Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

Influence of temperature on acoustic emission source location accuracy in underground structure

An acoustic emission (AE) experiment was carried out to explore the AE location accuracy influenced by temperature. A hollow hemispherical specimen was used to simulate common underground structures. In the process of heating with the flame, the pulse signal of constant frequency was stimulated as an AE source. Then AE signals received by each sensor were collected and used for comparing localization accuracy at different temperatures. Results show that location errors of AE keep the same phenomenon in the early and middle heating stages. In the later stage of heating, location errors of AE increase sharply due to the appearance of cracks. This provides some beneficial suggestions on decreasing location errors of structural cracks caused by temperature and improves the ability of underground structure disaster prevention and control.     

基于改进SOA-VMD的磁声发射信号去噪算法

磁声发射（MAE）是铁磁性材料磁化过程中产生的声发射信号，在构件应力检测和微观损伤检测中有着广泛的应用。针对MAE信号非稳态、复杂性、衰减性等特点，提出海鸥算法结合变分模态分解（SOA-VMD）的去噪方法，为克服海鸥算法求解过程中易陷入局部最优解问题，利用柯西变异算子产生随机迭代过程，使改进算法即柯西变异海欧算法（CVSOA）跳出早熟收敛。采用以幅值谱熵为适应度函数，优化VMD算法中分解模态个数K和二次惩戒因子α两个参数，将含噪声的MAE信号进行VMD分解重构。经仿真信号和实际检测信号分析表明，改进后的CVSOA-VMD算法全局寻优能力和去噪性能优于传统的SOA-VMD算法，降噪后的MAE信号特征值对于不同应力下均方根、偏斜度特征值的重复性更好，可靠性更高。     

Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

Acoustic emission analysis using Bayesian model selection for damage characterization in ceramic matrix composites

Acoustic emission (AE) during tensile testing of three-dimensional woven SiC/SiC composites was analyzed by a statistical modeling method based on a Bayesian approach to quantitatively evaluate the fracture process. Gaussian mixture models and Weibull mixture models were utilized as candidate models describing the AE time-series data. After fitting AE time-series data to these models with Markov Chain Monte Carlo (MCMC) methods, the model selection was conducted by stochastic complexity. Among the candidate models, the two-component Weibull mixture model was automatically selected. It was confirmed that the component distributions in the two-component Weibull mixture model were corresponding to the evolution of matrix cracking and fiber breakage, respectively. Since the proposed AE analysis method can determine the number of component distributions without the decision of researchers and inspectors, it is expected to be useful for an understanding of the fracture process in newly developed materials and the reliability assessment in service.     

基于空气质量模拟的江苏省大气污染物排放清单比较研究

大气污染物排放清单是空气质量模拟和空气污染治理的重要依据.本研究比较分析了两套覆盖江苏省的2017年大气污染物排放清单，即分别由上海市环境科学研究院、江苏省环境科学研究院编制的"长三角清单"和"江苏省清单"，并结合区域空气质量模型CMAQ评估不同清单对长三角地区2017年1、4、7、10月的空气质量模拟的影响.清单比较结果表明，除二氧化硫（SO₂）以外，江苏省清单估算的各污染物排放量较长三角清单低.通过与观测数据比较，发现两套清单对SO₂、氮氧化物（NO_x）、臭氧（O₃）和细颗粒物（PM_2.5）的模型模拟性能均较好.江苏省清单与长三角清单两者的模拟结果空间分布接近，其中江苏省清单模拟的PM_2.5和O₃在长三角多数地区略低于长三角清单的模拟结果（1月O₃除外）.江苏省清单与长三角清单均能够用于空气质量模式模拟，可为江苏地区的细颗粒物和光化学烟雾污染的控制策略制定提供参考.     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

测量二次电子空间分布特征矩阵法的有效性分析

为了准确测量不同材料在实际环境中的二次电子空间分布，设计了一种新型的二次电子发射空间分布测量结构，给出了实验测量原理，用求解特征矩阵的方法对实验结果进行处理，得到了所需的二次电子空间分布。通过模拟计算对该测量方法进行了校验，模拟结果与假设二次电子空间分布函数相吻合，表明该测量方法可靠、测量精度高，为后续样机研制奠定了理论基础。