Characterization of thick epitaxial silicon detectors from different producers after proton irradiation

Epitaxial (EPI) silicon has recently been investigated for the development of radiation tolerant detectors for future high-luminosity HEP experiments. A study of thick EPI silicon diodes irradiated with protons up to a fluence of has been performed by means of Charge Collection Efficiency (CCE) measurements, investigations with the Transient Current Technique (TCT) and standard CV/IV characterizations. The aim of the work was to investigate the impact of radiation damage as well as the influence of the wafer processing on the material performance by comparing diodes from different manufacturers. The changes of CCE, full depletion voltage and leakage current as a function of fluence are reported. While the generation of leakage current due to irradiation is similar in all investigated series of detectors, a difference in the effective doping concentration can be observed after irradiation. In the CCE measurements an anomalous drop in performance was found even for diodes exposed to very low fluences in all measured series. This result was confirmed for one series of diodes in TCT measurements with an infrared laser. TCT measurements with a red laser showed no type inversion up to fluences of for n-type devices whereas p-type diodes undergo type inversion from p- to n-type for fluences higher than .     

The AFLATOX® Project: Approaching the Development of New Generation,Natural-Based Compounds for the Containment of the Mycotoxigenic Phytopathogen Aspergillus flavus and Aflatoxin Contamination

The control of the fungal contamination on crops is considered a priority by the sanitary authorities of an increasing number of countries, and this is also due to the fact that the geographic areas interested in mycotoxin outbreaks are widening. Among the different pre- and post-harvest strategies that may be applied to prevent fungal and/or aflatoxin contamination, fungicides still play a prominent role; however, despite of countless efforts, to date the problem of food and feed contamination remains unsolved, since the essential factors that affect aflatoxins production are various and hardly to handle as a whole. In this scenario, the exploitation of bioactive natural sources to obtain new agents presenting novel mechanisms of action may represent a successful strategy to minimize, at the same time, aflatoxin contamination and the use of toxic pesticides. The Aflatox^® Project was aimed at the development of new-generation inhibitors of aflatoxigenic Aspergillus spp. proliferation and toxin production, through the modification of naturally occurring molecules: a panel of 177 compounds, belonging to the thiosemicarbazones class, have been synthesized and screened for their antifungal and anti-aflatoxigenic potential. The most effective compounds, selected as the best candidates as aflatoxin containment agents, were also evaluated in terms of cytotoxicity, genotoxicity and epi-genotoxicity to exclude potential harmful effect on the human health, the plants on which fungi grow and the whole ecosystem.     

Non-functional properties in the model-driven development of service-oriented systems

Systems based on the service-oriented architecture (SOA) principles have become an important cornerstone of the development of enterprise-scale software applications. They are characterized by separating functions into distinct software units, called services, which can be published, requested and dynamically combined in the production of business applications. Service-oriented systems (SOSs) promise high flexibility, improved maintainability, and simple re-use of functionality. Achieving these properties requires an understanding not only of the individual artifacts of the system but also their integration. In this context, non-functional aspects play an important role and should be analyzed and modeled as early as possible in the development cycle. In this paper, we discuss modeling of non-functional aspects of service-oriented systems, and the use of these models for analysis and deployment. Our contribution in this paper is threefold. First, we show how services and service compositions may be modeled in UML by using a profile for SOA (UML4SOA) and how non-functional properties of service-oriented systems can be represented using the non-functional extension of UML4SOA (UML4SOA-NFP) and the MARTE profile. This enables modeling of performance, security and reliable messaging. Second, we discuss formal analysis of models which respect this design, in particular we consider performance estimates and reliability analysis using the stochastically timed process algebra PEPA as the underlying analytical engine. Last but not least, our models are the source for the application of deployment mechanisms which comprise model-to-model and model-to-text transformations implemented in the framework VIATRA. All techniques presented in this work are illustrated by a running example from an eUniversity case study.     

Anonymization of moving objects databases by clustering and perturbation

Preserving individual privacy when publishing data is a problem that is receiving increasing attention. Thanks to its simplicity the concept of k-anonymity, introduced by Samarati and Sweeney [1], established itself as one fundamental principle for privacy preserving data publishing. According to the k-anonymity principle, each release of data must be such that each individual is indistinguishable from at least k−1 other individuals.     

The formation and breakup of molten oxide jets under periodic excitation

The experiments on the capillary breakup of slag jets at high temperatures are presented in this article. The impact of external excitations on the disintegration process was investigated in a furnace with optical access filmed at frame rates up to 10,000 fps. A synthetic calcia‐alumina slag was used to form jets at different temperatures (1570–1660°C) and jet velocities (0.6–1.4 ms^?1). The impact of external vibration on the breakup was evident: for low jet velocities, the jet length decreased, the droplet size increased, satellite droplet formation was hindered, and a distinct “pumping mechanism” was observed. For jets with higher velocity, the jet length decreased by 30%, the droplet generation frequency increased from 20 to 250 droplets per second, the drop sizes were uniform, and satellite formation was also suppressed. In this case, the ideal case in which the volume of one wave instability forms one droplet was achieved. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3350–3361, 2014     

Terminal and transient drop rise velocity of single toluene droplets in water

The knowledge of the drop rise velocity in dispersed systems is of fundamental importance. Especially, the residence time is needed for calculation of mass transfer rates in extraction columns. This work deals with fluid dynamic measurements of toluene droplets rising in water ranging from 1.0 to 7.0 mm, with the premise of high purity of the used chemicals. The toluene/water‐system is widely used as a test system with high interfacial tension. A semiempirical correlation for pure systems to predict the terminal velocity of single rising/falling droplets based on experimental data is presented. Results show that a distinction between maximum and characteristic mean values of the drop rise velocity is necessary, especially in the diameter range 2.4–3.0 mm where unexpected velocity fluctuations occur. Two distinct terminal rise velocities were observed for 3 mm droplets. Furthermore, comparisons of the Weber‐Reynolds‐correlation and the drag coefficient with correlations from literature show good agreement. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Chevron-Notched Toughness of Materials with Rising Fracture Resistance Curves

The effect of rising resistance curves on the fracture tougness determined from chevron-notched beam tests is estimated via a set of simple numerical calculations. It is shown that for materials with a rising resistance curve, the toughnesses determined by the peak load method and by the work of fracture method are both higher than the initiation toughness, and both depend on the sample size relative to the length over which the resistance curve increases. It is also found that the toughness based on the work of fracture is higher than that based on the peak load. Fracture toughness data obtained from tests of a nickel–alumina composite are discussed in light of the results of the numerical calculation.     

Ecotoxicological evaluation of three tertiary wastewater treatment techniques via meta-analysis and feeding bioassays using Gammarus fossarum

Advanced treatment techniques, like ozone, activated carbon and TiO₂ in combination with UV, are proposed to improve removal efficiency of micropollutants during wastewater treatment. In a meta-analysis of peer-reviewed literature, we found significantly reduced overall ecotoxicity of municipal wastewaters treated with either ozone (n = 667) or activated carbon (=113), while TiO₂ and UV was not yet assessed. As comparative investigations regarding the detoxification potential of these advanced treatment techniques in municipal wastewater are scarce, we assessed them in four separate Gammarus-feeding trials with 20 replicates per treatment. These bioassays indicate that ozone concentrations of approximately 0.8 mg ozone/mg DOC may produce toxic transformation products. However, referred effects are removed if higher ozone concentrations are used (1.3 mg ozone/mg DOC). Moreover, the application of 1 g TiO₂/l and ambient UV consistently reduced ecotoxicity. Although activated carbon may remove besides micropollutants also nutrients, which seemed to mask its detoxification potential, this treatment technique reduced the ecotoxicity of the wastewater following its amendment with nutrients. Hence, all three advanced treatment techniques are suitable to reduce the ecotoxicity of municipal wastewater mediated by micropollutants and may hence help to meet the requirements of the European Water Framework Directive.     

Ozonation of secondary treated wastewater reduces ecotoxicity to Gammarus fossarum (Crustacea; Amphipoda): are loads of (micro)pollutants responsible?

Ozone application is an effective tool to reduce loads of (micro)pollutants in wastewater, however, its ecotoxicological implications are largely unknown. Therefore, the feeding rates of a leaf-shredding invertebrate (Gammarus fossarum) exposed to secondary (=non-ozone) or ozone treated wastewater were investigated to assess potential ecotoxicological effects. Two repetitive experiments resulted in significantly higher feeding rates for gammarids exposed to ozone compared to non-ozone treated wastewater sampled from a treatment plant equipped with a full-scale ozonation. A further experiment confirmed these results also for wastewater from the same treatment plant, when ozonation was conducted at the lab-scale. However, the deviations in dissolved organic carbon profiles of ozone and non-ozone wastewater did not seem to be the driving factor for the effects observed. Two additional experiments displayed on the one hand a higher feeding rate of G. fossarum if exposed to ten-fold enriched eluates from solid phase extraction cartridges loaded with ozone compared to non-ozone treated wastewater. On the other hand, the mean feeding rate of gammarids exposed to non-ozone treated wastewater, which contained hardly any (micro)pollutants (i.e. pharmaceuticals), was at the same level as wastewater from the same source additionally treated with ozone. These results suggest that not an alteration in the organic matrix but a reduction in the load of micropollutants most likely triggered the effects in the bioassay applied. Hence, the feeding rate of G. fossarum appears to be a well-suited bioassay to indicate alterations in ecotoxicological properties of wastewater due to the application of advanced oxidation processes like ozonation.     

Interconnected metal-ceramic composites by chemical means

Using a sol-gel technique, Ni/α-Al₂O₃ composites with ceramic content ranging from 33–95 vol.% have been synthesized. The process involves dispersing the metal and ceramic precursors in solution followed by calcination in a reducing environment. Fully dense composites are obtained by hot pressing at 1,400°C in an oxygen partial pressure of 10^-12 atm. For the composites containing 20 vol.% metal or higher, the metallic phase was been found to be completely continuous. All of the composites exhibited enhanced fracture toughness behavior relative to the pure ceramic.