Optimization of hydrogen enrichment via palladium membrane in vacuum environments using Taguchi method and normalized regression analysis

In this study, the separation of hydrogen from gas mixtures using a palladium membrane coupled with a vacuum environment on the permeate side was studied experimentally. The gas mixtures composed of H₂, N₂, and CO₂ were used as the feed. Hydrogen permeation fluxes were measured with membrane operating temperature in the range of 320–380 °C, pressures on the retentate side in the range of 2–5 atm, and vacuum pressures on the permeate side in the range of 15–51 kPa. The Taguchi method was used to design the operating conditions for the experiments based on an orthogonal array. Using the measured H₂ permeation fluxes from the Taguchi approach, the stepwise regression analysis was also employed for establishing the prediction models of H₂ permeation flux, followed by the analysis of variance (ANOVA) to identify the significance and suitability of operating conditions. Based on both the Taguchi approach and ANOVA, the H₂ permeation flux was mostly affected by the gas mixture composition, followed by the retentate side pressure, the vacuum degree, and the membrane temperature. The predicted optimal operating conditions were the gas mixture with 75% H₂ and 25% N₂, the membrane temperature of 320 °C, the retentate side pressure of 5 atm, and the vacuum degree of 51 kPa. Under these conditions, the H₂ permeation flux was 0.185 mol s^?1 m^?2. A second-order normalized regression model with a relative error of less than 7% was obtained based on the measured H₂ permeation flux.     

我国水-能源-粮食耦合关系及影响因素

为缓解我国水、能源和粮食资源紧张问题，促进资源可持续利用，构建水-能源-粮食系统，利用耦合协调度模型对我国的30个省（自治区、直辖市）进行测算,并利用空间杜宾模型分析主要影响因素。结果表明：2003—2017年，我国能源、粮食评价[JP]指数高于水资源评价指数，系统综合评价指数逐年递增；大部分省份耦合协调度处于初级协调水平且呈现逐年上升的态势，个别省份耦合协调度濒临失调；耦合协调度空间自相关性较强，虽有明显波动，但是呈现逐年加强的态势；影响耦合协调度的主要因素有从业人口数、固定资产投资额、人均生产总值、人口总数、[JP]文盲人口占比、工业污染排放、城镇化。     

基于粒子群优化算法的五自由度机械臂轨迹规划

为了让机械臂的工作时间达到最优,以自主研发的抛光机器人样机为研究对象,针对手表表壳表耳部分的抛光过程,提出PSO算法对五自由度机械臂轨迹规划进行优化,并通过MATLAB软件进行机械臂的仿真与分析。仿真结果表明,基于PSO算法的轨迹规划使机械臂在工作过程中加加速度不会产生突变,运动轨迹精度高,机械臂工作时间达到最优。     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Co-precipitation of nano Mg–Y/ZrO2 ternary oxide eutectic system: Effects of calcination temperature

In the family of inorganic nanomaterials, zirconia is a highly promising functional ceramic with a high refractive index, hardness, and dielectric constant, as well as excellent chemical inertness and thermal stability. These properties are enhanced in nano-zirconia ceramics, because nanopowders have a small particle size, good morphology, and uniform and dispersive distribution. In this study, a co-precipitation process was proposed to synthesise highly dispersed MgO–Y₂O₃ co-stabilized ZrO₂ nanopowders. The effects of different calcination temperatures on the crystallisation degree and particle dispersion of zirconia nanopowders were characterised by X-ray diffraction (XRD), thermogravimetry-differential scanning calorimetry (TG-DSC), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), nitrogen adsorption using the Brunauer–Emmett–Teller (BET) theory, transmission electron microscopy (TEM), and field emission scanning electron microscopy (FESEM). The optimum synthesis conditions were obtained as follows: 6 h of high-energy planetary grinding and calcination at 800 °C in an electric furnace. Under these optimum conditions, the average particle size of the prepared powder was 28.7 nm. This process enriches the literature on the controllable preparation of Mg–Y/ZrO₂ nanopowders obtained by the co-precipitation method.     

Design and synthesis of side-chain optimized poly(2,6-dimethyl-1,4-phenylene oxide)-g-poly(styrene sulfonic acid) as proton exchange membrane for fuel cell applications: Balancing the water-resistance and the sulfonation degree

Side-chain optimized poly (2,6-dimethyl-1,4-phenylene oxide)-g-poly (styrene sulfonic acid) (PPO-g-PSSA) is designed with balanced water-resistance and sulfonation degree. The PPO-g-PSSA is synthesized by controlled atom-transfer radical polymerization (ATRP) from brominated poly (2,6-dimethyl-1,4-phenylene oxide) (PPO-xBr) and ethyl styrene-4-sulfonate and followed by hydrolysis. A series of PPO-g-PSSA are prepared possessing different bromination degree (x) of PPO-xBr and polymerization degree (m) of the side-chains and the water-resistances of the fabricated membranes are investigated. The results show that a PPO-g-PSSA at relatively low x (x < 0.2) and high m (m > 4) exhibits good balance between the water-resistance and the sulfonation degree. Namely, it displays suitable proton conductivity with compromised water-resistance. Moreover, a maximum ion exchange capacity (IEC) of 3.24 mmol g^?1 is reached without the sacrifice of water-resistance. In addition, PPO-g-0.08PSSA-13 and PPO-g-0.14PSSA-4 are chosen characterized by thermogravimetric analysis, proton conductivities and mechanical properties. At 90% RH, the optimized PPO-g-0.08PPSA-13 possesses a proton conductivity of 37.9 mS cm^?1 at 40 °C and 45.5 mS cm^?1 at 95 °C, respectively.     

FE simulation of the curing behavior of the epoxy adhesive Hysol EA-9321

Cold-curing adhesives, characterized by an unsteady curing degree, present various advantages for assembling large scale structures set up under outdoor conditions. Thus various applications can be found in aerospace and automotive industries where structures are affected by thermal and mechanical loads. Hence, the curing state of the adhesive must be known to evaluate the lifetime of such bonded structures. The evolution of the polymerization of the adhesive Hysol EA-9321 during the curing process was examined in this paper. To that end, the curing degree of the adhesive was experimentally and analytically investigated for different curing cycles with a view to a potential application in the aerospace domain, where structures are assembled at low temperatures. Existing dynamic and isothermal curing models were applied to simulate the curing behavior of the adhesive. Then, an FEM model was developed to simulate the process of adhesive curing by taking into account a thermo-kinetic coupling.     

郭庄煤业选煤厂振动筛筛选形式的优化研究

针对郭庄煤业选煤厂振动筛振动筛分方式可靠性差、筛分效率低下、物料筛分率低的难题,本文提出了三种新的振动筛分方案,对不同筛分方案的实际应用效果进行了分析。结果表明三移动一摆动的振动筛分方式对物料的综合分散度最高,稳定性好,该筛分方案已在郭庄煤业选煤厂煤炭筛分过程中得到了全面的应用。     

基于灾度辨识的钢闸门巡视检查研究

巡视检查是对钢闸门要点部位开展定期、定点的信息收集,并对警兆信息做出快速辨识和评估的重要内容。应用灾度辨识的警兆信息评估方法,综合钢闸门巡视检查的各类要素信息,明确工程最大隶属的灾度等级(Ⅰ～Ⅴ级),可作为工程日常巡视检查决策的重要软技术手段。     

基于康复训练中力信号的人体参与度建模

设计一种基于人机接触力的人体主动参与程度评估模型,用于康复机器人应用中的主动康复训练。通过人体的肌电信号得到肌肉活跃度,确定肌电信号与人体参与度的关系。分析这一过程中人机接触力的变化,将腿部力信号平均值以及腰部力信号方差作为模型输入,对基于肌电信号的参与度模型进行拟合,得到基于力信号的参与度模型,使用肌电信号参与度模型对力信号参与度模型进行验证,证明了该模型的有效性。该方法避免了肌电信号采集时干扰较大且准备工作繁琐等缺点,具有良好的实用性。