高效液相色谱法测定化妆品中依克多因的含量

建立高效液相色谱法测定化妆品中依克多因的分析方法,采用Agilent Poroshell 120 EC-C₁₈色谱柱（100 mm×3.0 mm,2.7μm）分离,以甲醇和p H为3.0的40 mmol/L磷酸二氢钠-10 mmol/L 1-庚烷磺酸钠缓冲溶液梯度洗脱,流速0.8 m L/min,柱温30℃,检测波长210 nm。采用外标法定量测定化妆品中的依克多因含量。结果表明,依克多因在5～800 mg/L的质量浓度范围内呈现良好线性关系,相关系数为0.999 8,方法的检出限和定量限分别为0.3和1.0 mg/L。该方法具有分离效率高、分析时间短、节省溶剂等优点,解决了依克多因在C₁₈色谱柱上保留弱的问题。     

Phosphorus-doped silicon nanoparticles as high performance LIB negative electrode

Journal of Materials Science - Silicon is getting much attention as the promising next-generation negative electrode materials for lithium-ion batteries with the advantages of abundance, high...     

双功能催化剂上四氢萘加氢裂化生成单环芳烃的反应网络研究

Conversion of LCO (light cycle oil) to BTX (benzene, toluene, and xylene) is an economically valuable method for refineries. However, this approach still faces difficulties as the main reactions are not clearly understood. Here we study the detailed hydrocracking pathway of typical reactants, 1-methylnaphthalene and tetralin, through molecular simulations and experiments to improve our understanding of the conversion process of LCO to BTX. Molecular simulations demonstrate that the rate-determining step is the isomerization pathway of six-membered ring to five-membered ring in tetralin as its activation energy (ΔEa) is the highest among all the reactions and the order of ΔEa of reactions is isomerization > ring-opening ≈ side-chain cleavage. The results of experiments show that with the increase in reaction depth, i.e., through a high temperature (350 – 370 °C) and low LHSV (4.5 – 6.0 h−1), isomerization, ring-opening, and side-chain  cleavage reactions occurred, thus improving the selectivity and yield of alkyl aromatics.     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

碳纤维原丝含油率测试影响因素研究

利用改进的索氏提取回流法测量碳纤维原丝含油率.研究了溶剂回流温度、回流时间、环境湿度对测试结果的影响,结果表明:随着回流温度的提高,2小时内回流清洗效果不断增强,当回流温度大于54℃,次数大于12次,油剂清洗效果基本保持不变.可通过提高回流温度以提高单位时间内的回流次数,优化纤维含油率测试的准确性和测试效率.环境湿度对索氏提取测纤维含油率有显著影响:控制环境湿度在50～52％RH范围内,可将纤维吸潮质量变化控制在纤维质量的0.005％,油剂相对含量的0.2％～0.6％,可将测试稳定差值降低至≤0.05％,测试方法差值<0.1％,满足油剂测试工艺要求.回流时间≥2 h,回流温度≥54℃,测试环境湿度50～52％RH,索氏提取回流法油剂测试误差<0.05％.