Seismic behavior of geosynthetic-reinforced retaining walls backfilled with cohesive soil

This study investigates the seismic performance of geosynthetic-reinforced modular block retaining walls backfilled with cohesive, fine grained clay-sand soil mixture. Shaking table tests were performed for three ½ scaled (wall height 190 cm) and ¼ scaled model walls to investigate the effects of backfill type, the influence of reinforcement length and reinforcement stiffness effects. The El Centro and Kobe earthquake records of varying amplitudes were used as base acceleration. Displacement of the front wall, accelerations at different locations, strains on the reinforcements, and the visual observations of the facing and the backfill surface were used to evaluate the seismic performance of model walls. The model walls were subjected to rigorous shaking and the walls did not exhibit any stability problems or signs of impending failure. The maximum deformations observed on the models with cohesive backfill was less than half of the deformation of the sand model. The load transfers between the geogrid and cohesive soil was comparable to that of sand and hence the needed reinforcement length was similar as well. As a result; the model walls with cohesive backfills performed within acceptable limits under seismic loading conditions when compared with granular backfilled counterparts.     

聚丙烯装置聚合区设备布置及管廊的配管设计

结合工程特点及工艺流程,阐述了300 kt/a聚丙烯装置的布置原则,管道、管架设计要点和方法,以及需要注意的问题。     

The hot compaction behaviour of woven oriented polypropylene fibres and tapes. I. Mechanical properties

The aim of this work was to establish the important parameters that control the hot compaction behaviour of woven oriented polypropylene. Five commercial woven cloths, based on four different polypropylene polymers, were selected so that the perceived important variables could be studied. These include the mechanical properties of the original oriented tapes or fibres, the geometry of the oriented reinforcement (fibres or tapes), the mechanical properties of the base polymer (which are crucially dependant on the molecular weight and morphology), and the weave style. The five cloths were chosen so as to explore the boundaries of these various parameters, i.e. low and high molecular weight: circular or rectangular reinforcement (fibres or tapes): low or high tape initial orientation: coarse or fine weave.A vital aspect of this study was the realisation that hot compacted polypropylene could be envisaged as a composite, comprising an oriented ‘reinforcement’ bound together by a matrix phase, formed by melting and recrystallisation of the original oriented material. We have established the crucial importance of the properties of the melted and recrystallised matrix phase, especially the level of ductility, in controlling the properties of the hot compacted composite.     

大型现浇钢筋混凝土U型渡槽施工技术

禹门口提水工程干渠上的十几座大型钢筋混凝土渡槽采用现浇混凝土施工方案。经过十几座渡槽的施工及通水检验，证明现浇施工技术与工艺已经成熟。本文就施工中遇到的高大排架外形与垂直度控制、槽身模板制做与固定、模具的空中支撑、运输与入仓办法等做以简单介绍。     

Nucleation of branches in elastomeric polypropylene

The formation of a crosshatched morphology during crystallization of an isotactic polypropylene with low crystallinity is studied in detail. Here, a lamella seems to grow through another nearly perpendicular lamella that was crystallized before. The crystallization was observed with in situ scanning force microscopy with a temporal resolution of 3 min per image. After crystallization the volume structure was imaged by nanotomography. A detailed scheme for the nucleation of branches is proposed.     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

定向爆破拆除框架式水塔

高 2 7m的水塔建于 193 4年 ,其顶部水罐由 12根钢筋混凝土柱支撑。在倒向侧 7根立柱上形成不同高度的爆破切口 ,背向侧倾倒中心线上的一根立柱上形成小爆破切口 ,其余 4根立柱底部打贯通孔 ,使水塔准确定向倾倒。文中讨论了立柱切口高度的计算 ,爆破参数的确定 ,并介绍了所采用的安全措施。     

80m高钢筋砼烟囱的爆破拆除

论述了控制爆破拆除钢筋砼烟囱的方案设计与力学计算、爆破参数确定、施工方法、安全防护措施、震动监测和爆破效果.     

A comparative study on the effect of VUV radiation in plasma SiOx-coated polyimide and polypropylene films

Wettability of polyimide (PI) and polypropylene (PP) films have been improved using SiO_x-like thin layers deposited from a mixture of hexamethyldisiloxane (HMDSO) and oxygen in a microwave distributed electron cyclotron resonance plasma reactor. The films wettability evolution behaviors were evaluated through the results of contact angle measurements, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The plasma depositions of SiO_x thin layers in presence of VUV radiation induce a contact angle decrease to about 7° and 35° for PI and PP films, respectively. XPS data showed that such difference in wettability is attributed to the increase of hydrophilic group's proportion at the surface of coated PI films due to VUV irradiation. AFM images showed that the PI surface topography remains relatively smooth when coated in presence of VUV radiation. However, in the case of PP films, AFM images revealed the growth of irregular structure due to a substrate etching effect supported by VUV radiation. For polymers coated without VUV irradiation, the deconvolution of the C1s peaks showed a significant decrease of CO bonds for both PI and PP substrates.     

Mycological and physical parameters for selecting suitable packaging material for pre- and post-irradiation storage of cereal grains in Ghana

Owing to the rough warehouse handling of storage sacks in tropical areas in Africa, a suitable storage sack should not support de novo growth of fungal spores because this would reduce the tensile strength of the packaging material and act as a springboard for infecting grain contents. This paper reports the effect of activity of saprophytic fungi on the tensile strength of jute and woven polypropylene sacks. New woven polypropylene sacks carried lower levels of fungal spores (1.3×10¹ cfu/72 cm²) than jute sacks (3.0×10³ cfu/72 cm²). The natural mould penetration and growth was examined on sections (4×5 cm) of both jute and woven polypropylene after previous incubation at relative humidities of 55, 60, 65, 70, 75, 80, 90 and 95% for 10 weeks by placing them on Sabouraud's Agar. There was a significant difference (P = 0.05 level of significance) between the higher penetration of mould growth on jute sacks and that obtained on woven polypropylene sacks. Saprophytic fungi (Aspergillus candidus, A. flavus, A. fumigatus, A. niger, A. japonicus, A. parasiticus, A. ustus, Fusarium oxysporium, F. moniliforme, Penicillium verucosum var. cyclopium, Rhizopus oryzae and Trichoderma viride) isolated from jute sacks reduced tensile strength, measured by an Instron Model 1026, by 50–75% after 10 weeks at 90% R.H. Same fungal species on woven polypropylene sacks did not alter the tensile strength. Woven polypropylene sacks did not absorb moisture whilst the moisture content of jute sacks increased by 5.3–6.0% in 10 weeks at 90% R.H. with concomitant increase in mould and yeast counts by 1–2 log cycles. Evidence is presented to show that there was a positive correlation between the final mycoflora on jute sacks and loss in tensile strength. No correlation, however, was found between the total aerobic bacteria on jute sacks and the concomitant reduction in tensile strength. Fungi therefore play a major role in the reduction of tensile strength of jute sacks. Sterilization by gamma irradiation (8.0 kGy) of jute and woven polypropylene sacks did not affect their intrinsic tensile strength. Woven polypropylene sacks therefore have many microbiological and physical advantages over the traditional jute sacks to merit their use for grain storage in tropical areas like Ghana.