套玻璃生产线线控系统的应用方案。     

A simple model for deep dynamic stall conditions

The present study is focused on modeling of dynamic stall behavior of a pitching airfoil. The deep stall regime is in particular considered. A model is proposed, which has a low implementation and computational complexity but yet is able to deal with different types of dynamic stall conditions, including those characterized by multiple vortex shedding at the airfoil leading edge. The proposed model is appraised against an extensive data set of experimental (α,C_L) curves for NACA0012. The results of an existing widely used model, having comparable complexity, are also shown for comparison. The proposed model is able to well reproduce not only the classic curves of deep dynamic stall but also the curves characterized by lift oscillations at high angles of attack due to the shedding of multiple vortices. Furthermore, the model appears to be robust to variations of its parameters from the optimal values and of the airfoil geometry. Finally, the model is successfully implemented in a commercial CFD software and applied to the simulation of a vertical axis wind turbine within the actuator cylinder approach. The accuracy of the prediction of the turbine power coefficient in the whole rotation cycle is very good for the optimal working condition of the turbine, for which the model parameters were calibrated. Fairly good accuracy is also obtained in significantly different working conditions without any further calibration.     

X射线三轴晶衍射法测量半绝缘GaAs单晶的化学配比

采用X射线三轴晶衍射法,根据As间隙原子对作为过量As在GaAs单晶材料中存在的主要形式的模型,可以无损、高精度测量半绝缘GaAs单晶的化学配比.并探讨了引起晶格变化的原因及其与熔体组分的关系,对于制备高质量GaAs单晶及其光电器件具有重要的意义.     

定量确定纤维织构轴密度分布的矢量法

本文将大幅度减少衍射极图测试数目的织构分析矢量法应用于定量确定纤维织构材料的晶粒取向分布;采用蒙特卡罗方法计算系数矩阵σ_(pn)(hkl)。对立方晶系的研究结果表明,由一张极图甚至一张不完整极图即可准确地构建纤维轴密度分布图。     

钢带试样位向及拉伸性能的探讨

从碳素结构钢热轧钢带各向异性的事实出发 ,阐述不同试样位向导致同一钢带不同的拉伸性能 ,因而影响钢带合格与否的判定。在全面考虑钢带和焊管标准的基础上 ,提出解决钢带判定的两种方法。同时 ,还对标准中存在的缺点作了说明 ,提出改进意见 ,供标准修订时参考。     

25mm厚钢板产生层间撕裂的原因和防治

层间撕裂并非是厚板独有的质量问题 ,结合工程实例 ,分析 2 5mm厚低合金钢板产生层间撕裂的原因。通过对钢材的超声波探伤检测、化学成分分析和Z向性能检测 ,指出层间撕裂主要与节点设计不当和钢材内非金属夹杂物偏析、分层有关 ,并提出了预防措施。对产生裂纹的构件视严重情况提出了不同的修补处理方法     

Early impact of a fat-enriched diet on behavioral responses of male and female rats.

Prolonged high-fat diets have been shown to affect an organism's stress responsiveness at the neuroendocrine level. In the present study, the authors used a 7-day protocol of fat administration in adult rats of both sexes to investigate the early behavioral impact of a moderately fat (20%) diet, often used by Western societies, on rats' reaction to acute stress and novelty. Their results show that this diet can reduce the rats' active behavioral responses to subsequent stressors and influence their corticosterone secretion. Fat-fed male rats adopted a less active behavior to cope with forced swimming stress, whereas their exploratory behavior in the open field environment was rather increased compared with chow-fed males. Fat-fed female rats exhibited a less active behavioral response to both stress paradigms compared with their chow-fed counterparts. Fat diet abolished facilitation in corticosterone secretion following a subsequent stressor in both sexes. However, only in males did fat diet exaggerate corticosterone response to novelty, irrespective of the previous stress history of the rat. These data indicate that a short-term metabolic stress can modify the rats' stress coping strategy in interaction with the gender. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

四维空间直线绕平面的旋转

本文对四维空间直线绕平面旋转的轨迹进行一投详尽的讨论，按照直线与“轴平面”的相对位置不同，该旋转轨迹分别为圆柱面、圆锥面和单叶回转双曲面，并认为这些回转曲面的轴线是过该直线的与“轴平面”垂直的超平面与“轴平面”的交线。     

铣槽专用夹具设计

从零件的几何形状 ,配合要求入手 ,设计零件铣槽的专用夹具     

带有集中质量的分布质量弹性转动横振精确解

求得了带有集中质量的分布质量弹性转轴系统横向自由振动的频率方程和振型函数的精确解析表达式，及其与不转动轴系统自由振动的频率方程和振型函数及转动角速度之间的精确解析关系