An accurate block-trimming device for ultramicrotomy of selected cells

A small instrument is described which is operated on the stage of a light microscope to trim resin-embedded specimens to precise levels for subsequent ultramicrotomy and to cut thin pilot sections for light microscopy. The operating procedure and examples of results are given.     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

Measurement of specimen charging in scanning electron microscopy with a kelvin probe

A vibrating Kelvin probe in form of a platinum wire loop is used to measure the surface potential U_s on electron-irradiated free-floating metal and insulator specimens as a function of electron energy E. This allows an accurate measurement of the critical electron energy E₂ for no charging. At energies below E₂, the positive charging increases with decreasing energy to U_s=2–5 eV at E=0.5 keV and switching off the collector bias of the Everhart-Thornley detector. A two-to threefold increase of U_s is observed when the bias is switched on. For E > E₂, the strong increase of a negative surface potential can be measured. Insulating films free-supported on a conductive substrate show a steep decrease to small positive and negative U_s when the film thickness becomes lower than the electron range at a critical energy E₃ > E₂. At insulating specimen the temporal decrease of charging can be measured when the electron beam is switched off.     

用小尺寸R－CT试样研究核压力容器钢断裂韧性及与Charpy试样的比较

提出了一种用双边带深侧槽的小尺寸圆形紧凑拉伸试样评定核压力容器（ＲＰＶ）钢断裂韧性的单试作试验方法，给出了用该方法测定的两个厂家生产的核压力容器用Ａ５０８ＣＬ３钢的断裂韧性参数，还与Ｃｈａｒｐｙ试样的试验结果及大尺寸标准试样的试验结果进行了比较。研究结果表明：用双边带深侧槽的小尺寸Ｒ－ＣＴ试样测得的断裂韧性值比相同恻槽深度预制疲劳裂纹Ｃｈａｒｐｙ试样的测试值更接近有效断裂韧性值，所以，用于核压力容器断裂韧性的监测是可行的。     

13SiMnNiCrMoV钢切口疲劳裂纹萌生门槛值

本文研究在13SiMnNiCrMoV 结构钢中用尖裂纹的应力强度因子来反映三点弯曲缺口试样的疲劳裂纹萌生规律。当 R=0.1,f=100Hz,试样尺寸 B×W×L=12.5×25×117mm 时,缺口名义应力幅的门槛值为Δσ_(th)=3315ρ~(0.352) MPa,0.5mm≤ρ≤5mmΔK_(th)=250ρ~(0.352) MPam~(1/2)门槛值与ρ有关。同时得到缺口裂纹萌生的循环次数 N_i 与名义应力幅Δσ、缺口曲率半径ρ的定量关系是N_i=3.98×10~(22)ρ~(1.62)/Δσ~(4.85),N_i≤10~(5.5)并讨论了(ΔK_1/ρ~(1/2))_(th)与ρ无关的结论。     

单刻线样板检定装置测量不确定度分析

分析了单刻线样板检定装置的测量不确定度，并分析了用该检定装置检定的单刻线样板的不确定度。     

鱼类耳石扫描电镜样品制备与观察

本文介绍了一种鱼类耳石样品的扫描电镜制样方法，通过对草鱼耳石进行包埋，抛磨，并用合适的腐蚀剂处理，用ＳＥＭ成功地观察了耳石的日轮及超微结构，该方法简便易行，保证所观察耳石样品的微观结构完整与清晰。     

Procedure for the evaluation of the accumulation of defects in metallic structural materials under complex elastoplastic loading

Within framework of the continual fracture mechanics, we describe the engineering approach to the assessment of scattered microdamage accumulation kinetics in metallic materials under elastoplastic loading conditions in case of plane stressed state. Automatized experimental stand and the respective investigation technique are discussed. The stand has been developed based on modification of the UMé-10T electromechanic test machine. State-of-the-art computer technologies and microprocessing hardware are incorporated in the stand automation. We present the technique of experimental assessment of damage accumulation kinetics in metallic structural materials under complex elastoplastic loading conditions with account of two different fracture (cleavage and shear) processes, which technique is based on measuring the specific electric resistance of the specimen. __________ Translated from Problemy Prochnosti, No. 1, pp. 128–137, January–February, 2006.     

同时含有稀土元素La Ce Pr Nd的材料的电子探针定量分析方法

研制了稀土六硼化物单晶LaB_6、CeB_6、PrB_6和NdB_6电子探针分析标样。根据X-射线峰位表和实测的特征X-射线谱,考察分析了La、Ce、Pr和Nd元素谱线之间的干扰情况,发现分析谱线PrLα_1受到L_αLβ_1线严重的干扰。以混合稀土金属为试样,采用扣除谱线重叠强度的背底非对称测量等方法对L_n、Ce、Pr和Nd进行了电子探针定量分析,其结果与荧光X-射线光谱分析结果符合较好。