Influence of accelerated curing on the compressive strength of polymer-modified concrete

In recent building practice, rapid construction is one of the principal requisites. Furthermore, in designing concrete structures, compressive strength is the most significant of all parameters. While 3-d and 7-d compressive strength reflects the strengths at early phases, the ultimate strength is paramount. An effort has been made in this study to develop mathematical models for predicting compressive strength of concrete incorporating ethylene vinyl acetate (EVA) at the later phases. Kolmogorov-Smirnov (KS) goodness-of-fit test was used to examine distribution of the data. The compressive strength of EVA-modified concrete was studied by incorporating various concentrations of EVA as an admixture and by testing at ages of 28, 56, 90, 120, 210, and 365 d. An accelerated compressive strength at 3.5 hours was considered as a reference strength on the basis of which all the specified strengths were predicted by means of linear regression fit. Based on the results of KS goodness-of-fit test, it was concluded that KS test statistics value (D) in each case was lower than the critical value 0.521 for a significance level of 0.05, which demonstrated that the data was normally distributed. Based on the results of compressive strength test, it was concluded that the strength of EVA-modified specimens increased at all ages and the optimum dosage of EVA was achieved at 16% concentration. Furthermore, it was concluded that predicted compressive strength values lies within a 6% difference from the actual strength values for all the mixes, which indicates the practicability of the regression equations. This research work may help in understanding the role of EVA as a viable material in polymer-based cement composites.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

On the origin of strain hardening in glassy polymers

The influence of network density on the strain hardening behaviour of amorphous polymers is studied. The network density of polystyrene is altered by blending with poly(2,6-dimethyl-1,4-phenylene-oxide) and by cross-linking during polymerisation. The network density is derived from the rubber-plateau modulus determined by dynamic mechanical thermal analysis. Subsequently uniaxial compression tests are performed to obtain the intrinsic deformation behaviour and, in particular, the strain hardening modulus. At room temperature, the strain hardening modulus proves to be proportional to the network density, irrespective of the nature of the network, i.e. physical entanglements or chemical cross-links. With increasing temperature, the strain hardening modulus is observed to decrease. This decrease appears to be related to the influence of thermal mobility of the chains, determined by the distance to the glass-transition temperature (T−T_g).     

Deformation-Strength Relationships in Short-Term Tension of Heat-Resistant Materials

The analysis of 124 curves obtained in short-term tensile tests demonstrate that they can be described by varying strain hardening and softening characteristics. Different stress–strain curves can be produced at invariable yield strength and ultimate strength and interrelated proportional variations of the above characteristics. To determine some specific stress–strain curve, it is necessary to take account of yield strength and ultimate strength as well as strain corresponding to the latter. The relations between yield strength, ultimate strength and hardening and their practically complete absence between these parameters and softening were statistically established.     

Occupational Factors and 5-Year Weight Change Among Men in a Danish National Cohort.

This study explored whether factors related to the work environment could predict changes in body mass index (BMI) and whether the effect of psychosocial factors was dependent on baseline BMI. The sample consisted of 1,980 male employees from the Danish National Work Environment Cohort Study. Changes in BMI between 1995 and 2000 were analyzed, by multiple regression, as a function of background variables and a series of occupational variables obtained in 1995. Age, baseline BMI, job insecurity, and psychological demands predicted changes in BMI. Job insecurity and high or low psychological demands increased the likelihood of weight gain among obese employees, whereas they increased the likelihood of weight loss among employees with a low BMI. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

古陶片年龄与烧结温度测定中的计算机模拟

介绍用已知年龄和烧结温度的古陶片穆斯堡尔超精细参数与年龄和烧结温度的实验关系曲线作基础，应用计算机模拟程序，自动求出未知陶片的年龄和最高烧结温度的方法。     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。     

NK-EH500调质钢爆炸硬化的冲击动力学研究

通过试验并运用爆炸冲击动力学理论NK－EH500调质钢爆炸硬化进行了深入的研究，结果表明，金属材料存在硬化极限，调整炸药组成改变爆炸硬化可以满足不同金属材料的硬化要求，隔离式爆炸硬化有利于保护硬化工件外观的完整性，本研究对拓展爆炸硬化在实践中的应用领域具有重要的理论指导意义。     

Age and gender differences in cardiac reactivity and subjective emotion responses to emotional autobiographical memories.

This research reports age and gender differences in cardiac reactivity and subjective responses to the induction of autobiographical memories related to anger, fear, sadness, and happiness. Heart rate (HR) and subjective state were assessed at baseline and after the induction of each emotion in 113 individuals (61 men, 52 women; 66% European American, 34% African American) ranging in age from 15 to 88 years (M = 50.0; SD = 20.2). Cardiac reactivity was lower in older individuals; however, for anger and fear, these age effects were significantly more pronounced for the women than the men. There were no gender differences in subjective responses, however, suggesting that the lower cardiac reactivity found among older people is dependent on gender and the specific emotion assessed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

3Cr-3Mo二次硬化钢的回火组织和力学性能

研究了3cr—3Mo二次硬化钢淬火回火后的组织和力学性能。结果表明：随回火温度的升高，试验钢中先后析出M3c、M2c和M7C3等碳化物，在575℃回火时硬度达到峰值；400一575℃回火后试验钢的抗拉强度约为l600MPa，冲击韧性为30J／cm^2；回火温度高于600℃时，强度和硬度迅速下降，冲击韧性增加；640℃回火时，以M2C型碳化物为主，抗拉强度为1100MPa，冲击韧性增加至55J／cm^2。