Twin screw granulation – review of current progress

Twin screw granulation (TSG) is a new process of interest to the pharmaceutical community that can continuously wet granulate powders, doing so at lower liquid concentrations and with better product consistency than found by a high shear batch mixer. A considerable body of research has evolved over the short time since this process was introduced but generally with little comparison of results. A certain degree of confidence has been developed through these studies related to how process variables and many attributes of machinery configuration will affect granulation but some major challenges still lay ahead related to scalability, variations in the processing regimes related to degree of channel fill and the impact of wetting and granulation of complex powder formulations. This review examines the current literature for wet granulation processes studied in twin screw extrusion machinery, summarizing the influences of operational and system parameters affecting granule properties as well as strives to provide some practical observations to newly interested users of the technique.     

The effect of baking time,fillet radius,and hardness on the lifecycles of pole fastening screws in an electric motor with hydrogen embrittlement

In order to protect bolts from corrosion, electroplating such as zinc plating is widely used. However, hydrogen can easily penetrate or diffuse into the vacancies and dislocations between the lattices of bolt steel during electroplating. As the diffused hydrogen defects inside the lattice are in gaseous form, small cracks can easily be produced due to high pressure from the hydrogen gas. In this research, in order to determine the root cause of the fracture in pole fastening screws resulting from hydrogen embrittlement in typical electric motors, additional factors that accelerate hydrogen embrittlement fracture were selectively applied, including a small fillet in the head–shank transition and excessive hardness, and parametric study was performed experimentally.     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

醇镁还原法一步制取对氯苯胺的研究

醇镁还原法一步制取对氯苯胺是一种新的方法 ,研究发现最佳反应温度为 80℃～ 85℃ ,反应时间为4h ,对氯硝基苯与镁粉的用量 (物质的量比 )为 1∶3,产率为 80 %。     

编码解码芯片HD3-6408-9及其应用

编码解码芯片HD3 64 0 8 9是一种高性能的CMOS器件。这种大规模芯片主要由编码器和解码器两部分组成。在数据传输应用中 ,采用两个独立的单片机系统 ,利用编码解码芯片 (HD3 64 0 8 9)组成数字信号的接收、发送及显示部分来完成数据传输功能     

用于PET薄膜回收的螺杆设计

根据PET薄膜的特点和高分子熔融态流动理论，分析了挤出回收用螺杆的各段结构，及螺杆参数选择，设计出大长径比、深槽、双排气、高效专用螺杆。     

单层球面网壳地震反应特征分析

考虑不同矢跨比、荷载、跨度和支座刚度等多种因素的影响,对单层球面网壳在地震作用下的反应进行了较全面的研究,给出了其随各参数变化的规律,得出了在单层球面网壳抗震设计中起控制作用的是水平地震作用而不是竖向地震作用等有益的结论.此外本文还给出了由于阻尼比不同而需对引用现行抗震规范反应谱分析的网壳地震作用进行修正的建议.     

测井数据实时采集与接口设计

介绍了一种采用改进型的ＣＬＳ３７００数控测井系统对微电阻率扫描仪数据采集与控制接口的设计及实现方法。基于ＣＬＳ３７００数控测井仪和ＦＭＳ仪采用８９Ｃ５１单片机设计出通信接口，解决了微电阻率方法。基于ＣＬＳ３７００数控测井仪和ＦＭＳ仪采用８９Ｃ５１单片机设备出通信接口电路，解决了微电阻主扫描仪现现场实时处理中的瓶颈问题。     

地面驱动单螺杆泵杆柱的组合设计

根据地面驱动单螺杆泵的工作特点，分析了传递动力的抽油杯柱受力状况，认为抽油杆柱受复合载荷的作用，在承受扭矩的同时承受较大的轴向力，给出了各种载荷的计算方法。由第四强度理论，提出了把抽油杯柱设计成两级杆柱的等强度组合设计方法，即先按要求及标准确定两级杆柱的直径和长度，然后扶强度条件进行校核。根据油田的实际情况，编制了抽油杆柱电算程序，并给出了设计训一算实例。