Optimization of hydrogen enrichment via palladium membrane in vacuum environments using Taguchi method and normalized regression analysis

In this study, the separation of hydrogen from gas mixtures using a palladium membrane coupled with a vacuum environment on the permeate side was studied experimentally. The gas mixtures composed of H₂, N₂, and CO₂ were used as the feed. Hydrogen permeation fluxes were measured with membrane operating temperature in the range of 320–380 °C, pressures on the retentate side in the range of 2–5 atm, and vacuum pressures on the permeate side in the range of 15–51 kPa. The Taguchi method was used to design the operating conditions for the experiments based on an orthogonal array. Using the measured H₂ permeation fluxes from the Taguchi approach, the stepwise regression analysis was also employed for establishing the prediction models of H₂ permeation flux, followed by the analysis of variance (ANOVA) to identify the significance and suitability of operating conditions. Based on both the Taguchi approach and ANOVA, the H₂ permeation flux was mostly affected by the gas mixture composition, followed by the retentate side pressure, the vacuum degree, and the membrane temperature. The predicted optimal operating conditions were the gas mixture with 75% H₂ and 25% N₂, the membrane temperature of 320 °C, the retentate side pressure of 5 atm, and the vacuum degree of 51 kPa. Under these conditions, the H₂ permeation flux was 0.185 mol s^?1 m^?2. A second-order normalized regression model with a relative error of less than 7% was obtained based on the measured H₂ permeation flux.     

Systematic optimization of corrosion,bioactivity, and biocompatibility behaviors of calcium-phosphate plasma electrolytic oxidation (PEO) coatings on titanium substrates

To optimize the corrosion, bioactivity, and biocompatibility behaviors of plasma electrolytic oxidation (PEO) coatings on titanium substrates, the effects of five process variables including frequency, current density, duty cycle, treatment time, and electrolyte Ca/P ratio were evaluated. In our systematic study, a Taguchi design of experimental based on an L16 orthogonal array was used. For this, the coatings characteristics such as the surface roughness, wettability, rutile to anatase and Ca/P ratios, and corrosion polarization resistance were investigated. After determining the optimum process variables for each response, the apatite forming ability in SBF (bioactivity behavior) and MG63 cell attachment and flattening (biocompatibility behavior) for two groups of coatings were examined. The first group was optimized based on the maximum corrosion polarization resistance and the variables were set as the frequency of 2000 Hz, the current density of 5 A/dm², the duty cycle of 30%, the treatment time of 5 min, and the Ca/P ratio of 0.65 at. % in the electrolyte. For the second group, the maximum surface roughness, greatest Ca/P ratio, and highest wettability as well as the minimum rutile to anatase ratio in coatings, could be obtained when the variables were set as the frequency of 10 Hz, the current density of 12.5 A/dm², the duty cycle of 50%, the treatment time of 12.5 min, and the Ca/P ratio of 1.70 at. % in the electrolyte. The results showed that while both groups of coatings indicated a significant apatite forming ability and can serve as bioactive coatings, a proper attachment and flattening of cells and consequently, the favorable biocompatibility properties were seen only in the first group.     

Ga-doped IZO films obtained by magnetron sputtering as transparent conductors for visible and solar applications

C-axis textured thin films of gallium-doped indium zinc oxide (GIZO) with a 2% ratio of Ga/Zn, were obtained via RF-magnetron sputtering with high transparency and electrical conductivity. A Box-Behnken response surface design was used to evaluate the effects of the deposition parameters (In₂O₃ target power, deposition time, and substrate temperature) on the chemical composition, optical, electrical, and structural properties of the GIZO films. The optical constants and the electrical properties were obtained using optical models. The GIZO stoichiometry, and therefore the In/Zn atomic ratio, affected the crystallinity, crystalline parameters, band gap, and charge carrier mobility of the GIZO films. The charge carrier density was related to the change in the crystalline parameters of the hexagonal structure and the In/Zn atomic ratio. The best electrical conductivity values (1.75?×?10³ Ω^?1 cm^?1) were obtained for GIZO films with In/Zn ratio ≥?1. Several figures of merit (FOM) defined for the visible and solar regions were comparatively used to select the optimal In/Zn atomic ratio that provided the best balance between the conductivity and the transparency. The optimal In/Zn ratio was in a range of 0.85–0.90 for the GIZO films.     

Design guidelines for titania-silica-alumina ceramics with tuned anatase to rutile transformation

Titania-based ceramics with adjustable anatase-rutile fractions were obtained by milling of anatase, quartz and corundum precursors, uniaxial pressing and firing at 1100?°C. The influence of silica and alumina, combined with milling time and compaction pressure, was studied by design of experiments. The L9 orthogonal array with a three-level noise factor was employed. Firing of pure titania at 1100?°C yielded complete anatase to rutile transformation (ART), whereas stabilized samples show that an optimum amount of 9% silica and 33% alumina reduces phase transformation to only about 5?wt% rutile. An extended correlation matrix combined with analysis of variance (ANOVA) was applied to assess the combined effects of quartz, alumina, milling time and uniaxial compressing pressure on relative density, and anatase to rutile transformation. Results show absence of ART after milling, and controlled partial conversion of anatase to rutile after firing. Very good fitting was obtained by multivariate analysis on considering first and second order terms for dependence on silica contents and interactions between silica and each of the remaining factors, including milling time. This empirical dependence could be interpreted on a sound physicochemical basis, allowing the prediction of suitable compositions and processing conditions to obtain rutile-free samples by conventional ceramic processing, and to design ceramic samples with controlled fractions of anatase and rutile.     

如何加强军用软件的质量管理

军用软件在武器装备系统中的地位已经越来越重要,但我国军用软件的质量管理起步较晚,因此很有必要研究如何加强军用软件的质量管理.本文在阐述软件生命周期的基础上,从开展军用软件研制单位的软件能力评价、加强软件配置管理和加强第三方独立测试三个方面探讨了如何加强军用软件的质量管理.     

Al,Ga取代Bi：DyIG薄膜的磁和磁光特性的研究

本文报道用热分解法在玻璃衬底上制备了Ａｌ和Ｇａ取代的Ｂｉ：ＤＹＩＧ薄膜，对其磁和磁光特性做了详细研究．Ａｌ和Ｇａ取代的薄膜均可获得好的矩形比和高的矫顽力．对于Ｂｉ１．２Ｄｙ１．８Ｆｅ５－ｘＭＸＯ１２（Ｍ＝Ａ１，ＧＺ）薄膜，Ａ１和Ｇ２的最佳替代成份分别为１．０和Ｇ．７；最佳晶化温度分别为７００ｏ℃和６７５℃．在波长５１０ｎｍ附近，法拉第旋转角可达８°／ｕｍ左右．光学吸收和品质因子的研究结果表明，Ａｌ和Ｇａ取代能够影响光学吸收和品质因子，其中Ｇａ取代对光学吸收和品质因子的影响较大．     

Self-co-operative ternary pulse-compression sequences

An algorithm called a Hamming scan was developed recently for obtaining sequences with large merit factors and is adopted here to obtain such sequences within which there are nontrivial segments of large merit factors. Correlative detection of the return signal can be based simultaneously on the entire sequence and its segments with large merit factors. Such a coincidence detection scheme can be characterized by a Schur merit factor of the sequence. Sequences with large Schur merit factors are listed.     

A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

三角高程测量的不同方法比较分析

在工程施工中,经常涉及到高程测量.传统的测量方法为水准测量和三角高程测量,它们都存在着不同的优缺点.为了寻找一种能够快速测量高程,并且精度较高的方法,比较分析两种不同三角高程测量是否可行.