Plasma-assisted CO2 reforming of methane over Ni-based catalysts: Promoting role of Ag and Sn secondary metals

Carbon dioxide (CO₂) and methane (CH₄) are the primary greenhouse gases (GHGs) that drive global climate change. CO₂ reforming of CH₄ or dry reforming of CH₄ (DRM) is used for the simultaneous conversion of CO₂ and CH₄ into syngas and higher hydrocarbons. In this study, DRM was investigated using Ag–Ni/Al₂O₃ packing and Sn–Ni/Al₂O₃ packing in a parallel plate dielectric barrier discharge (DBD) reactor. The performance of the DBD reactor was significantly enhanced when applying Ag–Ni/Al₂O₃ and Sn–Ni/Al₂O₃ due to the relatively high electrical conductivity of Ag and Sn as well as their anti-coke performances. Using Ag–Ni/Al₂O₃ consisting of 1.5 wt% Ag and 5 wt% Ni/Al₂O₃ as the catalyst in the DBD reactor, 19% CH₄ conversion, 21% CO₂ conversion, 60% H₂ selectivity, 81% CO selectivity, energy efficiency of 7.9% and 0.74% (by mole) coke formation were achieved. In addition, using Sn–Ni/Al₂O₃, consisting of 0.5 wt% Sn and 5 wt% Ni/Al₂O₃, 15% CH₄ conversion, 19% CO₂ conversion, 64% H₂ selectivity, 70% CO selectivity, energy efficiency of 6.0%, and 2.1% (by mole) coke formation were achieved. Sn enhanced the reactant conversions and energy efficiency, and resulted in a reduction in coke formation; these results are comparable to that achieved when using the noble metal Ag. The decrease in the formation of coke could be correlated to the increase in the CO selectivity of the catalyst. Good dispersion of the secondary metals on Ni was found to be an important factor for the observed increases in the catalyst surface area and catalytic activities. Furthermore, the stability of the catalytic reactions was investigated for 1800 min over the 0.5 wt% Ag-5 wt% Ni/Al₂O₃ and 0.5 wt% Sn-5 wt% Ni/Al₂O₃ catalysts. The results showed an increase in the reactant conversions with an increase in the reaction time.     

Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

铝碳质长水口用低铝抗氧化涂层的研制

为抑制铝碳质长水口使用过程中石墨的氧化，其表面会涂覆含 20%~30%Al₂O₃的抗氧化涂层，但切割丝钢等特种钢冶炼过程必须严格控制钢液中夹杂的 Al₂O₃的含量，因此需要制备低氧化铝含量的抗氧化涂层。本文通过调节涂料组成、加水量和水玻璃加入量制备了低铝抗氧化涂层，并利用扫描电镜分析了抗氧化实验后试样断口的显微结构。结果表明：以粘土粉、钾长石粉和硅砂为主要原料，添加 10%硼砂的涂料可在 800 ℃形成良好的釉层，此时涂料中 A12O3的含量可降至 12%，得到了低铝涂料；当加入占涂料质量 80%的水和 40%的水玻璃时，涂层具有最佳的涂覆性能和抗氧化性能，涂层和长水口基体结合致密，保护了长水口中的石墨不被氧化。     

模铸用高铝质流钢砖的显微结构分析

选取市场上模铸用高铝质流钢砖与用后残砖作为研究对象,通过检测不同高铝质流钢砖的理化性能,对比其使用前后的显微结构变化,进一步探讨模铸过程中高铝质流钢砖的显微结构对钢铁产品质量的影响。结果表明:由于显气孔率较大、结构比较疏松、烧结不致密等特性,高铝质流钢砖在经受钢水冲刷时,钢水容易渗透至高铝质流钢砖内部,加速其损毁;其次,高铝质流钢砖与钢水发生物理化学反应后在其表面生成低熔点物,使钢水中产生夹杂物,影响钢铁产品的质量。     

上榆泉煤矿煤泥水多参数在线检测系统应用研究

针对上榆泉煤矿煤泥水性质参数人工检测周期长、误差大、滞后性严重的问题,采用多参数传感器和PLC,开发了煤泥水多参数在线检测系统。经过8 h稳定运行,平均结果显示该厂煤泥水参数为pH值为7.71、浓度9.45%、中值直径(D50)39.56μm、流量2 440 m3/h、水质硬度428.94 mg/L,与人工检测结果相一致。应用结果表明,该检测系统能够实现煤泥水多参数在线监测和数据分析功能,使煤泥水的处理更高效。     

水泥浆失水制约下套管与井眼间隙的研究

通过对水泥浆失水规律的室内试验分析以厦对注水泥顶替过程中水泥浆失水桥堵套管与井眼间隙问题的研究，建立了顶替过程中滤失层不发生水泥浆失水而桥堵环形空间的临界失水量计算模型，提出了调配水泥浆失水性能和确定合理套管井眼间隙的具体方法，对注水泥现场施工和井身结构设计具有一定的指导意义。     

一种可替代漂珠的低密度材料

漂珠低密度水泥浆由于密度低、强度高、体系稳定而在油田低压易漏层及低压油气层长封固段固井作业中获得了广泛的应用。但近年来,由于漂珠的产量越来越少,油田低成本要求急需开发代替漂珠的新型减轻材料,以满足配制低密度水泥浆的需求。开发了BCL-10S低密度混合减轻材料,其物化性能与漂珠相当,用它作减轻剂配制的低密度水泥浆性能与用漂珠作减轻剂配制的低密度水泥浆性能相媲美,并已经在长庆油田获得了应用。     

乐滩灌区输水隧洞穿合山煤矿采空区处理设计

分析了乐滩灌区工程北干渠溯河隧洞段长约1.06 km穿合山煤矿采空区的地质情况.借鉴高速公路煤矿采空区的成功处理经验,通过科学分析,对采空区变形和区域内覆岩的稳定性做了评价,论述了输水线路穿采空区段采取全充填压力注浆法的工程处理方法.     

超临界流体萃取技术生产重交通道路沥青的研究

研究了采用超临界流体萃取技术(SFEF),以减压渣油和催化裂化油浆为原料,制备重交通道路沥青产品的可行性.结果表明:当原料中油浆掺入量为10%～30%时,可以生产出牌号为AH70,AH90,AH110的重交通道路沥青产品.工业试验表明,生产牌号为AH70,AH90的重交通道路沥青,采用此技术方案是可行的.